BS EN 4113-2009 Aerospace series - Clamps loop ( P type) in corrosion resisting steel passivated with rubber cushioning - Dimensions masses《航空航天系列 带橡胶弹性衬料的耐腐蚀钝化的钢制环形(P型)卡箍 尺寸和质量》.pdf

《BS EN 4113-2009 Aerospace series - Clamps loop ( P type) in corrosion resisting steel passivated with rubber cushioning - Dimensions masses《航空航天系列 带橡胶弹性衬料的耐腐蚀钝化的钢制环形(P型)卡箍 尺寸和质量》.pdf》由会员分享，可在线阅读，更多相关《BS EN 4113-2009 Aerospace series - Clamps loop ( P type) in corrosion resisting steel passivated with rubber cushioning - Dimensions masses《航空航天系列 带橡胶弹性衬料的耐腐蚀钝化的钢制环形(P型)卡箍 尺寸和质量》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 4113:2009ICS 49.030.99NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Clamps, loop (P type)in corrosion resistingsteel, passivated withrubber cushioning Dimensions, massesThis British Standardwas published underthe authority of theStandard

2、s Policy andStrategy Committee on 30November 2009 BSI 2009ISBN 978 0 580 59235 5Amendments/corrigenda issued since publicationDate CommentsBS EN 4113:2009National forewordThis British Standard is the UK implementation of EN 4113:2009. Itsupersedes BS EN 4113:2001 which is withdrawn.The UK participat

3、ion in its preparation was entrusted to TechnicalCommittee ACE/69, Aerospace hydraulic systems, fluids andcomponents.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract

4、. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 4113:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4113 October 2009 ICS 49.030.99 Supersedes EN 4113:2001English Version Aerospace series - Clamps, lo

5、op (P type) in corrosion resisting steel, passivated with rubber cushioning - Dimensions, massesSrie arospatiale - Colliers en P en acier rsistant la corrosion, passivs avec profil en lastomre - Dimensions, masses Luft- und Raumfahrt - Schellen in Schlaufenform (P-Form) aus korrosionsbestndigem Stah

6、l, passiviert mit Profilgummi - Mae, Massen This European Standard was approved by CEN on 5 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteratio

7、n. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translat

8、ion under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,

9、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Mana

10、gement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4113:2009: EBS EN 4113:2009EN 4113:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics

11、 .44 Designation . 105 Marking 106 Technical specification 10BS EN 4113:2009EN 4113:2009 (E) 3 Foreword This document (EN 4113:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with

12、the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identic

13、al text or by endorsement, at the latest by April 2010, and conflicting national standards shall be withdrawn at the latest by April 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respon

14、sible for identifying any or all such patent rights. This document supersedes EN 4113:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repu

15、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4113:2009EN 4113:2009 (E) 4 1 Scope This Euro

16、pean Standard specifies the required characteristics of loop style clamps (“P” type) in corrosion resisting steel, passivated with various cushion materials. These clamps are used for supporting aerospace pipe assemblies and electrical cable bundles. For temperature range and environmental considera

17、tions see the various cushion material standards. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a

18、ny amendments) applies. EN 2261, Aerospace series Silicone rubber (VMQ) Hardness 70 IRHD EN 2424:2008, Aerospace series Marking of aerospace products EN 2516, Aerospace series Passivation of corrosion resisting steels and decontamination of nickel base alloys EN 2566, Aerospace series Fluorocarbon r

19、ubber Hardness 70 Characteristics1)EN 3078, Aerospace series P, Q and saddle clamps with rubber cushion Technical specification1)EN 3488, Aerospace series Steel FE-PA3601 (X6CrNiTi18-10) Air melted Softened Sheet and strip a 6 mm 500 MPa Rm 700 MPa EN 3825, Aerospace series Fluorosilicone rubber (FV

20、MQ) Hardness 60 IRHD1)EN 3826, Aerospace series Fluorosilicone rubber (FVMQ) Hardness 70 IRHD1)EN 4115, Aerospace series Cushion, rubber for clamps Dimensions, masses EN 10088 (all parts), Stainless steels 3 Required characteristics 3.1 Materials According to Table 1. Clamp: According to EN 3488 (al

21、ternative material 1.4541 according to EN 10088). Cushion: According to EN 4115. 1) Published as ASD Prestandard at the date of publication of this standard. BS EN 4113:2009EN 4113:2009 (E) 5 Table 1 Cushion materials Cushion material code Elastomer Colour S Silicone VMQ EN 2261 rust F Fluorosilicon

22、e FVMQ EN 3826 a blue V Fluorocarbon FPM EN 2566 b brown aAlternative EN 3825. bAlternative Fluorocarbon rubber (FPM) Hardness 75 IRHD (Class 60C7). 3.2 Surface treatment According to EN 2516. 3.3 Configuration Dimensions Masses See Figures 1 to 2 and Table 2. Rubber cushion dimensions, see EN 4115.

23、 BS EN 4113:2009EN 4113:2009 (E) 6 Dimensions in millimetres a) Form with round hole b) Form with slotted hole in lower foot, code letter R in lower foot, code letter H aDelivery position bRubber cushion and t1and t2according to EN 4115 cArea for marking dStiffening deformation on both sides as draw

24、n, or central at the manufacturers option Figure 1 Configuration of clamp with rubber cushion BS EN 4113:2009EN 4113:2009 (E) 7 aRubber cushion according to EN 4115 NOTE Possible forms of cushion with alternative wedge according to EN 4115 (at manufacturers option). Figure 2 Configuration of clamp w

25、ith rubber cushion, wedge version (Form W) BS EN 4113:2009EN 4113:2009 (E) 8 Table 2 Dimensions, masses Diameter code b1b2ad be1 e2 e3 r s acMass kg/1 000 partsCushion type according to EN 4115 0,25 max. 0,4 0,4 0,4 0,4 max. max. Without wedge With wedge 03 09,5 14,4 3 11,5 4,7 5,7 1,6 1,6to 2 0,8 4

26、,5 1N 1K 04 4 12,0 6,2 5,25 05 5 12,5 6,7 5,55 06 6 13,0 7,2 6,15 07 7 13,5 7,7 6,45 08 8 14,0 8,2 7,05 09 9 14,5 8,7 7,5 10 10 15,0 9,2 8,1 11 11 15,5 9,7 8,55 12 12 16,0 10,2 8,85 13 12,7 18 13 16,5 5,5 10,7 2,5 011,25 2N 2K 14 14 18,7 11,2 012,3 15 15 19,2 11,7 012,6 16 16 19,7 12,2 012,75 17 17

27、20,2 12,7 013,35 18 18 20,7 13,2 013,8 2L 19 19 21,2 13,7 014,25 20 20 21,7 14,2 014,85 21 21 22,2 14,7 15,45 22 22 22,7 15,2 16,05 23 23 23,2 15,7 16,65 24 24 23,9 16,2 17,4 25 25 24,2 16,7 18 26 26 24,9 17,2 18,45 27 27 25,7 17,7 19,2 28 28 26,2 5,5 18,5 3 2,5to 3,3 21,3 4N 4L 29 29 26,9 19,0 21,9

28、 30 30 27,2 19,5 22,35 31 31 27,9 20,0 22,8 32 32 28,2 20,5 23,1 33 33 28,9 21,0 23,55 34 34 29,2 21,5 24,45 35 35 29,9 22,0 24,9 36 36 30,2 22,5 25,65 37 37 30,9 23,0 25,95 38 38 31,2 23,5 26,4 40 40 32,2 24,5 27,3 41 41 32,9 25,0 28,8 43 43 33,7 26,0 30,45 45 45 34,9 27,0 31,95 46 46 35,2 27,5 33

29、continued BS EN 4113:2009EN 4113:2009 (E) 9 Table 2 Dimensions, masses (concluded) Diameter code b1b2a d b e1 e2 e3 r s ac Mass kg/1 000 parts Cushion type according to EN 4115 0,25 max. 0,4 0,4 0,4 0,4 max. max. Without wedge With wedge 48 12,7 18 48 36,4 5,5 28,7 3 3,0to 3,8 1 34,8 5N 5L 49 49 36,

30、9 29,2 36,3 50 50 37,2 29,7 41,25 51 51 37,9 30,2 43,8 52 52 38,4 30,7 44,4 54 54 39,4 31,7 44,7 55 55 39,7 32,2 45,3 5N 5L 56 56 40,4 32,7 46,5 57 57 40,9 33,2 47,7 58 58 41,4 33,7 48,15 59 59 41,9 34,2 49,2 60 60 42,4 34,7 49,95 61 61 42,9 35,2 50,7 62 62 43,4 35,7 51,45 63 63 43,9 36,2 52,2 64 64

31、 44,4 36,7 52,95 65 65 44,9 37,2 53,7 66 66 45,4 37,7 54,45 68 68 46,4 38,7 56,25 69 69 46,9 39,2 57 70 70 47,4 39,7 57,75 71 71 47,9 40,2 58,8 73 73 49,0 41,7 60,15 76 76 50,0 42,7 61,65 79 79 51,9 44,2 64,05 80 80 52,4 44,7 64,5 83 83 53,9 46,2 66,75 86 86 55,0 47,7 69 NOTE Mass data referring to

32、Silicon rubber material with a mass density of 1,23 g/cm3(see EN 4115 for other cushion materials). aAs per EN 4115. bOutside diameter of the corresponding pipe. cTolerances in accordance with semi-finished product. BS EN 4113:2009EN 4113:2009 (E) 10 4 Designation EXAMPLE Description block CLAMP Ide

33、ntity block EN4113F20WH Number of this standard Code letter for cushion material (see Table 1) Diameter code (see Table 2) Code letter only for wedged cushion, if required (see Figure 2) Without wedge: code letter N Code letter for hole version, if required (see Figure 1) NOTE If necessary, the code

34、 I9005 shall be placed between the description block and the identity block. 5 Marking According to EN 2424:2008, style B and Figure 1. It shall contain: number of the standard; diameter code; code letter for form; EXAMPLE EN 411320H cushion material indicated by colour of cushion (see Table 1); wed

35、ged cushion indicated by code letter on the cushion (see EN 4115). 6 Technical specification According to EN 3078. BS EN 4113:2009This page has been intentionally left blank BS EN4113:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - Briti

36、sh Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British

37、Standards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technic

38、al committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standards

39、Orders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international stan

40、dards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to Ex

41、portersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive

42、 substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ inf

43、ormation about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract m

44、aybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: