BS 4193-22-1996 Hardmetal insert tooling Classification and designation of approximate chip control zones for indexable inserts with chipbreakers《镶硬质合金刀具 第22部分 带断屑器的分度刀片近似切屑控制范围分类和.pdf
《BS 4193-22-1996 Hardmetal insert tooling Classification and designation of approximate chip control zones for indexable inserts with chipbreakers《镶硬质合金刀具 第22部分 带断屑器的分度刀片近似切屑控制范围分类和.pdf》由会员分享,可在线阅读,更多相关《BS 4193-22-1996 Hardmetal insert tooling Classification and designation of approximate chip control zones for indexable inserts with chipbreakers《镶硬质合金刀具 第22部分 带断屑器的分度刀片近似切屑控制范围分类和.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS 4193-22: 1996 ISO 10910: 1995 Hardmetal insert tooling Part 22: Classification and designation of approximate chip control zones for indexable inserts with chipbreakers ICS 25.100BS 4193-22:1996 This British Standard, having been prepared under the directionof the Engineering Sec
2、torBoard, was published underthe authority of the Standards Board and comes into effect on 15 September 1996 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference MTE/18 Draft for comment 92/74307 DC ISBN 0 580 26318 5 Committees responsible for this Briti
3、sh Standard The preparation of this British Standard was entrusted to Technical Committee MTE/18, Tools, tips and inserts for cutting applications, upon which the following bodies were represented: British Engineers Cutting Tools Association British Hardmetal Association Co-opted members Amendments
4、issued since publication Amd. No. Date CommentsBS 4193-22:1996 BSI 11-1998 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative references 1 3 Graph 1 4 Diagrams 1 5 Cutting test 1 6 Classification 3 Figure 1 2 Figure 2 4 List of references Inside back
5、 coverBS 4193-22:1996 ii BSI 11-1998 National foreword This British Standard has been prepared by Technical Committee MTE/18 and is identical with ISO 10910:1995 Classification and designation of approximate chip control zones for indexable inserts with chipbreakers, prepared by ISO/TC 29, Small too
6、ls, of the International Organization for Standardization (ISO). The Technical Committee has reviewed the provisions of ISO 683-1:1987, ISO3002-1:1982, ISO 3002-3:1984 and ISO 3685:1993 to which normative reference is made in the text, and has decided that they are acceptable for use in conjunction
7、with this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publi
8、cation referred to Corresponding British Standard ISO 1832:1991 BS 4193 Hardmetal insert tooling Part 1:1993 Specification for designation of indexable inserts for cutting tools (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, a
9、n inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.BS 4193-22:1996 BSI 11-1998 1 1 Scope This International Standard establishes a graph format used
10、 to develop diagrams depicting chipbreaker indexable insert performance. Performance results may be derived from the cutting test described in clause 5. Classification zones are established and coded in this International Standard. Suppliers of chipbreaker insert products may classify their products
11、 using the code of the zone within which the primary use of their product is indicated. It is important to acknowledge that the relationships established by diagrams developed according to this International Standard may vary from one work material to another, as well as with other machining variabl
12、es, and that it is not the purpose of this International Standard to serve as a specific guide to the practical application of chipbreaker insert products, but rather grant the user a sort of pre-selection, on a general level, that will allow him to look at only those items that have the best chance
13、 of satisfying his needs. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties t
14、o agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 683-1:1987, Heat-treatable steels, alloy st
15、eels and free-cutting steels Part 1: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products. ISO 1832:1991, Indexable inserts for cutting tools Designation. ISO 3002-1:1982, Basic quantities in cutting and grindingPart 1: Geometry of the active part of cutting t
16、ools General terms, reference systems, tool and working angles, chip breakers. ISO 3002-3:1984, Basic quantities in cutting and grindingPart 3: Geometric and kinematic quantities in cutting. ISO 3685:1993, Tool-life testing with single-point turning tools. 3 Graph The axes of the graph format (see F
17、igure 1) shall be the feed (according to ISO 3002-3) and the depth of cut (according to ISO 3002-3). The limits of the feed and depth of cut shall be = 0,025 mm/rev to 2,5 mm/rev and a p= 0,1 mm to 16 mm. 4 Diagrams The graph (see Figure 1) may be used to develop diagrams depicting chipbreaker inser
18、t performance resulting from the standard cutting test. The diagram shall be constructed by connecting points on the graph and shall represent an area within which chips are controlled. Referring to chips as acceptable and/or unacceptable is not recommended due to the varied opinions from industry t
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS4193221996HARDMETALINSERTTOOLINGCLASSIFICATIONANDDESIGNATIONOFAPPROXIMATECHIPCONTROLZONESFORINDEXABLEINSERTSWITHCHIPBREAKERS

链接地址:http://www.mydoc123.com/p-544223.html