BS EN 14141-2013 Valves for natural gas transportation in pipelines Performance requirements and tests《天然气输送用管道阀门 性能试验和要求》.pdf

《BS EN 14141-2013 Valves for natural gas transportation in pipelines Performance requirements and tests《天然气输送用管道阀门 性能试验和要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14141-2013 Valves for natural gas transportation in pipelines Performance requirements and tests《天然气输送用管道阀门 性能试验和要求》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14141:2013Valves for natural gastransportation in pipelines Performance requirements andtestsBS EN 14141:2013 BRITISH STANDARDNational forewordThis British Standard is the

2、UK implementation of EN 14141:2013. Itsupersedes BS EN 14141:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PSE/18/1, Industrial valves, steam traps, actuators andsafety devices against excessive pressure - Valves - Basic standards.A list of organ

3、izations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013IS

4、BN 978 0 580 75759 4ICS 23.060.01; 75.200Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS EN 14

5、141:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14141 June 2013 ICS 23.060.01; 75.200 Supersedes EN 14141:2003English Version Valves for natural gas transportation in pipelines - Performance requirements and tests Robinetterie pour le transport de gaz naturel par des pipelines - Exigenc

6、es de performance et essais Armaturen fr den Transport von Erdgas in Fernleitungen -Anforderungen an die Gebrauchstauglichkeit und deren Prfung This European Standard was approved by CEN on 18 April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c

7、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard ex

8、ists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national s

9、tandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,

10、 Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldw

11、ide for CEN national Members. Ref. No. EN 14141:2013: EBS EN 14141:2013EN 14141:2013 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .7 4 Functional requirements .8 5 Requirements and tests 9 6 Inspection 23 7 Quality 23 8 Type tests 23 9 Fun

12、ctional and other qualification tests 23 10 Marking 24 Annex A (normative) Type test on general design and production of pipeline valves . 25 Annex B (normative) Strength test on torque/thrust 30 Annex C (normative) Functional test on clean gas (on option) 31 Annex D (normative) Functional test for

13、abrasion resistance to dirty service of ball valves (on option) 32 Annex E (normative) Wall thickness measurement 34 Annex F (informative) Additional requirements 35 Annex G (informative) Summary of tests on product and type tests . 36 Bibliography . 41 BS EN 14141:2013EN 14141:2013 (E) 3 Foreword T

14、his document (EN 14141:2013) has been prepared by Technical Committee CEN/TC 69 “Industrial Valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Dece

15、mber 2013, and conflicting national standards shall be withdrawn at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such pate

16、nt rights. This document supersedes EN 14141:2003. The main changes compared to the previous edition are listed below: the scope was adjusted and revised; Clause 5 was specified and revised; Clause 10 was added; Annexes B, F and G were added; entire document was editorially revised and adjusted. Acc

17、ording to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, German

18、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14141:2013EN 14141:2013 (E) 4 Introduction CEN/TC 69/WG 9 has been responsible for t

19、he development of a European performance standard of valves for use in pipelines for transportation of natural gas in accordance with EN 1594. The significant properties of valves designed for a special application are defined by performance requirements accompanied by the description of tests to be

20、 carried out: by the manufacturer on the product during the manufacture; and by an independent accepted body on test samples for certification purposes; to give proof that the valve meets the performance requirements of this European Standard. A type test is included in this European Standard to sat

21、isfy the requirements of EN 1594. BS EN 14141:2013EN 14141:2013 (E) 5 1 Scope This European Standard applies to all valves (plug, ball, gate and check valves) used in onshore transmission pipelines for transport of natural gas in accordance with EN 1594, but with a differing temperature range accord

22、ing to the following three classes in accordance with EN 682: 1) - 10 C to 60 C; 2) - 20 C to 60 C; 3) the range stated by the purchaser for special design. This European Standard comprises all valves which are components of the pipeline. This European Standard specifies valves for pipelines with a

23、maximum operating pressure (MOP) over 16 bar. Control valves and safety valves are excluded from the scope of this European Standard. This European Standard specifies requirements and appropriate verification tests carried out during production and for certification purposes to verify that the valve

24、s conform to the requirements. A summary of the product and type tests is given in Annex G. This European Standard makes reference to EN 13942. All the requirements of EN 13942 should be met unless otherwise stated. Paragraphs marked with a dot indicate requirements which are identical to EN 13942.

25、Additional national requirements and tests in accordance with individual national legal regulations not yet harmonised may be necessary and are to be advised in the purchase order. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and ar

26、e indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19, Industrial valves - Marking of metallic valves EN 549, Rubber materials for seals and diaphragms

27、 for gas appliances and gas equipment EN 558, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 571-1, Non destructive testing - Penetrant testing - Part 1: General principles EN 682, Elastomeric Seals - Mat

28、erials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids EN 736-1:1995, Valves - Terminology - Part 1: Definition of types of valves EN 736-2:1997, Valves - Terminology - Part 2: Definition of components of valves EN 736-3:2008, Valves - Terminology - Part 3: Defi

29、nition of terms EN 1369:2012, Founding - Magnetic particle testing EN 1371-1:2011, Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings BS EN 14141:2013EN 14141:2013 (E) 6 EN 1435:1997, Non-destructive examination of welds Radiographic examination of welded jo

30、ints EN 1503-1, Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards EN 1503-2, Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards EN 1515-1, Flanges and their joints - Bolting - Part 1: Se

31、lection of bolting EN 1515-2, Flanges and their joints - Bolting - Part 2: Classification of bolt materials for steel flanges, PN designated EN 1594, Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements EN 10204:2004, Metallic products - Types of inspec

32、tion documents EN 10228-1:1999, Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection EN 10228-2:1998, Non-destructive testing of steel forgings - Part 2: Penetrant testing EN 10228-3:1998, Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic

33、or martensitic steel forgings EN 10228-4, Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings EN 12266-1:2012, Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance cri

34、teria - Mandatory requirements EN 12516-1, Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells EN 12516-2, Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells EN 12516-3, Valves - Shell design strength - Part 3: Exper

35、imental method EN 12517-1:2006, Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels EN 12627:1999, Industrial valves - Butt welding ends for steel valves EN 12681, Founding - Radiographic examination EN

36、 12982, Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves EN 13942:2009, Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified) EN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: T

37、est method (ISO 148-1) EN ISO 5210, Industrial valves - Multi-turn valve actuator attachments (ISO 5210) EN ISO 5211, Industrial valves - Part-turn actuator attachments (ISO 5211) EN ISO 9712:2012, Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) BS EN 14141

38、:2013EN 14141:2013 (E) 7 EN ISO 10497, Testing of valves - Fire type-testing requirements (ISO 10497) EN ISO 11666:2010, Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO 11666:2010) EN ISO 17637, Non-destructive testing of welds - Visual testing of fusion-welded joints

39、(ISO 17637) EN ISO 17638, Non-destructive testing of welds - Magnetic particle testing (ISO 17638) EN ISO 17640:2010, Non-destructive testing of welds - Ultrasonic testing - Techniques, testing levels, and assessment (ISO 17640:2010) EN ISO 23277:2009, Non-destructive testing of welds - Penetrant te

40、sting of welds - Acceptance levels (ISO 23277:2006) EN ISO 23278:2009, Non-destructive testing of welds Magnetic particle testing of welds Acceptance levels (ISO 23278:2006) MSS-SP-55-20061), Quality standard for steel castings for valves, flanges and fittings and other piping components (visual met

41、hod for evaluation of surface irregularities) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1:1995, EN 736-2:1997, EN 736-3:2008 and EN 13942:2009 and the following apply. 3.1 full opening valve valve with an unobstructed opening capable of allo

42、wing a sphere or other internal devices of the same nominal size as the valve to pass 3.2 maximum pressure differential (MPD) maximum difference between the upstream and downstream pressure across the obturator at which the obturator may be operated 3.3 reduced-opening valve valve with the opening t

43、hrough the obturator smaller than at the end connection(s) 3.4 seating surfaces contact surfaces of the obturator and seat which ensure valve sealing 3.5 stem part that connects the obturator to the operator and which may consist of one or more components Note 1 to entry: This definition applies als

44、o for shafts. 3.6 test report 1)Developed and approved by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 127 Park Street, NE, Vienna, Virginia 22180.BS EN 14141:2013EN 14141:2013 (E) 8 written statement comprising the results of the particular tests for the evalua

45、tion of the conformity of a range of valves to this European Standard 3.7 type test test carried out on one or more valves representative of the design and the manufacturing process to confirm conformance of the manufactured valves with specified requirements Note 1 to entry: A range may include val

46、ves of the same design, the same material group and the same manufacturing method but with different size designations and different allowable pressures. 3.8 type test certification granting of a certificate by an independent accepted body to prove the conformity of a range of valves with a standard

47、 3.9 piggability capability of a valve to permit the unrestricted passage of a pig 4 Functional requirements 4.1 Travel stops Travel stops shall be provided on the valve and/or operator and they shall locate the position of the obturator in the open and closed position. The travel stops shall not af

48、fect the sealing capability of the valve. They shall not shift unintentionally. In case of lever operated valves, the travel stop shall be independent from the lever. 4.2 Position of the obturator Except for check valves, the position of the obturator shall not be altered by the dynamic forces of th

49、e passing flow or in the case of screw operated gate valves by forces generated from internal pressure. 4.3 Protection of exposed stems and shafts Extended and exposed stems and shafts of valves shall be protected against dust by a stem extension casing. 4.4 Piggability Valves for transmission pipelines shall be piggable unless otherwise agreed and shall conform to the definition of the full opening valve (3.1). The dimensions for the smallest full opening valve diameter are given in EN 13942:2009, Table 1. 4.5