BS EN 2103-2-1992 Steel nickel base and cobalt base alloy remelting stock and castings - Technical specification - Remelting stock《钢、镍基合金及钴基合金重熔坯料和铸件 技术规范 重熔坯料》.pdf

《BS EN 2103-2-1992 Steel nickel base and cobalt base alloy remelting stock and castings - Technical specification - Remelting stock《钢、镍基合金及钴基合金重熔坯料和铸件 技术规范 重熔坯料》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2103-2-1992 Steel nickel base and cobalt base alloy remelting stock and castings - Technical specification - Remelting stock《钢、镍基合金及钴基合金重熔坯料和铸件 技术规范 重熔坯料》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2103-2:1992 Steel, nickel base and cobalt base alloy remelting stock and castings Technical specification Part 2: Remelting stock This European Standard EN 2103-2:1991 has the status of a British StandardBSEN 2103-2:1992 This British Standard was published und

2、er the authority of the Standards Board and comes into effect on 31January1992 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/61 Draft for comment 88/77546 DC ISBN 0 580 20385 9 Cooperating organizations The European Committee for Standardizatio

3、n, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries. Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. F

4、rance Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Tr

5、avail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United

6、Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN 2103-2:1992 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN 2103-2 3 National appendix NA (informative) Inside back cover National

7、appendix NB (informative) Inside back coverBSEN 2103-2:1992 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2103-2:1991 “Aerospace series Steel, nickel base and cobalt ba

8、se alloy remelting stock and castings Technical specification Part 2: Remelting stock”, published by the European Committee for Standardization (CEN). EN 2103-2 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include al

9、l the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and

10、 ii, theEN title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2103-

11、2 October 1991 UDC: 669.14-4:669.25-4:669.24-4:629.7 Descriptors: Aircraft industry, castings, steels, nickel alloys, cobalt alloys, manufacturing, melting, defects, mechanical tests, marking English version Aerospace series Steel, nickel base and cobalt base alloyremelting stock and castings Techni

12、cal specification Part 2: Remelting stock Srie arospatiale Produits pour refusion et pices moules en acier et alliages base nickel et base cobalt Spcification technique Partie2: Produits pour refusion Luft- und Raumfahrt Vormaterial und Gustcke aus Stahl, Nickel- und Kobaltlegierungen TechnischeLief

13、erbedingungen Teil 2: Vormaterial This European Standard was approved by CEN on 28 June 1990. CEN members are bound to comply with the requirements of the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any a

14、lteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tr

15、anslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemb

16、ourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN 1991 Copyright reserved to all CEN members Ref. No

17、. EN 2103-2:1991 EEN 2103-2:1991 BSI 12-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approva

18、l of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. According to the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece,

19、Iceland, Ireland, Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword 2 1 Scope and field of application 3 2 References 3 3 Manufacture 3 4 Dimensions and tolerances 3 5 Internal defects 3 6 External defects 3 7 Chemical composition 3 8 Num

20、ber of test samples 3 9 Mechanical testing 3 10 Special test 3 11 Marking 4 Table Summary of requirements for remelting stock 4EN 2103-2:1991 BSI 12-1999 3 1 Scope and field of application This standard specifies the particular requirements for remelting stock intended to be used for the manufacture

21、 of steel, nickel base or cobalt base alloy castings. This standard shall be used in conjunction with EN2103-1. 2 References EN 2002-1, Aerospace series Test methods for metallic materials Part 1: Tensile testing at ambient temperature 1) . EN 2002-2, Aerospace series Test methods for metallic mater

22、ials Part 2: Tensile testing at elevated temperature 1) . EN 2002-5, Aerospace series Test methods for metallic materials Part 5: Uninterrupted creep and rupture testing 2) . EN 2103-1, Aerospace series Steel, nickel base and cobalt base alloy remelting stock and castings Technical specification Par

23、t 1: General requirements. 3 Manufacture Remelting stock shall be manufactured from a melt consisting of: 1) pure materials and added elements, or 2) pure materials, added elements plus a defined and constant percentage of approved scrap, or 3) pure materials, added elements and approved scrap. Thei

24、r proportion per melt is at the option of the manufacturer. Unless otherwise specified on the order or manufacturing schedule, the manufacturing method3) shall be applied. 4 Dimensions and tolerances The form, mass, dimensions and tolerances of remelting stock shall be defined by agreement between t

25、he manufacturer and purchaser. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify compliance with the requirements. 5 Internal defects Remelting stock shall not contain defects prejudicial to its intended use. Unless otherwise agreed between the man

26、ufacturer and the purchaser and stated on the order or in the inspection schedule, test methods and acceptance criteria shall be at the option of the manufacturer. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify compliance with the requirements.

27、6 External defects Remelting stock shall be visually examined and shall be free from corrosion, scale, slag, grease or any other foreign matter including paint, other than that approved for marking. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify

28、 compliance with the requirements. 7 Chemical composition See EN2103-1. 8 Number of test samples Sufficient test samples shall be provided and prepared from each batch in accordance with the requirements of EN2103-1 for the tests required by the material standard or inspection schedule. 9 Mechanical

29、 testing Tensile test, creep rupture test, creep test required by the material standard shall be made at a frequency of one test per batch. Tensile testing at ambient temperature shall be carried out in accordance with EN2002-1. Tensile testing at elevated temperature shall be carried out in accorda

30、nce with EN2002-2. Creep and creep rupture testing shall be carried out in accordance with EN2002-5. Test results shall comply with the requirements of the material standard. 10 Special tests See EN 2103-1. For example: dross test, fracture test. 1) Published as AECMA pre-standard at the date of pub

31、lication of this standard. 2) In preparation at the date of publication of this standard.EN 2103-2:1991 4 BSI 12-1999 11 Marking 11.1 Unless otherwise specified on the order, all products shall bear the following identification marking: material standard number, melt number, identification of the ma

32、nufacturer and plant, such other marking as will ensure full identification. 11.2 Unless otherwise specified on the order, the method of marking shall be at the option of the manufacturer provided it is not prejudicial to the alloys quality and the marking is permanent. 11.3 The frequency of examina

33、tion adopted by the manufacturer shall be sufficient to permit him to certify compliance with the requirements. Table Summary of requirements for remelting stock Requirement Clause Product Inspection/Testing Method Standard Frequency Dimensions 4 All See 4 Internal defects 5 All See 5 See 5 External

34、 defects 6 All Visual See 6 Chemical composition 7 All 1 per batch Tensile properties at ambient temperature 9 When required Ambient temperature tensile test EN 2002-1 1 per batch Tensile properties at elevated temperature 9 When required Elevated temperature tensile test EN 2002-2 1 per batch Creep

35、 and creep rupture properties 9 When required Creep test EN 2002-5 1 per batch Special tests 10 When required See 10 Marking 11 All Visual See 11BSEN 2103-2:1992 BSI 12-1999 National appendix NA (informative) The United Kingdom participation in the preparation of this European Standard was entrusted

36、 by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/61 upon which the following bodies were represented: Aluminium Federation British Forging Industry Association British Investment Casting Trade Association British Steel Industry Copper Development Association Department

37、 of Trade (National Physical Laboratory) Light Metal Founders Association Ministry of Defence Society of British Aerospace Companies Limited National appendix NB (informative) The British Standard corresponding to the European Standard referred to in the text is as follows: There are no British Stan

38、dards corresponding to EN2002-1, EN2002-2 and EN2002-5, which are referred to in the text. It is envisaged that British Standards, identical in title and number, will be published in due course. European standard British Standard EN 2103-1 BS EN 2103 Steel, nickel base and cobalt base alloy remeltin

39、g stock and castings. Technical specification Part 1:1992 General requirements (Identical)BS EN 2103-2:1992 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in

40、 Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our pr

41、oducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers member

42、s an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In res

43、ponse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards throug

44、h its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standar

45、ds developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the pub

46、lications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written pe

47、rmission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.