ASTM F2252-2013 Standard Practice for Evaluating Ink or Coating Adhesion to Flexible Packaging Materials Using Tape《使用胶带评价柔性包装材料与墨水和涂层间粘性的标准实施规程》.pdf

《ASTM F2252-2013 Standard Practice for Evaluating Ink or Coating Adhesion to Flexible Packaging Materials Using Tape《使用胶带评价柔性包装材料与墨水和涂层间粘性的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2252-2013 Standard Practice for Evaluating Ink or Coating Adhesion to Flexible Packaging Materials Using Tape《使用胶带评价柔性包装材料与墨水和涂层间粘性的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2252 13Standard Practice forEvaluating Ink or Coating Adhesion to Flexible PackagingMaterials Using Tape1This standard is issued under the fixed designation F2252; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes a means of evaluating ink orcoating adhesion to flexible packaging materials. This prac

3、ticeis intended for use on flexible packaging materials whosesurfaces are not damaged by the application and removal oftape.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore,

4、eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2D3330/D3330M Test Method for PeelAdhesion of Pressure-Sensitive TapeE171 Practice for Conditioning and Testing Flexible

5、BarrierPackaging3. Significance and Use3.1 Poor adhesion of ink or coating to the base substrate canimpact the readability of printed materials, affect the function-ality of coated materials, or create a source of contamination.This practice provides a means for evaluating the adhesion ofink or coat

6、ing to a flexible packaging material.3.2 For purposes of resolving inter-laboratorydisagreements, test methods developed from this practice maybe improved by defining and controlling the pressure andmethod of tape application, (for example, using weightedroller), and the speed and angle of tape remo

7、val.3.3 This practice does not address acceptability criteria.These need to be jointly determined by the user and producerof the product.4. Apparatus4.1 3M #610 or Sellotape office adhesive tape is commonlyused for this procedure, typically 19 to 25 mm (34 to 1 in.)wide. Whichever tape is chosen sho

8、uld be agreed upon bycustomer and supplier.4.1.1 Manufacturers storage and shelf-life recommenda-tions should be followed or acceptability determined throughreal-time aging and laboratory tests. Test Method D3330/D3330M gives guidance on testing. Again, as stated in 3.3,acceptability criteria is a m

9、atter of agreement between cus-tomer and supplier.5. Sampling5.1 The number of samples tested should be adequate to bepredictive of performance. Caution should be taken wheneliminating samples with defects as this can bias results.6. Conditioning6.1 Conditioning of the samples will depend on the mat

10、erialunder evaluation. If conditioning before testing is appropriate,normal, and desirable, refer to E171 for guidance.6.2 Before testing catalyzed or cured inks or coatings, orboth, ensure that the samples have been exposed to theappropriate conditions for sufficient time to allow completecure.7. P

11、rocedure7.1 Lay sample to be tested on a flat surface. Sample shouldlay flat and smooth without wrinkles, creases, or folds.7.2 Cut a piece of tape long enough to cover the printed orcoated area of interest on the sample. For large areas it may beeasier to work with several shorter pieces of tape. H

12、andlingapplication and removal of tape is simpler when length of tapedoes not exceed 12 in.7.3 Apply tape to sample using a smooth even motionwithout wrinkling tape or sample. Run thumb or forefingeralong tape to make sure it is fully adhered, without any bubblesin surface.1This practice is under th

13、e jurisdiction of ASTM Committee F02 on FlexibleBarrier Packaging and is the direct responsibility of Subcommittee F02.20 onPhysical Properties.Current edition approved May 1, 2013. Published June 2013. Originallyapproved in 2003. Last previous edition approved in 2008 as F2252 03 (2008).DOI: 10.152

14、0/F2252-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Driv

15、e, PO Box C700, West Conshohocken, PA 19428-2959. United States17.4 Hold sample flat to surface with one hand, use otherhand to peel back tape at an angle of approximately 120 to150. Lift tape, pulling back with an even, moderate motion.Typically 305 to 460 mm (12 to 18 in.) per second.NOTE 1Varying

16、 the amount of time after tape is applied may affect theresults.7.5 Examine the test sample for missing print or coatinggaps.7.6 Examine tape for any ink or coating removed from thetest sample. As an aid for visual inspection reference standardsmay be created and used to determine degree of transfer

17、.7.7 Record results. Characterize the degree of adhesionusing mutually agreed upon references. If multiple colors ofink are present, results may vary by color and may be reportedthat way. This is a subjective test and operator training iscrucial for consistent reporting of test results.8. Keywords8.

18、1 adhesion; anchorage; coating; ink; print; tape testASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent ri

19、ghts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either fo

20、r revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearin

21、g you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2252 132