ASTM F2891-2010 Standard Specification for Commercial Bulk Milk Dispensers Mechanically Refrigerated《商用牛奶定量分装机 机械冷藏的标准规范》.pdf

《ASTM F2891-2010 Standard Specification for Commercial Bulk Milk Dispensers Mechanically Refrigerated《商用牛奶定量分装机 机械冷藏的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2891-2010 Standard Specification for Commercial Bulk Milk Dispensers Mechanically Refrigerated《商用牛奶定量分装机 机械冷藏的标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2891 10Standard Specification forCommercial Bulk Milk Dispensers, MechanicallyRefrigerated1This standard is issued under the fixed designation F2891; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers commercial bulk milk dispens-ers which are for dispensing milk in the commercial andinstitutional f

3、ood service establishments. These commercialbulk milk dispensers are self-contained, manually-operated,gravity-fed, mechanically refrigerated cabinet(s) with lift-up orpush-type valves. These units are intended to dispense refrig-erated milk and fluid milk products.1.2 The values stated in inch-poun

4、d units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresp

5、onsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA167 Specification for Stainless and Heat

6、-ResistingChromium-Nickel Steel Plate, Sheet, and StripA176 Specification for Stainless and Heat-Resisting Chro-mium Steel Plate, Sheet, and StripA276 Specification for Stainless Steel Bars and ShapesA366/A366M Specification for Commercial Steel (CS)Sheet, Carbon (0.15 Maximum Percent) Cold-Rolled3D

7、3951 Practice for Commercial PackagingF760 Specification for Food Service Equipment ManualsF1166 Practice for Human Engineering Design for MarineSystems, Equipment, and Facilities2.2 ANSI Standards:4ANSI B1.1 Unified Inch Screw Threads (UN and UNRThread Form)ANSI Z1.4 Sampling Procedures and Tables

8、for Inspectionand AttributesANSI/UL 471 Commercial refrigerators and freezersNSF/ANSI 20 Commercial bulk milk dispensing equipment2.3 Military Standards:5MIL-STD-167/1 Mechanical Vibrations of ShipboardEquipment, Type IEnvironmental and Type IIInternally ExcitedMIL-STD-461 Military Standard for Elec

9、tromagnetic Emis-sion and Susceptibility Requirements for the Control ofElectromagnetic InterferenceMIL-STD-1399/300 Interface Standards for Shipboard Sys-tems Section 300A, Electric Power, Alternating Current3. Terminology3.1 Definitions of Terms Specific to This Standard:3.2 bulk food, nfood, avai

10、lable to the customer, which isnot enclosed in a sealed package, wrapper, or similar container.3.3 bulk milk dispenser, nequipment that consists ofmechanically refrigerated cabinet and a dispensing mechanismthat stores and dispenses servings of milk at proper tempera-tures when operated manually or

11、by machine actuation (otherthan coin).3.4 dispenser, na unit for storage and proportioned trans-fer of material such as beverages, condiments, food, soaps, orwares.4. Classification4.1 Commercial bulk milk dispensers cover by this specifi-cation are classified by type, electrical class and size.4.1.

12、1 Type:4.1.1.1 Type 1Table top unit.1This test method is under the jurisdiction of ASTM Committee F26 on FoodService Equipment and is the direct responsibility of Subcommittee F26.03 onStorage and Dispensing Equipment.Current edition approved Dec. 1, 2010. Published January 2011. DOI: 10.1520/F2891-

13、10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical s

14、tandard is referencedon www.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, Attn: NP

15、ODS ORAcquisition Streamlining and Standardization Information System (ASSIST) whichis the official source of all documents listed in the DoD Index of Specifications andStandards. The ASSIST can be located at http:/dodssp.daps.dla.mil.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700

16、, West Conshohocken, PA 19428-2959, United States.4.1.1.2 Type 1AStandard mounted with adjustable legs.4.1.1.3 Type 2AWith flange feet to allow the legs to bebolted to counter-top.4.1.1.4 Type 3ASealed to counter top.4.1.1.5 Type 4AWall mounted.4.1.2 Electrical Class:4.1.2.1 Class 1120 V, 60 Hz, 1 p

17、hase.4.1.2.2 Class 2230 V, 50 Hz, 1 phase.4.1.3 Size (Capacity)Number of Bulk Milk containersranging from 1 to 5 gal that can be dispensed from a singleunit.4.1.3.1 Size 11 milk container.4.1.3.2 Size 22 milk container.4.1.3.3 Size 33 milk container.4.1.3.4 This standard does not purport to address

18、all of thesizes that may be available but it provides an overview of themost common sizes used in the industry.5. Ordering Information5.1 Orders for commercial bulk milk dispensers in accor-dance with this specification shall include the followinginstructions:5.1.1 ASTM specification number and date

19、 issued,5.1.2 Quantity of units to be furnished,5.1.3 Type,5.1.4 Class,5.1.5 Size (Capacity).5.2 The following options should be reviewed, and ifdesired they should be also included in the order:5.2.1 When federal/military procurement(s) is involved,refer to the supplemental pages.5.2.2 When other t

20、han manufacturers standard, commer-cial, and domestic packaging is required, specify packagingrequirements.5.2.3 When special or supplemental requirements, or both,such as inspections, options, accessories, modifications,changes for correctional facilities use, additional nameplatedata, etc. are req

21、uired.5.2.4 When specified, a certification to ensure that samplesrepresenting each lot have been either tested or inspected asdirected and the requirements have been met. When specified,a copy of the certification or test results, or both, shall befurnished to the purchaser.5.2.5 When specified, a

22、number of dispensing heads needsto be specified during the ordering of the unit.5.2.6 When specified, the unit has a means to display orindicate cabinet temperature and able to set temperature.6. Materials and Manufacture6.1 GeneralCommercial bulk milk dispensers shall con-form to the applicable doc

23、uments listed in Section 2. Materialsused shall be free of defects that would affect the performanceor maintainability of individual components or of the overallassembly. Materials not specified herein shall be of the samequality used for the intended purpose in commercial practice.The use of used o

24、r rebuilt products is not allowed under thisspecification unless otherwise specified.6.2 Hardware and FittingsUnless otherwise specified, allhardware and fittings shall be corrosion-resistant to Specifica-tions A167 or A176 or suitably processed to resist corrosion inaccordance with the manufacturer

25、s standard practice.6.3 Threaded PartsAll threaded parts shall conform toANSI B1.1.7. Physical Properties7.1 Design and ManufacturerThe commercial bulk milkdispenser shall consist of a refrigerated cabinet, area physicallysupporting the refrigerated cabinet, area below refrigeratedcabinet for dispen

26、sing milk into a container, and provision tolimit the condensate drippings on the counter top. The com-mercial bulk milk dispenser may include product monitoringsystem, product probe, and bulk milk container holders toaccommodate various types of containers if specified.7.1.1 Cooling SystemThe cabin

27、et cooling system shouldbe contained in the unit so no accidental contact can be madewith moving parts.7.1.2 Controls:7.1.2.1 A temperature control must be provided for thecabinet.7.1.2.2 If specified, control functions such as data/information transfer ports (RS232), product-monitoring capa-bilitie

28、s, and water-resistant construction may be provided.7.1.3 AccessoriesIf specified, accessories such as built-intrim and locks shall be provided.7.2 Standards and ComplianceThe commercial bulk milkdispenser shall conform to the requirements of ANSI/UL 471and NSF/ANSI 20. Acceptable evidence of meetin

29、g thoserequirements shall be current listing mark, label, or symbol ofrecognized independent testing laboratory and a current listingin the testing laboratorys appropriate publication.7.2.1 Certification of compliance with the standards cited inthis specification shall be provided, if required, in t

30、he purchasedocument.8. Sampling and Quality Assurance8.1 When specified in the contact or purchase order, sam-pling, testing, and quality assurance of finished units shall beperformed in accordance with the requirements specified inANSI/UL 471 and NSF/ANSI 20.9. Product Marking9.1 Each commercial bu

31、lk milk dispenser shall be providedwith an identification plate or plates.10. Packaging and Package Marking10.1 Each commercial bulk milk dispenser shall be pack-aged and packed in accordance with the manufacturers stan-dard commercial domestic packaging. The package shall bemarked showing the name

32、of the product, model number, serialnumber, and manufacturers name. When specified, packagingshall be in accordance with the requirements of PracticeD3951.11. Instruction Materials and Manuals11.1 Each commercial bulk milk dispenser shall be finishedwith an instruction manual and material, as may be

33、 required.Manuals shall comply with Specification F760.F2891 10212. Keywords12.1 bulk milk dispenser; foodservice equipment; milkdispenserSUPPLEMENTARY REQUIREMENTSFEDERAL AND MILITARY PROCUREMENTThe supplemental requirements which follow apply to all Federal and Military procurements.Where provisio

34、ns of this supplement conflict with the main body, this supplement shall prevail.S1. ManualS1.1 A manual complying with Specification F760 andSupplement shall be provided.S2. First Article InspectionS2.1 When required, the first article inspection shall beperformed on one unit. The first article may

35、 be either a firstproduction or a standard production item from the supplierscurrent inventory, provided the item meets the requirements ofthe specification and is representative of the design, construc-tion, and manufacturing technique applicable to the remainingitems to be furnished under the cont

36、ract.S3. Label PlatesS3.1 Bulk milk dispensers shall be provided with data-nameplates and instruction plates.S3.1.1 Data-Name PlatesIn addition to the manufacturerdata plate, bulk milk dispensers shall be provided with data-name plates readily visible to the operator during normaloperating use and s

37、o as to not adversely affect the life andutility of the unit. Plates shall be attached to the front of theunit in such a manner as to meet the applicable NationalSanitation Foundation sanitary requirements for this equip-ment. The plate shall contain the following information, whichshall be stamped,

38、 engraved or applied by photosensitivemeans:S3.1.1.1 National Stock NumberS3.1.1.2 Government Approved Manual NumberS3.1.2 Instruction PlateAn instruction plate shall be madeof an ANSI/UL accepted label material and shall be attached tothe front of the bulk milk dispenser. The instruction plate shal

39、lbear instructions for start-up, operation, and shutdown.S4. Part Identifying NumberS4.1 The following part identifying numbering procedure isfor government purposes and does not constitute a requirementfor the contractor. These classes are the same as those inSection 4. The Pinsto be used for items

40、 acquired to thisASTMdocument are as follows:ASTM_-XX -XX -XX| | | |_ Size| | |_ Class| |_ Type|_ ASTM NumberS4.1.1 The above is an example of the PIN for an item inaccordance with ASTM Standard F_, type XX, class XX,and size XX.S5. Preservation, Packaging and Package MarkingS5.1 When other than nor

41、mal commercial practice or con-formance to Practice D3951 is desired, the preservation,packaging and package marking requirements shall be stated inthe purchase order or contract.S6. Human Factors CriteriaS6.1 Human factors engineering criteria principles andpractices, as defined in Practice F1166,

42、shall be used in thedesign of all bulk milk dispenser.S7. Manufacturers CertificationS7.1 If the manufacturer has successfully furnished thesame equipment on a previous contact within the past threeyears, further inspection will not be required. The manufacturershall certify in writing that the equi

43、pment to be furnished is thesame as that previously furnished and approved and that nomajor design changes have been made to the equipment.S8. Naval Shipboard RequirementsS8.1 Power CompatibilityUnless otherwise specified, alltypes of bulk milk dispensers shall operate on nominal 115Volt, single pha

44、se, 60 Hertz, 3-wire alternating current asspecified in MIL-STD-1399/300.S8.2 AccessBulk milk dispensers for naval surface vesselsshall be capable of passing through a 26 in. (660 mm) wide by66-in. (1676-mm) shipboard hatch without major disassembly.Dispensers for submarines shall pass through a 25-

45、in. (635-mm) diameter circular hatch. Major disassembly of a bulk milkdispenser intended for submarine use is permissible.S8.2.1 Service AccessWhen establishing accessibility re-quirements, both physical and visual access must be providedalong with access for any tools, test equipment or replacement

46、parts needed. All serviceable components shall be accessiblefrom the front of the unit.S8.3 MountingIf provided by the manufacturer, bulk milkdispensers shall be equipped with minimum 4 in. (102 mm)high stainless steel legs capable of mounting to a dresser. Whenlegs are not provided as part of the u

47、nit, bulk milk dispensersshall be provided with holes for mounting. The frame shall beprovided with four symmetrically spaced, drilled or threadedbosses or retaining nuts for this purpose. Mounting bolt sizeshall be38 in. (9.5 mm) minimum for dresser mounting. Bulkmilk dispensers shall be provided w

48、ith four type 300 seriesstainless steel round legs, each a minimum 1 in. (25.4 mm) indiameter, 4 in. (102 mm) in length, for securing dispenser todresser.F2891 103S8.4 Environmental SuitabilityBulk milk dispensers shallbe capable of withstanding ships vibration and motion. Con-trols, switches, movin

49、g parts, and electrical circuits shalloperate under shipboard conditions without malfunction, bind-ing, excessive looseness, or damage. (See S8.6.3.)S8.5 Inclined OperationBulk milk dispensers shall oper-ate satisfactorily on surface ships when inclined at an angle of15 each side of the vertical in each of two vertical planes atright angles to each other, with no spillage of fluid or product.For submarines the angle of inclination shall be 30.S8.6