BS EN 35-2014 Pedestal and wall-hung bidets with over-rim supply Connecting dimensions《沿缘供水立柱式和壁挂式坐浴盆 连接尺寸》.pdf

《BS EN 35-2014 Pedestal and wall-hung bidets with over-rim supply Connecting dimensions《沿缘供水立柱式和壁挂式坐浴盆 连接尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS EN 35-2014 Pedestal and wall-hung bidets with over-rim supply Connecting dimensions《沿缘供水立柱式和壁挂式坐浴盆 连接尺寸》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 35:2014Pedestal and wall-hungbidets with over-rim supply Connecting dimensionsBS EN 35:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 35:2014. It supersedes BS EN 35:2000 and BS EN 36:1999 which are withdrawn.The UK participa

2、tion in its preparation was entrusted to Technical Committee B/503, Sanitary appliances.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for

3、 its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 79613 5 ICS 91.140.70 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Poli

4、cy and Strategy Committee on 31 May 2014.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 35:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 35 May 2014 ICS 91.140.70 Supersedes EN 35:2000, EN 36:1998English Version Pedestal and wall-hung bidets with over-rim supply - Co

5、nnecting dimensions Bidets sur pied et bidets suspendus alimentation par surverse - Cotes de raccordement Bodenstehende und wandhngende Sitzwaschbecken mit Zulauf von oben - Anschlussmae This European Standard was approved by CEN on 10 April 2014. CEN members are bound to comply with the CEN/CENELEC

6、 Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or t

7、o any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offici

8、al versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N

9、orway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of ex

10、ploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 35:2014 EBS EN 35:2014EN 35:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Tap holes 4 3.1 General 4 3.2 Connecting dimensions of bidets with one central tap hole 4 3.3 Connecti

11、ng dimensions of bidets with three tap holes .6 4 Waste outlet holes .7 4.1 Connecting dimensions of waste outlet hole with integral overflow .7 4.2 Connecting dimensions of waste outlet hole without integral overflow .8 4.3 Waste outlet arrangements for pedestal bidets .9 5 Fixing dimensions of wal

12、l-hung bidets .9 Annex A (informative) Example of a gauge for measuring the connecting dimensions of waste outlet hole 11 BS EN 35:2014EN 35:2014 (E) 3 Foreword This document (EN 35:2014) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by U

13、NI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2014 and conflicting national standards shall be withdrawn at the latest by November 2014. Attention is drawn to the possibility that s

14、ome of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights This document supersedes EN 35:2000, EN 36:1998. This document differs from EN 35:2000 and EN 36:1998 as follows: a) these two Euro

15、pean Standards covering connecting dimensions for various types of bidets have been combined in one European Standard; b) part of connecting dimensions have been modified taking into account current model developments; c) part of designations have been clarified to improve readability of standard an

16、d to dissolve double designations. This document combines connecting dimensions standards for different types of bidets. It introduces modifications on dimensions and new designations to improve the readability and dissolve double designations. According to the CEN-CENELEC Internal Regulations, the

17、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

18、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 35:2014EN 35:2014 (E) 4 1 Scope This European Standard specifies the connecting dimensions of pedestal and wall-hung bidets with over-ri

19、m supply (further on: bidets) in accordance with EN 14528 regardless of materials used for their manufacture. NOTE 1 Other connecting dimensions are permitted, e. g. special designs of bidets, if the manufacturer supplies or recommends the appropriate fitting. NOTE 2 The shape of the appliance in th

20、e figures is for illustration only; it in no way prejudices the final shape of the appliance, which is left to the initiative of the manufacturer. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicatio

21、n. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14528, Bidets - Functional requirements and test methods 3 Tap holes 3.1 General The connecting dimensions for tap holes are requireme

22、nts for bidets where it is intended to fit a tap. 3.2 Connecting dimensions of bidets with one central tap hole The connecting dimensions of bidets with one central tap hole shall comply with Table 1. BS EN 35:2014EN 35:2014 (E) 5 Table 1 Connecting dimensions of bidets with one central tap hole (Fi

23、gure 1) Designation Symbol Dimensions mm Diameter of the tap hole (intended to accommodate a mixer tap) d2a352+1-Horizontal distance between the centre line of the central tap hole and the edge of the bowl g1 80 Distance from the centre line of the central tap hole to the back wall g3 55 Radius of a

24、 cylinder having the same centre line as the central tap hole at a depth 0 mm to 5 mm from the lower plane of the central tap hole r1 25 Radius of a cylinder having the same centre line as the central tap hole at a depth of minimum 5 mm from the lower plane of the central tap hole r2 30 Radius of a

25、flat plane circular surface on the tap platform having the same centre as the central tap hole and intended to accommodate the tap r3 32 Thickness of the platform at the level of the zone concentric to the central tap hole s 18 Horizontal distance between the centre line of the central tap hole and

26、the centre line of the waste outlet hole t b 170 aThe diameter 302+0is permissible with r1 22 and r2 25. bMay not be applicable for bidets of class CL 00 in accordance with EN 14528. Dimensions in millimetres Figure 1 Connecting dimensions of bidets with one central tap hole BS EN 35:2014EN 35:2014

27、(E) 6 3.3 Connecting dimensions of bidets with three tap holes The connecting dimensions of bidets with three tap holes shall comply with Table 2. Table 2 Connecting dimensions of bidets with three tap holes (Figure 2) Designation Symbol Dimensions mm Diameter of outer tap holes d1302+0Diameter of t

28、he central tap hole d2352+1-Distance from the centre line of the central hole to the centre line of the two outer tap holes e 0 to 15 Distance between the centre lines of the two outer tap holes f 175 15 Horizontal distance between the centre line of the central tap hole and the edge of the bowl g1

29、80 Distance from the centre line of the central tap hole to the back wall g3 55 Shortest horizontal distance between the centre lines of the outer tap holes and the edge of the bowl when only the two outer tap holes are used g4 65 Radius of a cylinder having the same centre line as the central tap h

30、ole at a depth 0 mm to 5 mm from the lower plane of the central tap hole r1 25 Radius of a cylinder having the same centre line as the central tap hole at a depth of minimum 5 mm from the lower plane of the central tap hole r2 30 Radius of a flat plane circular surface of the tap platform having the

31、 same centre as the central tap hole and intended to accommodate the tap r3 32 Radius of a flat plane circular surface of the tap platform having the same centre as the outer tap holes and intended to accommodate the side valves r4 30 Thickness of the platform at the level of the zone concentric to

32、the tap holes s 18 Horizontal distance between the centre line of the central tap hole and the centre line of the waste outlet hole t a 170 aMay not be applicable for bidets of class CL 00 in accordance with EN 14528. BS EN 35:2014EN 35:2014 (E) 7 Dimensions in millimetres Figure 2 Connecting dimens

33、ions of bidets with three tap holes 4 Waste outlet holes 4.1 Connecting dimensions of waste outlet hole with integral overflow The connecting dimensions of the waste outlet hole with integral overflow shall comply with the dimensions given in Table 3. Table 3 Connecting dimensions of the waste outle

34、t hole with integral overflow (Figure 3) Designation Symbol Dimension mm Bore of the waste outlet hole d3462+-3Diameter of the base for the seal between the waste outlet hole and the waste fitting d4 60 Reference diameter to measure the height of the waste outlet hole (h1) d563 Height of the waste o

35、utlet hole measured between the reference diameter d5and the base for the seal h14505-+Height measured between the reference diameter d5and the bottom of the bowl h2 2 Vertical distance between the tap platform and the base for the seal p 250 Cone angle of the upper section of the waste outlet hole

36、100 NOTE To verify the connecting dimensions in accordance with Table 3, it is recommended to use a gauge in accordance with Annex A. BS EN 35:2014EN 35:2014 (E) 8 Figure 3 Connecting dimensions of the waste outlet hole for bidets with integral overflow 4.2 Connecting dimensions of waste outlet hole

37、 without integral overflow The connecting dimensions of the waste outlet hole without integral overflow shall comply with the dimensions given in Table 4. Table 4 Connecting dimensions of the waste outlet hole without integral overflow (Figure 4) Designation Symbol Dimension mm Bore of the waste out

38、let hole d3462+-3Diameter of the base for the seal between the waste outlet hole and the waste fitting d4 60 Reference diameter to measure the height of the waste outlet hole (h3) d563 Height measured between the reference diameter d5and the bottom of the bowl h2 2 Height of the waste outlet hole me

39、asured between the reference diameter d5and the base for the seal h3a2005-Cone angle of the upper section of the waste outlet hole 100 NOTE To verify the connecting dimensions in accordance with Table 4, it is recommended to use a gauge in accordance with Annex A. aThe height h3= 4505-is permissible

40、.BS EN 35:2014EN 35:2014 (E) 9 Figure 4 Connecting dimensions of the waste outlet hole for bidets without integral overflow 4.3 Waste outlet arrangements for pedestal bidets The distance m from the lower edge of waste outlet hole to the base of the appliance shall be 180 mm (see Figure 5). Figure 5

41、Waste outlet arrangement for pedestal bidets 5 Fixing dimensions of wall-hung bidets The fixing dimensions of wall-hung bidets shall comply with the dimensions given in Table 5. Table 5 Fixing dimensions of wall-hung bidets (Figure 6) Designation Symbol Dimension mm Horizontal distance between the c

42、entre lines of the two fixing holes n 180 5 230 5 Diameter of clear opening of fixing holes NOTE Other hole shapes are permissible. d625 3 Thickness of appliance around the fixing holes v 80 80 aa 80 is permissible provided that additional mounting parts are recommended or supplied by the manufactur

43、er. BS EN 35:2014EN 35:2014 (E) 10 Figure 6 Fixing dimensions of wall-hung bidets BS EN 35:2014EN 35:2014 (E) 11 Annex A (informative) Example of a gauge for measuring the connecting dimensions of waste outlet hole Dimensions in millimetres Figure A.1 Example of a gauge to verify the connecting dime

44、nsions of waste outlet holes with or without integral overflow This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charte

45、r. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their com

46、bined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their

47、goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI pub

48、lications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.S

49、ubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and re