BS 8433-2004 Microwavable personal warmers - Specification《小型微波加热器 规范》.pdf

《BS 8433-2004 Microwavable personal warmers - Specification《小型微波加热器 规范》.pdf》由会员分享，可在线阅读，更多相关《BS 8433-2004 Microwavable personal warmers - Specification《小型微波加热器 规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 8433:2004 Microwavable personal warmers Specification ICS 97.100 BS 8433:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 24 June 2004 BSI 24 June 2004 The following BSI references relate to the work on this British St

2、andard: Committee reference PRI/68 Draft for comment 04/100949 DC ISBN 0 580 43923 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/68, Hot water bottles, upon which the following bodies were represented: British Ret

3、ail Consortium British Rubber Manufacturers Association Ltd. Co-opted members Consumer Policy Committee of BSI Department for Trade and Industry National Pharmaceutical Association RAPRA Technology Ltd.BS 8433:2004 BSI 24 June 2004 i Contents Foreword ii 1S c o p e 1 2 Normative references 1 3T e r

4、m s a n d d e f i n i t i o n s 1 4C o m p o s i t i o n 1 5 Performance requirements 2 6 Informative labelling 3BS 8433:2004 ii BSI 24 June 2004 Foreword This British Standard has been prepared by Technical Committee PRI/68. Attention is drawn to: a) the Toys (Safety) Regulations 1995 (UK Statutory

5、 Instrument SI 1995 No. 204) which is applicable to microwavable personal warmers which have any play value in the form of toys, or that include toys; b) the General Product Safety Regulations 1994 (UK Statutory Instrument SI 1994 No. 2328); c) 93/42/EEC, Council Directive concerning Medical Devices

6、. Council of European Communities. This British Standard calls for the use of substances and/or procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety

7、 at any stage. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front co

8、ver, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.BS 8433:2004 BSI 24 June 2004 1 1 Scope This British Standard specifies performance requirements and requir

9、ements for instructions for safe use for domestic microwavable personal warmers filled with a substance that has the characteristic of storing heat. This British Standard does not cover medical devices. NOTE Microwavable personal warmers may be used in the same way as hot water bottles. 2 Normative

10、references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. BS EN 71-1:2001, Safety of toys Part 1

11、: Mechanical and physical properties. BS EN 71-3:1995, Safety of toys Part 3: Migration of certain elements. (BS 5665-3:1995). BS EN 60335-2-25:1997, Specification for safety of household and similar electrical appliances Part 2-25: Particular requirements for microwave ovens. (IEC 60335-2-25:1996).

12、 3 Terms and definitions For the purposes of this British Standard, the following terms and definitions apply. 3.1 heatable medium substance that has the ability to store heat 3.2 microwavable personal warmer MPW product in its entirety designed to retain heat after being heated in a microwave oven

13、3.3 microwave oven microwave oven for normal domestic use, conforming to BS EN 60335-2-25:1997 3.4 normal use use as instructed in the manufacturers user instructions 3.5 primary cover envelope that retains the heatable medium 3.6 secondary cover additional covering that may be removable but part of

14、 the product in normal use 4 Composition When tested in accordance with BS EN 71-3:1995, the MPW shall not contain proportions (by mass) of migrateable elements in excess of the limits specified. None of the components shall be toxic. The components shall not contain extraneous matter. When the heat

15、able medium consists of plant materials, it shall not contain additives, toxic substances, pesticides or other contaminants that can affect human health. The MPW, including any secondary covers, shall not contain any metal components. NOTE Metallic materials should not be heated in microwave ovens d

16、ue to possible problems with arcing.BS 8433:2004 2 BSI 24 June 2004 5 Performance requirements 5.1 Microwavability The MPW shall be capable of being heated in a microwave oven. The MPW shall be capable of being heated from an ambient/cold state without the user having to undertake any other form of

17、action to reactivate it other than in accordance with the manufacturers instructions. When heating in accordance with the manufacturers instructions, the maximum temperature of the MPW shall not exceed 90 C at any point. 5.2 Accessibility 5.2.1 General The heatable medium shall be contained within t

18、he primary cover and shall not be accessible to the user. The MPW shall be tested in accordance with the test specified in 5.2.2. The MPW shall be tested in accordance with the tests specified in 5.2.3 or 5.2.4 as appropriate. 5.2.2 Determination of pressure resistance 5.2.2.1 Apparatus The apparatu

19、s shall have smooth upper and lower plates at least the size of the MPW. All contact edges of the plates shall have smooth edges of approximately three millimetres radius and free from any sharp corners. The apparatus shall be capable of cycling the upper plate to apply a load of between 0 kN and 0.

20、9 kN in not less than three seconds, dwelling at the maximum load for a minimum of three seconds, before returning to zero load in a minimum of three seconds and not less than five cycles per minute. 5.2.2.2 Procedure Place the MPW on the lower plate of the test apparatus. Perform the cycle for 500

21、cycles. On completion, examine the MPW for leakage or other detrimental effects. The MPW shall remain intact. 5.2.3 MPWs having pervious primary covers A leakage and tension test in accordance with BS EN 71-1:2001, 8.15 and 8.4.2.2 respectively shall be conducted. 5.2.4 MPWs having impervious primar

22、y covers A leakage test in accordance with BS EN 71-1:2001, 8.15 shall be conducted. 5.3 Heating performance 5.3.1 General During normal use, the MPW shall not emit toxic fumes, smoulder or burst into flames. No deposits shall be left in the microwave oven that could subsequently taint or contaminat

23、e food. 5.3.2 Determination of resistance to overheating 5.3.2.1 Heat the MPW in a microwave oven to twice the manufacturers recommended heating time on the highest setting of a 1 000 W microwave oven. The MPW shall remain intact and shall not emit fumes. The MPW shall be inspected after cooling and

24、 the heatable medium shall be contained.BS 8433:2004 BSI 24 June 2004 3 5.3.2.2 Complete five heating cycles in accordance with the manufacturers maximum heating times within a period of 30 s between each heating cycle on the high setting of a 1 000 W microwave oven. The MPW shall remain intact and

25、shall not emit toxic fumes. The MPW shall be inspected after cooling and the heatable medium shall be contained. NOTE 1 In practice, the only way evidence of overheating can be achieved is for the MPW to display indications that it has been overheated, i.e. clear visual evidence or strong olfactory

26、signals, thus making it obvious to the user that overheating has occurred. NOTE 2 Consideration should be given to having mandatory overheating warning indication such as the use of colour change inks or fabrics incorporated in the MPWs. NOTE 3 An element of overheating protection is vital for MPWs

27、of this nature as they will inevitably be overheated on some, if not many, occasions during their service life. This is particularly important considering that the elderly are a large target market for MPWs. However, because a microwave oven is an extremely powerful source of heating, it is consider

28、ed impossible to provide absolute protection and user awareness of the potential hazards is vital to ensure safety in use. 5.3.3 Pressure resistance Following determination of resistance to overheating (see 5.3.2), the MPW shall be tested again in accordance with the test specified in 5.2.2. 5.3.4 F

29、lammability Under no circumstances shall the MPW undergo combustion in the event of overheating; this shall be tested in accordance with 5.3.2. 6 Informative labelling 6.1 Product marking Each microwavable personal warmer shall be legibly and permanently marked or labelled (see 6.2) with the followi

30、ng, with a minimum font height of three millimetres for d), e) and f): a) number and date of this British Standard, i.e. BS 8433:2004 1) . b) date indication: year and month of manufacture; c) identification of the European manufacturer, or the UK distributor; d) the maximum recommended heating time

31、 and wattage in the format shown in Table 1; Table 1 Maximum recommended heating time and wattage NOTE # needs to be recommended by the manufacturer. e) “INSPECT AT REGULAR INTERVALS. DISCARD IF FOUND WORN OR DAMAGED”; f) “CLEAN ONLY IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS”. 6.2 Durability

32、 of marking 6.2.1 Procedure Rub the marking by hand for 15 s with a piece of cloth soaked with water and again for 15 s with a piece of cloth soaked with petroleum spirit. NOTE The petroleum spirit should be aliphatic solvent hexane having a maximum aromatics content of 0.1 % by volume, a Kauri-buta

33、nol value of 29, an initial boiling point of approximately 65 C, a dry point of approximately 69 C and a specific mass of approximately 0.66 kg/l. 6.2.2 Inspection After each test of this standard, the marking shall be inspected. The marking shall be clearly legible. All attached labels shall withst

34、and a tensile force of 90 N. 1) Marking BS 8433:2004 on or in relation to a product represents a manufacturers declaration of conformity, i.e. a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is solely the claimants respon

35、sibility. Such a declaration is not to be confused with third-party certification of conformity. RATING MAXIMUM TIME # # W # min # 1 000 W # min ONLY REHEAT FROM ROOM TEMPBS 8433:2004 4 BSI 24 June 2004 6.3 Accompanying instructions The following warnings shall be clearly displayed, with a minimum f

36、ont height of three millimetres, in the given format: “WARNING THIS PRODUCT CAN CAUSE BURNS. AVOID PROLONGED DIRECT CONTACT WITH THE SKIN TAKE CARE WHEN REMOVING FROM THE MICROWAVE OVEN DO NOT INGEST CONTENTS DO NOT OVERHEAT FOR MICROWAVE USE ONLY” The product shall be accompanied with full and comp

37、rehensive instructions for use, including instructions for: a) safe heating. The required heating times necessary to heat the product to its working temperature shall be provided. The times shall take into account the maximum available power of microwave ovens in normal domestic use; b) cleaning; c)

38、 safety advice in the event of overheating; d) safe disposal; e) identification of the European manufacturer, or the UK distributor; f) storage instructions. 6.4 Packaging/labelling Contents of the MPW shall be legible to the consumer at the point of sale. If a flexible film bag is used for packagin

39、g, the following warning shall be printed on the film in the format given: “PLASTIC BAGS CAN BE DANGEROUS TO AVOID DANGER OF SUFFOCATION KEEP THIS BAG AWAY FROM BABIES AND CHILDREN”. Where a part of the microwavable personal warmer contains natural rubber, both the accompanying instructions and thos

40、e permanently marked (see 6.2) on the product shall bear the clear and legible statement: “This microwavable personal warmer may contain natural rubber”. Where a part of the microwavable personal warmer contains latex rubber, both the accompanying instructions and those permanently marked (see 6.2)

41、on the product shall bear the clear and legible statement: “This microwavable personal warmer may contain latex rubber”.blankBS 8433:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It pr

42、esents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of

43、BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20

44、 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Cust

45、omer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British

46、 Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give detai

47、ls on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of th

48、ese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the

49、BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording