BS EN 13848-3-2009 Railway applications - Track - Track geometry quality - Part 3 Measuring systems - Track construction and maintenance machines《轨道交通 铁轨 铁轨几何形状质量 第3部分 测量系统 铁轨施工和维护.pdf

《BS EN 13848-3-2009 Railway applications - Track - Track geometry quality - Part 3 Measuring systems - Track construction and maintenance machines《轨道交通 铁轨 铁轨几何形状质量 第3部分 测量系统 铁轨施工和维护.pdf》由会员分享，可在线阅读，更多相关《BS EN 13848-3-2009 Railway applications - Track - Track geometry quality - Part 3 Measuring systems - Track construction and maintenance machines《轨道交通 铁轨 铁轨几何形状质量 第3部分 测量系统 铁轨施工和维护.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN13848-3:2009ICS 45.080,93.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRailway applications Track Trackgeometry qualityPart 3: Measuring systems Trackconstruction and maintenancemachinesThis British Standard was published under theauthority of the Sta

2、ndardsPolicy and StrategyCommittee on 30 June 2009 BSI 2009ISBN 978 0 580 58043 7Amendments/corrigenda issued since publicationDate CommentsBS EN 13848-3:2009National forewordThis British Standard is the UK implementation of EN 13848-3:2009.The UK participation in its preparation was entrusted to Te

3、chnicalCommittee RAE/2, Railway track components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with

4、a British Standard cannot confer immunityfrom legal obligations.BS EN 13848-3:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13848-3April 2009ICS 93.100English VersionRailway applications - Track - Track geometry quality - Part 3:Measuring systems - Track construction and maintenancemachinesA

5、pplications ferroviaires - Voie - Qualit gomtrique de lavoie - Partie 3 : Systmes de mesure - Engins de travaux etde maintenance de la voieBahnanwendungen - Oberbau - Qualitt der Gleisgeometrie- Teil 3: Messsysteme - Gleisbau- undInstandhaltungsmaschinenThis European Standard was approved by CEN on

6、19 March 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be o

7、btained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Manag

8、ement Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway

9、, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by

10、any means reservedworldwide for CEN national Members.Ref. No. EN 13848-3:2009: EBS EN 13848-3:2009EN 13848-3:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Symbols and abbreviations 6 5 Track geometry measuring system fitted on track construction

11、and maintenance machines .6 5.1 General description .6 5.2 Environmental conditions .8 5.3 Track features input 9 5.4 Data localisation 9 5.5 Measuring system/device .9 5.6 Data processing 11 5.7 Data output 11 5.8 Data storage 11 6 Testing of track geometry measuring and recording system 12 6.1 Int

12、roduction . 12 6.2 Calibration . 12 6.3 Validation by field tests 12 6.4 Routine validation . 15 Annex A (normative) Parameters measured by track construction and maintenance machine . 16 A.1 Introduction . 16 A.2 Track gauge . 16 A.3 Longitudinal level . 17 A.4 Cross level . 18 A.5 Alignment 19 A.6

13、 Twist . 20 Annex B (informative) Principles of measurement . 21 B.1 General Description 21 B.2 Longitudinal level and alignment 21 B.3 Track gauge . 21 B.4 Cross level . 22 B.5 Twist . 22 Annex C (normative) Description of field tests: values to be respected 23 C.1 General . 23 C.2 Repeatability 23

14、 C.3 Reproducibility 24 Bibliography . 25 BS EN 13848-3:2009EN 13848-3:2009 (E) 3 Foreword This document (EN 13848-3:2009) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a nation

15、al standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

16、 rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard is one of the series EN 13848 “Railway applications Track Track geometry quality” as listed below: Part 1: Characterisation of track geometry Part 2: Measuring systems Trac

17、k recording vehicles Part 3: Measuring systems Track construction and maintenance machines Part 4: Measuring systems Manual and lightweight devices Part 5: Geometric quality levels According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are

18、bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden

19、, Switzerland and the United Kingdom. BS EN 13848-3:2009EN 13848-3:2009 (E) 4 1 Scope This European Standard specifies the minimum requirements that shall be met by measuring systems fitted on track construction and maintenance machines to give an evaluation of track geometry quality when measuring

20、one or more of the parameters described in EN 13848-1. It does not seek to prescribe which parameters are to be measured, since these depend upon the measuring capabilities of the machine and the purpose for which the machine or its measuring system is used. It also sets out the acceptable differenc

21、es from EN 13848-1 when using track construction and maintenance machines to measure track geometry. It applies to track geometry measuring systems which are fitted to track construction and maintenance machines from one year after the date of implementation of this standard. 2 Normative references

22、The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13848-1:2003+A1:2008, Railway applications Tra

23、ck Track geometry quality Part 1: Characterisation of track geometry EN 13848-2:2006, Railway applications Track Track geometry quality Part 2: Measuring systems Track recording vehicles ENV 13005:1999, Guide to the expression of uncertainty in measurement 3 Terms and definitions For the purposes of

24、 this document, the following terms and definitions apply. 3.1 track construction and maintenance machine self propelled or hauled machine/vehicle designed to construct track, maintain track and/or improve the quality of track and which is equipped with track geometry measuring systems. Also referre

25、d to as “machine” in this European Standard 3.2 machine same as “track construction and maintenance machine” (3.1) 3.3 sensor device which detects, measures and translates characteristics of track geometry into quantities that can be used for further data processing 3.4 measuring direction course be

26、tween two points on a track, independent of orientation of the machine; between two given points A and B, there are two opposite directions: A to B and B to A 3.5 orientation physical positioning of a vehicle, e.g. a track construction and maintenance machine, with regards to which end of the vehicl

27、e is leading or trailing BS EN 13848-3:2009EN 13848-3:2009 (E) 5 3.6 repeatability degree of agreement between the values of successive measurements of the same parameter made under same conditions, within a short period of time, where the individual measurements are carried out on the same section

28、of track using the same measurement and interpretation methods, subject to the following: a) similar speed b) same measuring direction c) same machine/vehicle orientation d) similar environmental conditions 3.7 reproducibility degree of agreement between the values of successive measurements of the

29、same parameter made under varying conditions, within a short period of time, where the individual measurements are carried out on the same section of track using the same measurement and interpretation methods, subject to one or more of the following: a) variation of speed b) different measuring dir

30、ections c) different machine/vehicle orientations d) different environmental conditions 3.8 validation set of tests for determining if the measuring system of a track construction and maintenance machine complies with the requirements of this standard 3.9 calibration set of procedures for adjusting

31、the measuring devices of track construction and maintenance machines in order to meet the requirements of this standard 3.10 event record of a track or line-side feature that can be either technical, physical or natural 3.11 localisation information required to locate events and the measured track g

32、eometry 3.12 reference track track with known characteristics, to allow adequate testing of the track geometry measuring and recording system 3.13 transfer function refer to EN 13848-2:2006 (Annex A) 3.14 resolution refer to EN13848-1 (3.1.8) BS EN 13848-3:2009EN 13848-3:2009 (E) 6 3.15 uncertainty

33、refer to ENV 13005:1999 (2.3.5) 4 Symbols and abbreviations For the purposes of this document, the following symbols and abbreviations apply. Table 1 Symbols and abbreviations No. Symbol Designation Unit1 D1 Wavelength range 3 m B Forward 2a Max A - B Forward2b Max A - B Forward 3 Min B - A Forward4

34、a Max B - A Forward 4b Max B - A Forward5 Min A - B or B - A Reverse 6a Max A - B or B - A Reverse 6b Max A - B or B - A Reverse BS EN 13848-3:2009EN 13848-3:2009 (E) 14 Table 3 Required comparisons Type of analysis Machine with 1 measuring orientation Machine with 2 measuring orientations Repeatabi

35、lity 2a b) sections with significant (at least 70 mm) cross level; c) an average standard deviation for the longitudinal level of 2,0 mm or higher for D1; d) an average standard deviation for alignment of 1,2 mm or higher for D1. The test section shall be long enough to ensure that usable data is ob

36、tained over 500 continuous metres of track for each run. NOTE 4 For measurements with a sampling distance greater than 0,5 m (see note in 5.5.4.2), the minimum length of the test section should be extended proportionally (in the ratio of sampling distance: 0,5 m). Ideally, a reference track should b

37、e used or a comparison made with a track-recording vehicle. Design track data such as curve radii, and cross level, as well as measured values, shall be provided with the test report. 6.3.2.2 Simplified field test A simplified repeatability or reproducibility test shall be carried out in accordance

38、with the manufacturers maintenance manual in the following circumstances: a) after a maintenance or repair operation on the track geometry measuring and recording system; b) at least every two years. A simplified test shall consist of at least two runs in one direction at a constant measuring speed

39、over the same test section. The test section shall be long enough to ensure that usable data is obtained over 200 continuous metres of track for each run. NOTE For measurements with a sampling distance greater than 0,5 m (see note in 5.5.4.2), the minimum length of the test section should be extende

40、d proportionally (in the ratio of sampling distance: 0,5 m). The manufacturer shall specify the content of the simplified test to be undertaken for any relevant operation of maintenance or repair, in his maintenance manual. BS EN 13848-3:2009EN 13848-3:2009 (E) 15 Static tests shall be carried out f

41、or example to ensure that there are no offsets in the measurement of cross level and track gauge. The results of the tests shall comply with the requirements of Annex C. 6.3.3 Comparison between different runs Statistical analysis of parameter data shall be used to compare recording runs. Calculatio

42、ns shall be made for each parameter to be validated and for each comparison. They consist of the following steps: a) precise spatial synchronisation of the recorded signals; b) calculation of the difference between the values; c) evaluation of the distribution of the differences. 6.4 Routine validat

43、ion During measuring operations, suitable periodic checking shall be carried out by the operators in accordance with the manufacturers specifications. At least once per shift, static tests shall be carried out for example to ensure that there are no offsets in the measurement of cross level and trac

44、k gauge. BS EN 13848-3:2009EN 13848-3:2009 (E) 16 Annex A (normative) Parameters measured by track construction and maintenance machine A.1 Introduction As this standard takes account of the actual equipment on existing machines and as track geometry measurements are not the main functions of machin

45、es, the EN 13848-1 requirements have to be relaxed. Therefore, this Annex lists in tabular form the minimum requirements for each track geometry parameter which can be measured by machines. Requirements differing from EN 13848-1 are highlighted in bold. The requirements of EN 13848-1 are shown only

46、for comparison purposes. A.2 Track gauge Table A.1 Track gauge Comparison with the requirements of EN 13848-1 Characteristic Requirements of EN 13848-3 Requirements of EN 13848-1 Comment Measurement method Track gauge, G, is the smallest distance between lines perpendicular to the running surface in

47、tersecting each rail head profile at point P in a range from 0 to Zp below the running surface. Zp is always 14 mm Track gauge, G, is the smallest distance between lines perpendicular to the running surface intersecting each rail head profile at point P in a range from 0 to Zp below the running surf

48、ace. Zp is always 14 mm Wavelength range N/A N/A Resolution 0,5 mm 0,5 mm Uncertainty 1 mm 1 mm Range - 15 mm / + 50 mm - 15 mm / + 50 mm Analysis method No real time numerical analysis or additional processing required Nominal value to peak value Output requirements Graphical and digital Set of rea

49、dings recorded preferably in digital form and shall also be presented graphically Output presentation Track gauge or the difference between measured and nominal gauge Individual defects Track gauge Difference between measured and nominal gauge Mean track gauge over a specified distance Variation of track gauge over a specified distance BS EN 13848-3:2009EN 13848-3:2009 (E) 17 A.3 Longitudinal level Table A.2 Longitudinal level Comparison with the requirements of EN 13848-1 Characteristic Requirements of EN 13848-3 Requ