BS CECC 75201-1992 Specification for harmonized system of quality assessment for electronic components - Blank detail specification - Interim example - Detail specification blank d.pdf

《BS CECC 75201-1992 Specification for harmonized system of quality assessment for electronic components - Blank detail specification - Interim example - Detail specification blank d.pdf》由会员分享，可在线阅读，更多相关《BS CECC 75201-1992 Specification for harmonized system of quality assessment for electronic components - Blank detail specification - Interim example - Detail specification blank d.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS CECC 75201:1992 Specification for Harmonized system of quality assessment for electronic components Blank detail specification Interim Example Detail Specification/Blank Detail Specification Circularconnectorsforfrequencies below 3 MHzBSCECC75201:1992 BSI 08-1999 ISBN 0 580 35257

2、 9 Amendments issued since publication Amd. No. Date CommentsBSCECC75201:1992 BSI 08-1999 i Contents Page National foreword ii Foreword iiBSCECC75201:1992 ii BSI 08-1999 National foreword This British Standard has been prepared under the direction of the Electronic Components Standards Policy Commit

3、tee (ECL/-). It is identical with CENELEC Electronic Components Committee (CECC)75201:1990 “Harmonized system of quality assessment for electronic components. Interim example detail specification/blank detail specification: Circular connectors for frequencies below3MHz” published by the European Com

4、mittee for Electrotechnical Standardization (CENELEC) Electronic Components Committee (CECC). CECC75201 was prepared by CECC Working Group25, LF Connectors, and the United Kingdom participation in the drafting was provided by sub-committee ECL/21/2, Connectors for electronic equipment. Scope. The st

5、andard provides the means for numbers to be allocated to detail specifications prepared in accordance with BSEN175200 and for their immediate publication. The Technical Committee has reviewed the provisions of CECC00400, to which reference is made in the text, and has decided that they are acceptabl

6、e for use in conjunction with this standard. The British Standard which implements the CECC Rules of Procedure is BS9000 “General requirements for a system for electronic components of assessed quality” Part2:1991 “Specification for the national implementation of the CECC System”. Detail specificati

7、on. Detail specifications shall comply with the requirements of this Blank Detail Specification and BSCECC00111 “Rule of Procedure11. Specifications”. Part4:1991 “Regulations for CECC Detail Specifications”. A British Standard does not purport to include all the necessary provisions of a contract. U

8、sers of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding British Standard CECC 75200:1985 together with Amendment 1 to CECC 75200:1985 b

9、ecame EN 175200:1991 BS EN 175200:1992 Harmonized system of quality assessment for electronic components: Sectional specification: Circular connectors for frequencies below3MHz (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theCECC title pa

10、ge, page ii and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinsidefrontcover.BSCECC75201:1992 ii BSI 08-1999 Foreword The CENELEC Electronic Components Committee (CECC) is composed of

11、those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and qua

12、lity assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate, of Conformity. The components produced under the System are thereby acceptable in all member countries without further testing. This specification has been formally approved

13、by the CECC, and has been prepared for those countries taking part in the System who wish to issue national harmonized specifications for CIRCULAR CONNECTORS FOR FREQUENCIES BELOW3MHz. It should be read in conjunction with the current regulations for the CECC System. At the date of printing of this

14、specification, the member countries of the CECC are Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom, and copies of it can be obtained from the addresses shown on the blue fly sheet. Preface This

15、 interim example detail specification/blank detail specification (EDS/BDS) was prepared by CECCWG25 “Low frequency connectors”. The object of producing this document in advance of a fully descriptive example detail specification is to establish the specification number for the EDS/BDS: Circular Conn

16、ectors for frequencies below3MHz. The publication of the number “CECC75201” provides the means for numbers to be allocated to detail specifications prepared in accordance with the provisions of CECC75200 and CECC00400 and for their immediate publication. It is intended that a future amendment to CEC

17、C75201 will provide a detailed EDS/BDS. The text of this EDS/BDS was circulated to the CECC for voting in the document indicated below and was ratified by the President of the CECC for printing as a CECC Specification. NOTEThis specification does not conform completely with the requirements of CECC0

18、0400. Document Date of Voting Report on the Voting CECC(Secretariat) 2391 June 1989 CECC(Secretariat) 2474blankBS CECC 75201:1992 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the U

19、K view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve

20、 the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967

21、400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. F

22、ax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internat

23、ional standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept u

24、p to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright,

25、 in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wit

26、hout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.