ASTM D5897-2013 3750 Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric TitrationAlternative Method《用电位滴定交替法测定纤维素酯的羟百分率的标准试验方法》.pdf
《ASTM D5897-2013 3750 Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric TitrationAlternative Method《用电位滴定交替法测定纤维素酯的羟百分率的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D5897-2013 3750 Standard Test Method for Determination of Percent Hydroxyl on Cellulose Esters by Potentiometric TitrationAlternative Method《用电位滴定交替法测定纤维素酯的羟百分率的标准试验方法》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D5897 13Standard Test Method forDetermination of Percent Hydroxyl on Cellulose Esters byPotentiometric TitrationAlternative Method1This standard is issued under the fixed designation D5897; the number immediately following the designation indicates the year oforiginal adoption or, in th
2、e case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a procedure for determining thepercent hydroxyl on cellulose e
3、sters by potentiometric titration.The typical range of percent hydroxyl measured is 0.7 to10.0 %.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any
4、, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D817 Test Methods of Testing Cellulose Acetate Prop
5、ionateand Cellulose Acetate ButyrateD871 Test Methods of Testing Cellulose Acetate3. Summary of Test Method3.1 The cellulose ester is dissolved in pyridine and thehydroxyl sites on the cellulose ester are acetylated with aceticanhydride in the presence of basic catalyst, 1-methylimidazole.The excess
6、 acetic anhydride is hydrolyzed and the resultingacetic acid is titrated with sodium hydroxide. An automatictitrator dispenses the titrant, potentiometrically determines theendpoint, and calculates the percent hydroxyl on the celluloseester based on a blank determination.4. Significance and Use4.1 T
7、his test method provides a simpler means for thedetermination of the hydroxyl content of cellulose esters thanthe preparation and measurement of the carbanilate derivativedescribed in Test Methods D817 and D871.4.2 The hydroxyl content is an important indicator ofsolubility and reactivity.5. Interfe
8、rences5.1 Undissolved ester may accumulate on the sides of theflask and on top of the stirring-star during dissolution, leadingto low results. Gently swirling the solution during titration canreduce this problem.5.2 The ground glass joints of the flask and the air con-denser must always be rinsed in
9、to the flask with hydrolyzingsolution at the point of hydrolysis and before titration. This willprevent erroneous results from material that may have refluxedinto the joint.6. Apparatus6.1 Titrator, equipped with Glass Electrode.6.2 Heating/Stirring Module, six-place.6.3 Heating/Stirring Block, cut
10、from polished-finish alumi-num block to fit stirrer in 6.2 (see Fig. 1 for dimensions).6.4 Stirrer, six place.6.5 Magnetic Stirrers, size 25 mm and 50 mm.6.6 Stirring Bar.6.7 Flask and Air Condenser, (see Fig. 2 for dimensions).6.8 Bottle-Top Dispensers, capable of dispensing 20 mL, 35mL, and 50 mL,
11、 or equivalent.6.9 Analytical Balance, capable of weighing 250 g to thefourth decimal place.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.36 on Cellulose and Cellulose De
12、rivatives.Current edition approved June 1, 2013. Published June 2013. Originallyapproved in 1996. Last previous edition approved in 2007 as D5897 96 (2007).DOI: 10.1520/D5897-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.
13、For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.10 Analytical Balance, capable of weighing 1000 g to thesecond deci
14、mal place.7. Reagents and Materials7.1 Purity of ReagentsAmerican Chemical Society3re-agent grade chemicals shall be used throughout this test unlessotherwise indicated.7.2 Pyridine.7.3 Acetic Anhydride.7.4 Acetylating Solution115 6 0.50 g of acetic anhydrideper litre of pyridine. The container need
15、s to be equipped with20-mL buret. The shelf-life of this solution is 5 days.7.5 Dimethylformamide.7.6 Deionized Water, purified to 18.3 M resistance.7.7 Hydrolyzing SolutionMix 600 mLdimethylformamide, 300 mL pyridine, and 100 mL water in a1-L bottle equipped with a bottle top dispenser capable ofdo
16、sing 35 mL. Stir for at least 10 min prior to use. Theshelf-life of this solution is 1 month.7.8 1-Methylimidazole.7.9 Sucrose.7.10 Acetone.7.11 Potassium Acid Phthalate (KHP), National Institute ofStandards and Technology primary standard grade. Store indesiccator, after drying for1hat105C (65C).7.
17、12 Methanol.7.13 Sodium Hydroxide, 0.5 N in methanol. This solutionhas a shelf life of 2 weeks.7.14 Traceable Buffers, pH 4 and pH 7, available fromNational Institute of Standards and Technology.7.15 Potassium Chloride (KCl), 5 M, weigh 37.3 g(60.3000 g) of KCl into a 100-mL volumetric flask. Dilute
18、 tothe mark with purified water. Shake into solution.7.16 1,2-Dichloroethane.8. Calibration and Standardization8.1 Calibration of the Electrode:NOTE 1If the electrode is new, perforate the nipple on the rubber cap3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society,
19、 Washington, DC. For Suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.FIG.
20、 1 Heating/Stirring Block DimensionsFIG. 2 Flask and Air Condenser DimensionsD5897 132and soak the electrode in 5 M potassium chloride for 1 h. Store in pH 4buffer until use.8.1.1 Select from the titrator menu the procedure for cali-bration of the electrode.8.1.2 Add about 50 mL of pH 4 buffer into
21、a titration cupand lower the electrode into it.8.1.3 Run the procedure for the titrator to read the correctpH.8.1.4 Repeat process 8.1.1-8.1.3 for buffer pH 7.8.1.5 Make sure that the calibration is done when a newelectrode is put into use and then check once/month thereafteror when a problem is sus
22、pected.8.2 Standardization of Methanolic 0.5 N Sodium Hydroxide:8.2.1 Weigh approximately 1.5 6 0.1000 g of KHP into atitration cup and record the weight. Add about 35 mL ofpurified water and allow to dissolve.8.2.2 Ensure that the burette is flushed with the 0.5 NNaOH.8.2.3 Titrate the sample.8.2.4
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD589720133750STANDARDTESTMETHODFORDETERMINATIONOFPERCENTHYDROXYLONCELLULOSEESTERSBYPOTENTIOMETRICTITRATIONALTERNATIVEMETHOD

链接地址:http://www.mydoc123.com/p-520993.html