ASTM E927-2010(2015) 3893 Standard Specification for Solar Simulation for Photovoltaic Testing《大地光电测试用阳光模拟的标准规范》.pdf

《ASTM E927-2010(2015) 3893 Standard Specification for Solar Simulation for Photovoltaic Testing《大地光电测试用阳光模拟的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM E927-2010(2015) 3893 Standard Specification for Solar Simulation for Photovoltaic Testing《大地光电测试用阳光模拟的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E927 10 (Reapproved 2015)Standard Specification forSolar Simulation for Photovoltaic Testing1This standard is issued under the fixed designation E927; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides means for classifying solarsimulators intended for indoor testing of photovoltaic devices(solar c

3、ells or modules), according to their spectral match to areference spectral irradiance, non-uniformity of spatialirradiance, and temporal instability of irradiance.1.2 Testing of photovoltaic devices may require the use ofsolar simulators. Test Methods that require specific classifica-tion of simulat

4、ors as defined in this specification include TestMethods E948, E1036, and E1362.1.3 This standard is applicable to both pulsed and steadystate simulators and includes recommended test requirementsused for classifying such simulators.1.4 A solar simulator usually consists of three major com-ponents:

5、(1) light source(s) and associated power supply; (2)any optics and filters required to modify the output beam tomeet the classification requirements in Section 4; and (3) thenecessary controls to operate the simulator, adjust irradiance,etc.1.5 A light source that does not meet all of the definedreq

6、uirements for classification presented in this document maynot be referred to as a solar simulator.1.6 Spectral irradiance classifications are provided for AirMass 1.5 direct and global (as defined in Tables G173), or AirMass 0 (AM0, as defined in Standard E490).1.7 The classification of a solar sim

7、ulator is based on thesize of the test plane; simulators with smaller test plane areashave tighter specifications for non-uniformity of spatial irradi-ance.1.8 The data acquisition system may affect the ability tosynchronize electrical measurements with variations in irradi-ance and therefore may be

8、 included in this specification. In allcases, the manufacturer must specify with the temporal insta-bility classification: (1) how the classification was determined;and (2) the conditions under which the classification wasdetermined.1.9 The classification of a solar simulator does not provideany inf

9、ormation about electrical measurement errors that arerelated to photovoltaic performance measurements obtainedwith a classified solar simulator. Such errors are dependent onthe actual instrumentation and procedures used.1.10 The values stated in SI units are to be regarded asstandard. No other units

10、 of measurement are included in thisstandard.1.11 The following precautionary caveat pertains only to thehazards portion, Section 6, of this specification. This standarddoes not purport to address all of the safety concerns, if any,associated with its use. It is the responsibility of the user of thi

11、sstandard to establish appropriate safety and health practicesand determine the applicability of regulatory requirementsprior to use.2. Referenced Documents2.1 ASTM Standards:2E490 Standard Solar Constant and Zero Air Mass SolarSpectral Irradiance TablesE772 Terminology of Solar Energy ConversionE94

12、8 Test Method for Electrical Performance of Photovol-taic Cells Using Reference Cells Under Simulated Sun-lightE1036 Test Methods for Electrical Performance of Noncon-centrator Terrestrial Photovoltaic Modules and ArraysUsing Reference CellsE1328 Terminology Relating to Photovoltaic Solar EnergyConv

13、ersion (Withdrawn 2012)3E1362 Test Method for Calibration of Non-ConcentratorPhotovoltaic Secondary Reference CellsG138 Test Method for Calibration of a SpectroradiometerUsing a Standard Source of Irradiance1This specification is under the jurisdiction of ASTM Committee E44 on Solar,Geothermal and O

14、ther Alternative Energy Sources and is the direct responsibility ofSubcommittee E44.09 on Photovoltaic Electric Power Conversion.Current edition approved Nov. 1, 2015. Published November 2015. Originallyapproved in 1983. Last previous edition approved in 2010 as E927 10. DOI:10.1520/E0927-10R15.2For

15、 referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referen

16、ced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1G173 Tables for Reference Solar Spectral Irradiances: DirectNormal and Hemispherical on 37 Tilted Surface2.2 IEC Standard:IEC 60904-9 Photovoltaic DevicesPart 9: Solar

17、 SimulatorPerformance Requirements3. Terminology3.1 DefinitionsDefinitions of terms used in this specifica-tion may be found in Terminologies E772 and E1328.3.2 Definitions of Terms Specific to This Standard:3.2.1 solar simulatorequipment used to simulate solarradiation. Solar simulators shall be la

18、beled by their mode ofoperation during a test cycle (steady state, single pulse ormulti-pulse) and by the size of the test plane area. A solarsimulator must fall into at least the C classification.3.2.2 simulator classificationa solar simulator may be oneof three classes (A, B, or C) for each of thr

19、ee categories:spectral match, spatial non-uniformity, and temporal instabil-ity. The simulator is rated with three letters in order of spectralmatch, spatial non-uniformity and temporal instability (forexample: ClassABA). Large area and small area simulators areclassified according to the appropriat

20、e table. The simulatorclassification may be abbreviated by a single letter character-ization.Asimulator characterized by a single letter is indicativeof a simulator with all three classes being the same (forexample: a Class A simulator is the same as a Class AAAsimulator).3.2.3 test plane area, Athe

21、 area of the plane intended tocontain the device under test.3.2.4 small area solar simulatora simulator whose testplane is equal to or less than 30 cm by 30 cm or a diameter ofless than 30 cm if the test area is circular.3.2.5 large area solar simulatora simulator whose testplane is greater than 30

22、cm by 30 cm or a diameter of greaterthan 30 cm if the test area is circular.3.2.6 steady-state simulatora simulator whose irradianceoutput at the test plane area does not vary more than 5 % fortime periods of greater than 100 ms.3.2.7 single-pulse simulatora simulator whose irradianceoutput at the t

23、est plane area consists of a short duration lightpulse of 100 ms or less.3.2.8 multi-pulse simulatora simulator whose irradianceoutput at the test plane area consists of a series of shortduration, periodic light pulses. Note that the light pulses do notnecessarily have to go to zero irradiance betwe

24、en pulses; asteady-state simulator that fails the 5 % requirement in 3.2.6can be classified as a multi-pulse simulator if the irradiancevariations are periodic.3.2.9 time of data acquisitionthe time required to obtainone data point (irradiance, current, and voltage) if there is asimultaneous measure

25、ment of irradiance at each current-voltage data point. If no simultaneous measurement of theirradiance is made during the test, the time of data acquisitionis the time to obtain the entire current-voltage (I-V) curve.3.2.10 solar spectrumthe spectral distribution of sunlightat Air Mass 1.5 Direct (a

26、s defined in Tables G173), Air Mass1.5 Global (as defined in Tables G173), or Air Mass 0 (asdefined in Standard E490).3.2.11 spectral matchratio of the actual percentage oftotal irradiance to the required percentage specified in Table 3for each wavelength interval.3.2.12 spatial non-uniformity of ir

27、radiance (in percent):SNE5 100% 3Emax2 EminEmax1Emin(1)where Emaxand Eminare measured with the detector(s) overthe test plane area.3.2.13 temporal instability of irradiance (in percent):TIE5 100% 3Emax2 EminEmax1Emin(2)where Emaxand Eminare measured with the detector at anyparticular point on the te

28、st plane during the time of dataacquisition.3.2.14 field of viewthe maximum angle between any twoincident irradiance rays from the simulator at an arbitrary pointin the test plane.4. Significance and Use4.1 In any photovoltaic measurement, the choice of simula-tor Class should be based on the needs

29、of that particularmeasurement. For example, the spectral distribution require-ments need not be stringent if devices of identical spectralresponse from an assembly line are being sorted according tocurrent at maximum power, which is not a strong function ofspectral distribution.4.2 Classifications o

30、f simulators are based on the size of thetest area and the probable size of the device being measured. Ithas been shown that when measuring modules or other largerdevices the spatial non-uniformity is less important, and up to3 % non-uniformity may not introduce unacceptable error forsome calibratio

31、n procedures.4Accurate measurements ofsmaller area devices, such as cells, may require a tighterspecification on non-uniformity or characterization of thenon-uniformity by the user. When measuring product it isrecommended that the irradiance be measured with a referencedevice similar to the devices

32、that will be tested on the simulatorto minimize spatial non-uniformity errors.4Herrman, W., and Wiesner, W., “Modelling of PV ModulesThe Effects ofNon-Uniform Irradiance on Performance Measurements with Solar Simulators,”Proc. 16th European Photovoltaic Solar Energy Conf., European Commission,Glasgo

33、w, UK, 2000.TABLE 1 Classification of Small Area Simulator PerformanceClassificationCharacteristicsSpectralMatchto all IntervalsSpatial Non-uniformityof IrradianceTemporalInstabilityofIrradianceClass A 0.75 to 1.25 2 % 2 %Class B 0.6 to 1.4 5 % 5 %Class C 0.4 to 2.0 10 % 10 %E927 10 (2015)24.3 It is

34、 the intent of this specification to provide guidanceon the required data to be taken, and the required locations forthis data to be taken. It is not the intent to define the possiblemethods to measure the simulator spectrum or the irradiance atevery location on the test plane.4.4 Note that the lett

35、er classification scheme (see 3.2.2) doesnot include a number of important properties, especially thetest plane size, the field of view, nor the steady state or thepulsed classifications (see 3.2.3 through 3.2.8, and 3.2.14).These additional properties are included in the reportingrequirements (see

36、Section 9). It is also recommended that theybe included in product specification sheets or advertising.4.5 Because of the transient nature of pulsed solarsimulators, considerations must be given to possible problemssuch as the response time of the device under test versus thetime of data acquisition

37、 and the rise time of the pulsedirradiance. If a pulsed solar simulator includes a data acquisi-tion system, the simulator manufacturer should provide guid-ance concerning such possible problems that may affect mea-surement results on certain test devices.4.6 The simulator manufacturer should provid

38、e I-V datashowing the repeatability of multiple measurements of a singledevice. This data should include a description of how therepeatability was determined.5. Classification5.1 A solar simulator may be either steady state or pulsed,and its performance for each of three determined categories(spectr

39、al match, spatial non-uniformity, and temporal instabil-ity) may be one of three Classes (A, B, or C). A simulator maybe classified to multiple Classes, depending on its characteris-tics in each of the performance categories. For example, asimulator may be Class A related to spatial uniformity andCl

40、ass B related to spectral distribution. Classification for allthree performance characteristics must be defined and providedby the manufacturer.5.2 The manufacturer shall provide test area information toassist in proper usage of the simulator. Tables 1 and 2 giveperformance requirements for small an

41、d large area simulatorsfor the three performance categories: spectral match to thereference spectrum at all intervals, non-uniformity ofirradiance, and temporal instability of irradiance. Table 3 givesthe spectral match requirements for spectral distribution ofirradiance for Direct AM1.5, Global AM1

42、.5, and AM0. Thesimulator irradiance is divided into the same wavelengthintervals and compared with the reference spectrum. Allintervals must agree within the spectral match ratio in Table 1to obtain the respective Class.5.3 A reference device should be used for determining thespatial uniformity of

43、the simulator. The reference device musthave a spectral response appropriate for the simulator; a silicondevice is typically a good choice. A map of simulator spatialuniformity must be supplied with the simulator to assist theuser in simulator operation and to clearly define different areasin the te

44、st plane that may have different classifications.5.4 For the evaluation of temporal instability, the dataacquisition system may be considered an integral part of thesolar simulator. When the data acquisition system of the solarsimulator measures data simultaneously (irradiance, voltage,and current d

45、ata measured within 10 nanoseconds of eachother), then the temporal instability may be rated A for thisclassification but the range of irradiance variation during anentire I-V measurement, including times between points, mustbe reported and less than 5 %. If a solar simulator does notinclude the dat

46、a acquisition system, then the simulator manu-facturer must specify the time of data acquisition as related tothe reported temporal instability classification.5.4.1 For a steady-state simulator without an integral dataacquisition system this rating must be given for a period of 1second, and actual i

47、nstability data must be reported for 100milliseconds, 1 minute, and 1 hour.5.4.2 In the case of a pulsed solar simulator with a dataacquisition system that measures irradiance, current, and volt-age sequentially, temporal instability must be evaluated.5.4.3 The user of a pulsed simulator should veri

48、fy that thedevice under test has reached final electrical output levels whendata acquisition has begun and that the device under test has afast enough response to follow the rapidly-changing irradiance.5.4.4 The ultimate test of the stability of the simulator andsystem is the actual measurement of d

49、ata on the total system.For simulators that include an integral data acquisition system,a repeatability measurement should be made on the significantmeasured parameters such as voltage, fill factor, and current toverify the correction being applied on each data pair isrepeatable from measurement to measurement. The manufac-turer should specify how repeatability was measured and reportthe results.6. Hazards6.1 The use of a solar simulator involves several safetyhazards. A partial description of potential hazards follows:TABLE 2 Classification of Large Area Simulator Pe