BS 4215-6-1987 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for electrode adaptors female taper 1 10《电阻点焊用电极、电极夹和辅助设备 第6部分 内锥度1 10的电.pdf

《BS 4215-6-1987 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for electrode adaptors female taper 1 10《电阻点焊用电极、电极夹和辅助设备 第6部分 内锥度1 10的电.pdf》由会员分享，可在线阅读，更多相关《BS 4215-6-1987 Resistance spot welding electrodes electrode holders and ancillary equipment - Specification for electrode adaptors female taper 1 10《电阻点焊用电极、电极夹和辅助设备 第6部分 内锥度1 10的电.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 4215-6: 1987 Incorporating Amendment No. 1 Resistance spot welding electrodes, electrode holders and ancillary equipment Part 6: Specification for electrode adaptors, female taper1 :10 ISO title: Resistance spot welding Electrode adaptors, female taper1 :10 UDC 621.791.763.1.037

2、+ 621.791.763.1.039BS4215-6:1987 This British Standard, having been prepared under the directionof the Welding Standards Committee, was published under the authority ofthe Board of BSI and comes intoeffect on 31 December 1987 BSI 10-1999 The following BSI references relate to the work on this standa

3、rd: Committee reference WEE/26 Draft for comment 83/76158 DC ISBN 0 580 16230 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Welding Standards Committee (WEE/-) to Technical Committee WEE/26, upon which the following bodies were repre

4、sented: Association of Supervisory and Executive Engineers British Non-ferrous Metals Federation British Steel Industry Copper Development Association Electricity Supply Industry in England and Wales Health and Safety Executive Institution of Electrical Engineers Ministry of Defence Society of Briti

5、sh Aerospace Companies Limited Society of Motor Manufacturers and Traders Limited Welding Institute Welding Manufacturers Association (BEAMA Ltd.) Coopted members Amendments issued since publication Amd. No. Date of issue Comments 7130 July 1992 Indicated by a sideline in the marginBS4215-6:1987 BSI

6、 10-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope and field of application 1 2 References 1 3 Dimensions 1 4 Designation 1 5 Material 2 6 Marking 2 Figure Electrode adaptor 1 Table Dimensions 1 Publications referred to Inside back coverBS4215-6:1987 ii BSI 10-199

7、9 Foreword This Part of BS 4215, prepared under the direction of the Welding Standards Committee, is based on ISO5829:1984, published by the International Organization for Standardization (ISO). It differs from the International Standard in specifying material that complies with BS4577 rather than I

8、SO5182, since the requirements for softening temperature in BS4577 are generally more stringent than those in ISO5182. This British Standard is being revised in several Parts and supersedes BS4215:1967, which is withdrawn. Most of the Parts will be identical with or based on International Standards

9、but, in instances where the UnitedKingdom was unable to give a vote of approval to the International Standard, a corresponding British Standard will be prepared, where possible, taking account of the reasons for disapproval. A further Part will also be published in due course, specifying electrodes,

10、 electrode holders and ancillary equipment of interest in the UK only. The following Parts of BS4215 have been published to date: Part 1: Withdrawn (superseded by BS EN25183-1:1992 and BS EN25183-2:1992); Part 2: Specification for straight resistance spot welding electrodes; Part 3: Withdrawn (super

11、seded by BS EN 21089:1992); Part 4: Withdrawn (superseded by BS EN 25822:1992); Part 5: Withdrawn (superseded by BS EN 25827:1992); Part 6: Specification for electrode adaptors, female taper1:10; Part 7: Specification for male electrode caps; Part 8: Withdrawn (superseded by BS EN 27931:1992); Part

12、9: Withdrawn (superseded by BS EN 25183-1:1992); Part 10: Withdrawn (superseded by BS EN 25183-2:1992); Part 11: Withdrawn (superseded by BS EN 28430-1:1992); Part 12: Withdrawn (superseded by BS EN 28430-2:1992); Part 13: Withdrawn (superseded by BS EN 28430-3:1992); Part 14: Withdrawn (superseded

13、by BS EN 29313:1992); Part 15: Specification for insulated pins for use in electrode back-ups. The text of ISO 5829:1984 has been used for ease of production of this Part of BS4215, although some terminology and certain conventions are not identical with those used in British Standards; attention is

14、 drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standard

15、s are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2, an inside back cover and a back cover. This standar

16、d has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS4215-6:1987 BSI 10-1999 1 1 Scope and field of application This Part of BS 4215 specifies the dimensions and tolerances of resistance spot weldi

17、ng electrode adaptors where the fixing element for the cap is a female taper (male electrode cap, see BS4215-7) and for which the electrode taper fits conform to BS EN21089:1992. 2 References The titles of the publications referred to in this standard are listed on the inside back cover. 3 Dimension

18、s The dimensions shall be those given in the Figure and the Table. Table Dimensions 4 Designation Electrode adaptors covered by this Part of BS4215 shall be designated by noting in order: a) the reference to this Part of BS4215; b) the external diameter, d 1 ; c) the length, l 1 . Example: Designati

19、on for an electrode adaptor with male cap, external diameter d 1= 16mm and length l 1=51mm: Electrode adaptor with male cap BS4215-6 16 51 a For information purposes only. Figure Electrode adaptor Dimensions in millimetres d 1 d 2 a d 3 a d 4 l 4 l 1 h11 0,5 for l 5 b= 31,5 40 50 63 80 16 15,5 11,8

20、8 20 32,5 41 51 64 81 a d 2and d 3are gauge dimensions at the taper reference line. b For information purposes only.BS4215-6:1987 2 BSI 10-1999 5 Material The material shall conform to code A 2/1 of BS4577. 6 Marking Electrode adaptors complying with this Part of BS 4215 shall be marked with the des

21、ignation laid down in clause4, but excluding the identity block and the reference number of this Part of BS4215, for example: 16 51BS4215-6:1987 BSI 10-1999 Publications referred to BS 4215, Resistance spot welding electrodes, electrode holders and ancillary equipment. BS 4215-7, Specification for m

22、ale electrode caps. BS 4577, Specification for materials for resistance welding electrodes and ancillary equipment. BS EN 21089:1992, Electrode taper fits for spot welding equipment Dimensions. ISO 5182, Materials for resistance welding electrodes and ancillary equipment 1) . ISO 5829, Resistance sp

23、ot welding Electrode adaptors, female taper 1 : 10 1) . 1) Referred to in the foreword only.BS 4215-6: 1987 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in

24、 Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our pr

25、oducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers member

26、s an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In res

27、ponse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards throug

28、h its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standar

29、ds developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the pub

30、lications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written pe

31、rmission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.