ASTM E1425-2007 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗、门、天窗和玻璃墙设施传声性能的标准实施规程》.pdf

《ASTM E1425-2007 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗、门、天窗和玻璃墙设施传声性能的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1425-2007 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗、门、天窗和玻璃墙设施传声性能的标准实施规程》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 1425 07Standard Practice forDetermining the Acoustical Performance of Windows,Doors, Skylight, and Glazed Wall Systems1This standard is issued under the fixed designation E 1425; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice establishes requirements for testing andrating acoustical performance of window,

3、 door, skylight, andglazed wall systems, regardless of their method or materials ofmanufacture.1.1.1 Operating force, latching force, and air leakage areintegral elements of the acoustical performance of window,door, skylight, and glazed wall systems. This practice requires(when applicable) the conc

4、urrent testing of operating force,latching force, and air leakage, in addition to the soundtransmission loss test.1.2 This practice establishes the test methodology, specimencriteria, and classification rating system for purposes of deter-mining the acoustical performance levels of window, door,skyl

5、ight, and glazed wall systems only, and not throughopenings between such assemblies and adjacent construction.1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety co

6、ncerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 634 Terminology Relating to Buildin

7、g and Environmen-tal AcousticsE90 Test Method for Laboratory Measurement of AirborneSound Transmission Loss of Building Partitions and Ele-mentsE 283 Test Method for Determining Rate of Air LeakageThrough Exterior Windows, Curtain Walls, and DoorsUnder Specified Pressure Differences Across the Speci

8、menE 413 Classification for Rating Sound InsulationE 631 Terminology of Building ConstructionsE 1332 Classification for Determination of Outdoor-IndoorTransmission ClassE 2068 Test Method for Determination of Operating Forceof Sliding Windows and Doors2.2 Other Standards:28 CFR Part 36 ADA Standards

9、 for Accessible Design3AAMA/WDMA/CSA 101/I.S.2/A440 Standard Specifica-tion for Windows, Doors, and Unit Skylights4,5AAMA 501 Methods of Tests for Exterior Walls4NFRC 100 Procedure for Determining Fenestration ProductU Factors6ISO 140 AcousticsMeasurement of sound insulation inbuildings and of build

10、ing elements73. Terminology3.1 DefinitionsFor definitions of terms used in this prac-tice, refer to Terminologies C 634 and E 631, unless otherwiseindicated.4. Significance and Use4.1 Air Leakage Relative to Sound TransmissionCertainfrequencies are more susceptible to sound transmission throughcavit

11、ies or discontinuities in the test specimen; therefore, theair leakage of the test specimen is reported to allow theapproving authority information relative to air tightness.NOTE 1The AAMA/WDMA/CSA 101/I.S.2/A440 document pro-vides air leakage acceptance criteria for these products based on their1Th

12、is practice is under the jurisdiction of ASTM Committee E06 on Perfor-mance of Buildings and is the direct responsibility of Subcommittee E06.51 onPerformance of Windows, Doors, Skylights and Curtain Walls.Current edition approved Oct. 1, 2007. Published November 2007. Originallyapproved in 1991. La

13、st previous edition approved in 1999 as E 1827 91 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Ava

14、ilable from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4Available from the American Architectural Manufacturers Association(AAMA), 1827 Walden Office Square, Suite 550, Schaumburg, Illinois 60173-4268.5Ava

15、ilable from Canadian Standards Association (CSA), 5060 Spectrum Way,Mississauga, ON L4W 5N6, Canada, http:/www.csa.ca.6Available from the National Fenestration Rating Council (NFRC), 6305 IvyLane, Suite 140 Greenbelt, MD 20770.7Available from International Organization for Standardization (ISO), 1 r

16、ue deVaremb, Case postale 56, CH-1211, Geneva 20, Switzerland, http:/www.iso.ch.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.performance class. Acoustical products could require a lower air leakagerate than what is required in thi

17、s standard in order to achieve the desiredacoustical performance.4.2 Operating Force Relative to Sound TransmissionTheuse of specific sealing components to achieve a given soundrating could affect operating force of the vertical or horizontalsliding sash or panels of the assembly; therefore, operati

18、ngforce is reported to allow the approving authority informationrelative to sash or panel operating forces.NOTE 2The opening force in 28 CFR Part 36 ADA for interior hingeddoors and sliding doors is limited to 22.2 N (5 lbf). The AAMA/WDMA/CSA 101/I.S.2/A440 document provides operating force accepta

19、nce cri-teria for products based on their performance class.4.3 Latching force Relative to Sound TransmissionLatching force can affect the compression of seals and theamount of damping applied to the system that in turn affects theair leakage and the acoustical performance. The use of specificsealin

20、g components and latching/locking hardware can affectthe force required to close and latch the door under test. Thelatching force is reported to allow the approving authorityinformation relative to sash or panel latching conditions.NOTE 3The AAMA/WDMA/CSA 101/I.S.2/A440 document statesthat the latch

21、ing force shall not exceed 65 N (15 lbf).5. Test Specimen5.1 Assemblies to be tested in accordance with this practiceshall be representative of those produced by the manufactureror fabricator. Test specimens shall be sealed, painted orotherwise finished or prepared only as they would normally beprep

22、ared for actual installation and use. Test specimens shall bemounted for testing as specified by each applicable testmethod.5.1.1 Test specimens shall not be modified with supplemen-tary adhesives, sealants, tapes, or clamping devices not nor-mally a part of the product.5.2 The test specimen size fo

23、r window, door, skylight, andglazed wall systems are listed below in Table 1. The window,sliding door, glazed wall system, sloped glazing system,skylight, and roof window test specimen size shall not vary bymore than 25 mm (i in.) for either dimension. The single andTABLE 1 Test Specimen SizeWindow

24、Descriptions Width (mm) 3 Height (mm) Width (in.) 3 Height (in.)basement window 900 3 600 35.4 3 23.6casement window 600 3 1500 23.6 3 59.1compositefixed beside operable 1500 3 1200 59.1 3 47.2compositefixed over/under operable 1200 3 1500 47.2 3 59.1dual action window (tilt/turn window) 1200 3 1500

25、 47.2 3 59.1fixed window (picture window) 1200 3 1500 47.2 3 59.1greenhouse/garden window 900 3 900 3 300 35.4 3 35.4 3 11.8horizontal sliding window 1500 3 1200 59.1 3 47.2jalawning window 1200 3 1500 47.2 3 59.1jalousie window 1200 3 1500 47.2 3 59.1pivoted window (vertical or horizontal) 1200 3 1

26、500 47.2 3 59.1projected window (awning or hopper) 1500 3 600 59.1 3 23.6side-hinged window 1200 3 1500 47.2 3 59.1top-hinged window 1200 3 1500 47.2 3 59.1vertical sliding (single, double, and triple hung) window 1200 3 1500 47.2 3 59.1Door Descriptions and Required Elementssingle swinging (hinged)

27、 door 1000 3 2125 39.4 3 83.7double swinging (hinged) door 1900 3 2125 74.8 3 83.7sliding door 1825 3 2025 71.9 3 79.7sidelites 600 3 2000 23.6 3 78.7transoms 2000 3 600 78.7 3 23.6Glazed Wall System Descriptionscurtain walls, storefront, and so forth. 2000 3 2000 78.7 3 78.7sloped glazing system 20

28、00 3 2000 78.7 3 78.7Skylight Descriptionsunit skylights 1200 3 1200 47.2 3 47.2roof windows 1200 3 1200 47.2 3 47.2NOTE 1The area used to calculate the sound transmission loss of the window, door, skylight, or glazed wall assembly shall include the test specimenframe.NOTE 2For a more thorough descr

29、iption of the window and door types, refer to The AAMA/WDMA/CSA 101/I.S.2/A440 document.NOTE 3The window sizes listed above were taken primarily from NFRC 100 and AAMA/WDMA/CSA 101/I.S.2/A440 standards with somemodifications due to the inconsistencies between the two documents. Some consideration wa

30、s also given to the size (1250 mm 3 1500 mm 6 50 mm)recommended in the ISO 140 standard.NOTE 4Fir high STC rated products, two units in the size specified above might need to be tested in the filler wall in order to obtain soundtransmission coefficient differences that are greater than 6 dB at all f

31、requencies.E1425072double hinged door test specimen width shall not vary by morethan 50 mm (2 in.) and the height shall not vary by more than75 mm (3 in.).6. Test Methods6.1 The sequence of testing shall be: operating force (ifapplicable); followed by latching force (if applicable); fol-lowed by air

32、 leakage; and ending with sound transmission loss.If additional sash or panels are tested in the same specimenframe, the complete sequence of tests shall be repeated for eachset of sash or panels. The specimen shall be opened and closed(where applicable) at least five times prior to conducting theop

33、erating, latching force and air leakage tests.6.2 Operating forceThe operating force test shall beconducted on horizontal or vertical operating windows andsliding doors in accordance with ASTM E 2068. For dualwindows or doors, the operating force shall be measured onboth sets of sash or panels. The

34、operating force of rotaryoperators shall be determined in accordance with the proce-dures contained in the AAMA/WDMA/CSA 101/I.S.2/A440standard.6.2.1 The operating force shall not exceed the maximumforce to initiate motion and the maximum force to maintainmotion criteria contained in the AAMA/WDMA/C

35、SA 101/I.S.2/A440 standard. If adjustments need to be made, theoperating force shall be remeasured.6.3 Latching forceLatching force tests shall be conductedon swinging (side-hinged) doors with latches. The latchingforce test shall be conducted in accordance with procedurescontained in the AAMA/WDMA/

36、CSA 101/I.S.2/A440 stan-dard. For multiple doors, such as dual doors (back to back) ordouble doors (side by side) the latching force shall be con-ducted on all panels containing latching hardware.6.3.1 The latching force shall not exceed the maximumlatching force requirement in the AAMA/WDMA/CSA 101

37、/I.S.2/A440 standard. If adjustments need to be made, theoperating force and latching force must be remeasured.NOTE 4A swinging door is defined as closed when the latch is fullysecured in the strike plate and the door remains in the closed position.6.4 Air leakage testThe air leakage test shall be p

38、er-formed in accordance with Test Method E 283. The air leakagetest pressure for windows, doors, and skylights shall be asspecified in the AAMA/WDMA/CSA 101/I.S.2/A440 stan-dard. The air leakage test for glazed wall and sloped glazingsystems shall be initially conducted at a test pressure of 75 Pa(1

39、.57 psf) and then at a test pressure 300 Pa (6.24 psf).6.4.1 For windows, doors, and skylights, the air leakageshall be recorded as pass or fail in accordance with the criteriacontained in the AAMA/WDMA/CSA 101/I.S.2/A440 stan-dard. For glazed wall and sloped glazing systems, report the airleakage a

40、t both test pressures. If any adjustments need to bemade, the operating force, latching force and air leakagemeasurements (where applicable) shall be repeated.NOTE 5For glazed wall and sloped glazing systems, the air leakageshall not exceed 0.3 L/s m2(0.06 cfm/ft2) at both test pressures, which isan

41、 industry standard and recommended in AAMA 501.6.5 Sound transmission loss testThe sound transmissionloss shall be performed in accordance withASTM Test MethodE90. If any adjustments or modifications are performed, thewhole sequence of tests (operating force, latching force, airleakage and sound tra

42、nsmission loss) shall be repeated, whereapplicable.7. Classification7.1 Products shall be classified based on their Outdoor-Indoor Transmission Class (OITC) and/or Sound TransmissionClass (STC) ratings.7.2 The OITC rating shall be calculated in accordance withClassification E 1332 for exterior windo

43、w, door, skylight andglazed wall sections. The STC rating shall be calculated inaccordance with Classification E 413 for interior window, doorand glazed wall sections. For products used for both interiorand exterior applications, both the OITC and STC ratings shallbe reported.8. Report8.1 Report the

44、 following information (if applicable):8.1.1 Date of test and date of report.8.1.2 Identification of the specimen (manufacturer, dimen-sions, type, model, materials, weight, and any other pertinentinformation). It shall be noted if test specimen does not meetthe size requirements in 5.2 and Table 1.

45、8.1.3 Detailed drawings of the specimen showing dimen-sioned section profiles of the frame, sash or door panels, weepholes, weep covers, hardware, weather-stripping, seals, glazingdetails and any other pertinent construction details. Anymodifications made on the specimen to obtain the reportedvalues

46、 shall be noted on the drawings.8.1.4 Frame or sash fill material (fiberglass, foam, sand,mortar, etc.).8.1.5 Descriptions of locking and operating mechanisms, ifapplicable.8.1.6 Descriptions of glazed assemblies (glass thickness,glass type (annealed, tempered, laminated, insulated glass,etc.), inte

47、rlayer thickness and type (for laminated glass), spacersystem, air space (for insulated glass and dual windows), airspace media for insulated glass units (air, argon gas, kryptongas, etc.), insulating glass films, muntins, manufacturer,method of glazing, and any other pertinent information.8.1.7 Des

48、criptions of all weather-stripping and/or seals andthe location on the test specimen.8.1.8 The operating forces as measured and recorded inaccordance with 6.2.8.1.9 The latching forces as measured and recorded inaccordance with 6.3.8.1.10 The air leakage as measured and recorded in accor-dance with

49、6.4.8.1.11 The transmission loss data in one-third octave bands80-4000 Hz as measured in accordance with 6.5. The tempera-ture and relative humidity in both rooms at the time of test shallbe reported. The glass temperature shall be reported for testspecimens containing laminated glass.8.1.12 The classification of the specimen in accordance withSection 7.8.1.13 A statement that the test or tests were conducted inaccordance with this practice. Any deviations from this prac-tice shall be explicitly noted.E14250739. Keywords9.1 acoustics; air leakage; curtain w