BS EN 1514-4-1997 Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Corrugated flat or grooved metallic and filled metallic gaskets for use with steel fl.pdf

《BS EN 1514-4-1997 Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Corrugated flat or grooved metallic and filled metallic gaskets for use with steel fl.pdf》由会员分享，可在线阅读，更多相关《BS EN 1514-4-1997 Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Corrugated flat or grooved metallic and filled metallic gaskets for use with steel fl.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1514-4 : 1997 The E

2、uropean Standard EN 1514-4 : 1997 has the status of a British Standard ICS 23.040.80 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Flanges and their joints Dimensions of gaskets for PN-designated flanges Part 4. Corrugated, flat or grooved metallic and filled metallic gasket

3、s for use with steel flangesBS EN 1514-4 : 1997 This British Standard, having been prepared under the direction of the Sector Board for Engineering, was published under the authority of the Standards Board and comes into effect on 15 August 1997 BSI 1997 The following BSI references relate to the wo

4、rk on this standard: Committee reference PSE/2 Draft for comment 94/709822 DC ISBN 0 580 27688 0 Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PSE/2, Joint

5、ing materials and compounds, upon which the following bodies were represented: Asbestos Information Centre Ltd. British Adhesives and Sealants Association British Compressed Gases Association British Hydromechanics Research Group Chartered Institution of Water and Environmental Management Energy Ind

6、ustries Council Industrial Water Society L P Gas Association Water Services Association of England and WalesBS EN 1514-4 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 1514-4 3ii BSI 1997 BS EN 1514-4 : 1997 National foreword This

7、 Part of BS EN 1514 has been prepared by Technical Committee PSE/2, and is the English language version of EN 1514-4 : 1997 Flanges and their joints Dimensions of gaskets for PN-designated flanges Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges, pu

8、blished by the European Committee for Standardization (CEN). This Part of BS EN 1514 supersedes BS 4865 : Part 4 : 1989, which is withdrawn. Cross-references Publication referred to Corresponding British Standard EN ISO 6708 : 1995 BS EN ISO 6708 : 1996 Pipework components Definition and selection o

9、f DN (nominal size) Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committ

10、ee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN. All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1514-4 : 1997 E EUROPEAN STA

11、NDARD EN 1514-4 NORME EUROPE ENNE EUROPA ISCHE NORM April 1997 ICS 23.040.80 Descriptors: Industrial piping, flange connections, pipe joints, metal gaskets, gaskets, flat seals, pipe flanges, steels, dimensions, marking English version Flanges and their joints Dimensions of gaskets for PN-designated

12、 flanges Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges Brides et leurs assemblages Dimensions des joints pour les brides de signe es PN Partie 4: Joints me talliques ondule s, plats ou strie s et joints me talloplastiques pour brides en acier Fla

13、nsche und ihre Verbindungen Mae fu r Dichtungen fu r Flansche mit PN-Bezeichnung Teil 4: Dichtungen aus Metall mit gewelltem, flachem oder gekerbtem Profil fu r Stahlflansche This European Standard was approved by CEN on 1997-01-09. CEN members are bound to comply with the CEN/CENELEC Internal Regul

14、ations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Eu

15、ropean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the na

16、tional standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1514-4 : 1997 BSI 1997 Foreword This European Standard has been prepared by Technical Co

17、mmittee CEN/TC 74, Flanges and their joints, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1997, and conflicting national standards shall be with

18、drawn at the latest by October 1997. Annex A is informative and contains information to be supplied by the purchaser. Annex B is informative and contains A-deviations. EN 1514 consists of four Parts: Part 1: Specification for non-metallic flat gaskets with or without inserts Part 2: Specification fo

19、r spiral wound gaskets for use with steel flanges Part 3: Specification for non-metallic PTFE envelope gaskets Part 4: Specification for corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges According to the CEN/CENELEC Internal Regulations, the national standar

20、ds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 Intr

21、oduction 3 1 Scope 3 2 Normative references 3 3 Definitions 3 3.1 DN 3 3.2 PN 3 4 Designations 3 4.1 Range of PN designations 3 4.2 Range of DN (nominal sizes) 3 4.3 Gasket types 3 4.4 Information to be supplied by the purchaser 3 5 Gasket designs 3 6 Gasket types 5 7 Dimensions 5 8 Marking 5 Annexe

22、s A (informative) Information to be supplied by the purchaser 6 B (informative) A-deviation 6Page 3 EN 1514-4 : 1997 BSI 1997 Introduction WARNING. Gaskets made to this standard may contain asbestos. Materials containing asbestos may be subject to legislation that requires precautions to be taken wh

23、en handling them to ensure that they do not constitute a hazard to health (see annex B). Attention is drawn to relevant EEC directives. 1 Scope This European Standard specifies the dimensions and marking of IBC (inside bolt circle) corrugated, flat or grooved metallic and filled metallic gaskets for

24、 use in conjunction with flanges complying with prEN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100, up to and including DN 900. NOTE 1. Dimensions of other types of gaskets for use with flanges to prEN 1092-1, prEN 1092-2, prEN 1092-3 and prEN 1092-4 are given in EN 1514-1, EN 1514- 2 and

25、EN 1514-3. NOTE 2. Annex A lists information that should be supplied by the purchaser when ordering gaskets. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in

26、 the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred t

27、o applies. prEN 1092-1 Flanges and their joints Circular flanges for pipes, valves and fittings Part 1: Steel flanges PN designated prEN 1092-2 Flanges and their joints Part 2: Cast iron flanges prEN 1092-3 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories Part 3:

28、 Copper alloy and composite flanges PN designated prEN 1092-4 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories PN designated Part 4: Aluminium alloy flanges EN 1333 Pipework components Definition and selection of PN EN ISO 6708 Pipework components Definition and

29、selection of DN (nominal size) (ISO 6708 : 1995) 3 Definitions For the purposes of this standard the following definitions apply. 3.1 DN See EN ISO 6708. 3.2 PN See EN 1333. 4 Designations 4.1 Range of PN designations Gaskets shall be designated as suitable for use with one or more of the following

30、PN designations of flange: PN 10 PN 40 PN 16 PN 63 PN 25 PN 100 4.2 Range of DN (nominal sizes) Gasket nominal sizes shall be designated in accordance with the ranges specified in table 1. 4.3 Gasket types Gasket types as defined in clause 6 and illustrated in figure 1, shall be designated as: type

31、SC/A type CR/A type SC/B type CR/B type SC/C type CR/C type SC/D type CR/D type SC/E type CR/E 4.4 Information to be supplied by the purchaser NOTE. For information to be supplied by the purchaser, see annex A. 5 Gasket designs Gaskets shall be one of the designs shown in figure 1. NOTE. The selecti

32、on of the gasket should take into account the fluid, the operating conditions, the properties of the gasket materials, the type and surface finish of the flange facing and the flange bolt loading. It is recommended that selection of gaskets for any particular application is made in consultation with

33、 the gasket supplier (see annex A).Page 4 EN 1514-4 : 1997 BSI 1997 a) Corrugated metal, with filler (top) corrugated metal jacket with filler (bottom) (type - - -/A) c) Flat metal jacketed with filler (type - - - /C) b) Corrugated metal (type - - -/B) d) Grooved metal with or without a layer of add

34、itional gasket material (type - - -/D) e) Solid flat metal (type - - -/E) Figure 1. Corrugated, flat or grooved metallic and filled metallic gaskets a) self centring b) with centring ring NOTE. Type B, raised face flanges are shown. Figure 2. Gaskets for type A or type B flange facingsPage 5 EN 1514

35、-4 : 1997 BSI 1997 6 Gasket types Gaskets shall be for use with type A (flat face) or type B (raised face) flanges (see figure 2) and shall be one of the following types: a) self-centring, type SC/. (see 4.3); b) incorporating a centring ring, type CR/. (see 4.3). NOTE. Type A and type B flange faci

36、ngs are shown in prEN 1092-1. 7 Dimensions The dimensions of corrugated, flat or grooved metallic and filled metallic gaskets shall be as given in table 1. 8 Marking Gaskets shall be identified either individually or on the packaging containing the gasket(s) with the following information: a) the nu

37、mber and Part of this European Standard, i.e. EN 1514-4; b) gasket type designation (see 4.3); c) DN followed by the appropriate number (see table 1); d) PN designation (see table 1); NOTE. Certain gaskets may be suitable for more than one PN designation and may be suitably marked. e) materials; f)

38、manufacturers name or trademark. EXAMPLE: EN 1514-4, Type SC/C, DN 150, PN 63, XXX, AAA/BBB Table 1. Dimensions of corrugated, flat or grooved metallic and filled metallic gaskets Dimensions in millimetres DN Gasket inside diameter min. Gasket or centring ring outside diameter PN 10 PN 16 PN 25 PN 4

39、0 PN 63 PN 100 10 18 48 48 48 48 58 58 15 22 53 53 53 53 63 63 20 27 63 63 63 63 74 74 25 34 73 73 73 73 84 84 32 43 84 84 84 84 90 90 40 49 94 94 94 94 105 105 50 61 109 109 109 109 115 121 65 77 129 129 129 129 140 146 80 89 144 144 144 144 150 156 100 115 164 164 170 170 176 183 125 141 194 194 1

40、96 196 213 220 150 169 220 220 226 226 250 260 200 220 275 275 286 293 312 327 250 273 330 331 343 355 367 394 300 324 380 386 403 420 427 461 350 356 440 446 460 477 489 515 400 407 491 498 517 549 546 575 450 458 541 558 567 574 500 508 596 620 627 631 660 708 600 610 698 737 734 750 768 819 700 7

41、12 813 807 836 883 956 800 813 920 914 945 994 900 915 1020 1014 1045 1114 Page 6 EN 1514-4 : 1997 BSI 1997 Annex A (informative) Information to be supplied by the purchaser Before ordering a gasket it is recommended that the selection of the gasket design and type should be made in consultation wit

42、h the gasket supplier. The selection of gasket design and type should take account of the fluid, the operating conditions, the properties of the gasket material(s), type and surface finish of the flange facing and the flange bolt loading. The following information should be supplied by the purchaser

43、 when ordering gaskets: a) the number and Part of this European Standard, i.e. EN 1514-4; b) gasket design (see clause 5); c) gasket type (see clause 6); d) DN (see table 1); e) PN designation (see table 1); f) expected operating conditions for which the gasket will be used. Annex B (informative) A-

44、deviation This European Standard is mandated under the Council Directive on the approximation of the laws of the Member States concerning pressure equipment. A-deviation: national deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN/CENELEC me

45、mber. NOTE. (from CEN/CENELEC IR Part 2, 3.1.9): Where standards fall under EC Directives, it is the view of the Commission of the European Communities (OJ No G 59, 9.3.1982) that the effect of the decision of the Court of Justice in case 815/79 Cremonini/Vrankovich (European Court Reports 1980, p.

46、3583) is that compliance with A-deviations is no longer mandatory and that the free movement of products complying with such a standard should not be restricted except under the safeguard procedure provided for in the relevant Directive. A-deviations in an EFTA country are valid instead of the relev

47、ant provisions of the European Standard in that country until they have been removed. With reference to clause 5, gasket designs. Austria Order on the use of asbestos (BGBI. Nr 324/1990 Asbestverordnung). According to this order restrictions for trading, fabrication, use and marking of materials con

48、taining asbestos apply in Austria. Denmark Bekendtgrelse om asbest (Nr. 660 af 24. Juni 1986). Bekendtgrelse om aendring af bekendtgrelse om asbest (Nr. 139 af 23. Marts 1987) (Nr. 984 af 11. December 1992). According to this order, the use of asbestos and materials containing asbestos is prohibited

49、 in Denmark. France Decret n o 96-1132 du 24 Decembre 1996 modifiant le decret n o 96-98 du 7 Fevrier 1996 relatif a la protection des travailleurs contre les risques lies a linhalation de poussieres damiante. Decret n o 96-1133 du 24 Decembre 1996 relatif a linterdiction de lamiante, pris en application du code du travail et du code de la consommation. According to these regulations, within the scope of industrial safety the fabrication, manufacture, sale, import and merchandisi