BS EN 10349-2009 Steel castings - Austenitic manganese steel castings《钢铸件 奥氏体锰钢铸件》.pdf

《BS EN 10349-2009 Steel castings - Austenitic manganese steel castings《钢铸件 奥氏体锰钢铸件》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10349-2009 Steel castings - Austenitic manganese steel castings《钢铸件 奥氏体锰钢铸件》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 10349:2009ICS 77.080.10; 77.140.80NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSteel castingsAusteniticmanganesesteel castingsThisBritishStandardwas publishedundertheauthorityoftheStandardsPolicyandStrategy Committee on30November2009.BSI2009ISBN 9780580

2、 59025 2Amendments/corrigenda issued sincepublicationDate CommentsBS EN 10349:2009National forewordThisBritish Standardisthe UKimplementationofEN10349:2009.TheUKparticipationinitspreparationwasentrustedtoTechnicalCommitteeISE/6,Steelcastings.Alistof organizationsrepresentedonthiscommitteecanbeobtain

3、edonrequesttoitssecretary.Thispublicationdoesnotpurporttoincludeallthenecessaryprovisionsofacontract.Usersareresponsibleforitscorrectapplication.Compliance withaBritish Standard cannotconfer immunityfrom legal obligations.BS EN 10349:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 10349 Octo

4、ber 2009 ICS 77.080.10English Version Steel castings - Austenitic manganese steel castings Aciers mouls - Pices moules en aci er austnitique au manganse Stahlguss - Austenitischer Manganst ahlgussThis European Standard was approved by CEN on 15 September 2009.CEN members are bound to comply with the

5、 CEN/CENELEC Internal Regulations wh ich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s uch nationalstandards may be obtained on application to the CEN Management Centre

6、 or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official v

7、ersions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, S

8、pain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Me

9、mbers.Ref. No. EN 10349:2009: EBS EN 10349:2009EN 10349:2009 (E)2 Contents PageForeword 31Scope 42Normative references43 Terms and definitions .44 Information to be supplied by the purchaser .45 Designation 56 Manufacture 57 Requirements .58Testing and documents on material testing.69 Marking .710 P

10、ackaging and surface protection .711 Complaints .712 Supplementary information 7BS EN 10349:2009EN 10349:2009 (E)3 Foreword This document (EN 10349:2009) has been prepared by Technical Committee E CISS/TC31 “Steel castings”,the secretariat of which is held by AFNOR.This European Standard shall be gi

11、ven the status ofa national standard, either by publication of an identical text or by endorsement, at the latestbyApril 2010, and conflicting national standards shall be withdrawn at the latest by April 2010.Attention is drawn to the possibility that some of the elements of this document may be the

12、 subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any orall such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium,

13、 Bulgaria, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Fran ce, Germany, Greece, Hungar y, Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the UnitedKingdom. BS EN 10349:2009EN 1034

14、9:2009 (E)4 1 ScopeThis European Standard specifies austenitic manganese cast steels for wear-resistant service. The gradescovered by this European Standard will experience maximumse rvice life in applications where the surface of the casting is subject to impact.This European Standard retains the s

15、a me format for clauses as EN 1559-1 and EN1559-2. It shall be used inconjunctionwith these standards. Where no text is given under a clause heading, the corresponding clauseof EN 1559-1 or EN 1559-2 applies. The structure of this standard is as follows:a) clauses and subclauses preceded by indicate

16、s no additional conditions to Part 1 or Part21)of EN 1559;b) subclauses without any marking are mandatory.2 NormativereferencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the l

17、atest edition of the referenceddocument (including any amendments) applies.EN 1559-1, Founding Technical conditions of delivery Part1: GeneralEN 1559-2, Founding Technical conditions of delivery Part2: Additional requirements for steel castingsEN ISO 6506-1, Metallic materials Brinell hardnesstest P

18、art 1: Test method (ISO 6506-1:2005)EN ISO 7438, Metallic materials Bend test (ISO 7438:2005)3 Terms and definitions 4 Information to be supplied by the purchaser In addition to EN 1559-1 and EN 1559-2:Materials furnished according to this European Standard shall conform to the applicable requiremen

19、ts of EN 1559-1 and EN 1559-2 including the supplementary requirements that are agreed in the inquiryand purchase order.1) When additional information is given in a clause or subclause of this standard (versus the same clause or subclauseof EN 1559-1 or EN 1559-2) it is preceded by: “In addition to

20、EN 1559:“.BS EN 10349:2009EN 10349:2009 (E)5 5 Designation6 Manufacture 6.1 Manufacture process6.1.1 Melting6.1.2 Heat treatmentIn addition to EN 1559-1 and EN 1559-2:Grade GX90MnMo14may be supplied without heat treatment if the casting thickness is lessthan45 mm andthe carbon content is less than 0

21、,8 %.Where the thickness is 45 mm or greater and the carbon content is 0,8 % or greater Grade GX90MnMo14,and all other grades, shall be solution treated at temperatures not lower than 1 040 C and quenched in water.7 Requirements7.1 General7.2 Material7.2.1 ChemicalcompositionIn addition to EN 1559-1

22、 and EN 1559-2:The chemical composition determined by a cast analysis shall conform with the values given in Table 1.7.2.2 Mechanical properties7.2.2.1 GeneralMechanical testing at room temperature shall be performed when agreed upon between t he purchaser andmanufacturer.7.2.2.2 BendtestBend tests

23、shall be carried out in accordance with EN ISO 7438. The type and location of bend test pieces shall be agreed between the manufacturer and purchaser. The test specimen shall withstand bending at roomtemperature (23 5) C through an angle of 150 without breaking into two or more pieces. Surface crack

24、sproduced by bending are not considered as failure if the test piece remains in one piece.7.2.2.3 Brinell Hardness testHardness tests shall be carried out in accordance with EN ISO6506-1. The hardness shall be a maximumof 300 HBW, unless otherwise agreed between the manufacturer and purchaser.When m

25、achining of castings is required, it may be necessary to control hardness. In this case hardness testing shall be carried out afterheat treatment and prior to machining.BS EN 10349:2009EN 10349:2009 (E)6 7.2.3 Microstructure Metallographic examination shall be performed when agreed upon between the

26、manufacturer and purchaser.Standard microstructure charts may be agreed between the manufacturer and purchaser. 7.3 Casting8 Testing and documents on material testing 8.1 General8.2Inspection and testing8.2.1 Types of inspection and testing8.2.2 Non specific inspection and testing8.2.3 Specific insp

27、ection and testing8.2.4 Continuous inspection8.2.5 Place of specific inspection and testingInspections and tests shall be carried out at a place agreed upon between the manufacturer and purchaser.Samples may be selected in the manufacturers works. Dependingon the type of test, samples may be blockso

28、r castings representative of the product.8.2.6 Submission for specific inspection and testing to the inspectionrepresentative8.2.6.1 GeneralThe manufacturer shall arrange with the purchaser, by mutualagreement, the date of submission forinspection.The inspection representative shall have free access

29、 at any suitable time to the places inwhich the products to be inspected are manufactured and stored. He mayindicate the samples to be selected in accordance withthe specification. He shallhave the option of attending the selection of samples, the preparation (machiningand treatment) of the test pie

30、ces and carrying out the tests. However, an inspection representativewho visitsthe workshops shall respect all of the safety regulations in force in the works and shall be accompanied, as faras possible, by a representative of this works.8.2.6.2Conditions of acceptanceIf all the requirements ofthe o

31、rder, and of this European Standard, are fulfilled, the lot is considered toconform and is accepted by the purchaser without prejudice to the inspection which may take place later at the purchasers works within the time limits specified by agreement between themanufacturer and purchaser. BS EN 10349

32、:2009EN 10349:2009 (E)7 8.3 Test unit sampling8.4 Samples (test block)8.5 Test methodsa) tensile test at room temperature (not applicable);b) tensile test at elevated temperature, verification by agreement at the time of enquiryand order (notapplicable;c) impact test (not applicable);d) ferrite cont

33、ent;e) hardnesstest;f) homogeneityof test unit (hardness test);g) pressure or leak testing;h) intergranular corrosion test(not applicable );i) testfor magnetic properties; j) other test for any other properties.8.6 Invalidationoftests8.7 Retests8.8 Sortingand reprocessing 9 Marking10 Packaging and s

34、urface protection11 Complaints12 Supplementary information A list of standardized supplementary requirements for use at the discretion of the purchaser is includedin EN 1559-1 and EN 1559-2. Those which are ordinarily considered suitable for use with this specification are given above. The details o

35、f these are listed inEN1559-1 and EN 1559-2. Others, whether or not contained in EN 1559-1 and EN 1559-2, may be used with this European Standard upon agreement between themanufacturer and purchaser. EN 10349:2009 (E)8 Table 1 Chemicalcomposition (castanalysis)DesignationChemicalcomposition% by mass

36、C SiMnP S Cr MoNiNameNumbermax.max.GX120MnMo7-11.3415 1,05 to0,3 to6 to0,060 0,045 0,9 to 1,35 0,9 8 1,2 GX110MnMo13-11.3416 0,75 to0,3 to11 to0,060 0,045 0,9 to 1,35 0,9 14 1,2 GX100Mn13a1.3406 0,90 to0,3 to11 to0,060 0,045 1,05 0,9 14 GX120Mn13a1.3802 1,05 to0,3 to11 to0,060 0,045 1,35 0,9 14 GX12

37、0MnCr13-21.3410 1,05 to0,3 to11 to0,060 0,045 1,5 to 1,35 0,9 14 2,5 GX120MnNi13-31.3425 1,05 to0,3 to11 to0,060 0,045 3 to1,35 0,9 14 4 GX120Mn18a1.3407 1,05 to0,3 to16 to0,060 0,045 1,35 0,9 19 GX90MnMo141.3417 0,70 to0,3 to13 to0,070 0,045 1,0 to 1,00 0,6 15 1,8 GX120MnCr18-21.3411 1,05 to0,3 to1

38、6 to0,060 0,045 1,5 to 1,35 0,9 19 2,5 aThese grades are sometimes usedfor non magneticserviceBS EN 10349:2009This page has been intentionally left blank BSEN10349:2009BSIGroupHeadquarters389ChiswickHighRoad,London,W44AL,UKTel+44(0)2089969001Fax+44(0) -British Standards InstitutionBSIistheindependen

39、tnationalbodyresponsibleforpreparingBritishStandards.ItpresentstheUKviewonstandardsinEuropeandattheinternationallevel.ItisincorporatedbyRoyalCharter.RevisionsBritishStandardsareupdatedbyamendmentorrevision.UsersofBritishStandardsshouldmakesurethattheypossessthelatestamendmentsoreditions.Itistheconst

40、antaimofBSItoimprovethequalityofourproductsandservices.WewouldbegratefulifanyonefindinganinaccuracyorambiguitywhileusingthisBritishStandardwouldinformtheSecretaryofthetechnicalcommitteeresponsible,theidentityofwhichcanbefoundontheinsidefrontcover.Tel:+44(0)2089969000.Fax:+44(0)2089967400.BSIoffersme

41、mbersanindividualupdatingservicecalledPLUSwhichensuresthatsubscribersautomaticallyreceivethelatesteditionsofstandards.Buying standardsOrdersforallBSI,internationalandforeignstandardspublicationsshouldbeaddressedtoCustomerServices.Tel:+44(0)2089969001.Fax:+44(0)2089967001Email:Youmayalsobuydirectlyusingadebit/creditcardfromtheBSIShopontheWebsitehttp:/