ASTM D4014-2003(2007) Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges《桥梁用普通和钢层压弹性体支承标准规范》.pdf

《ASTM D4014-2003(2007) Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges《桥梁用普通和钢层压弹性体支承标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4014-2003(2007) Standard Specification for Plain and Steel-Laminated Elastomeric Bearings for Bridges《桥梁用普通和钢层压弹性体支承标准规范》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 4014 03 (Reapproved 2007)Standard Specification forPlain and Steel-Laminated Elastomeric Bearings forBridges1This standard is issued under the fixed designation D 4014; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers bearings, which consist of allelastomer or of alternate laminates of elastomer

3、 and steel,when the function of the bearings is to transfer loads oraccommodate relative movement between a bridge superstruc-ture and its supporting structure, or both.1.2 The values stated in SI units are to be regarded as thestandard.NOTE 1The words “elastomer” or “elastomeric” will be used inter

4、-changeably with the word “rubber” in this specification.1.3 The following safety hazards caveat pertains only to thetest methods portion, Section B, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility o

5、f the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2A 36/A 36M Specification for Carbon Structural SteelD 395 Test Methods for Rubber PropertyCompressionSetD

6、412 Test Methods for Vulcanized Rubber and Thermo-plastic ElastomersTensionD 518 Test Method for Rubber DeteriorationSurfaceCrackingD 573 Test Method for RubberDeterioration in an AirOvenD 832 Practice for Rubber Conditioning For Low Tempera-ture TestingD 1149 Test Methods for Rubber DeteriorationCr

7、ackingin an Ozone Controlled EnvironmentD 1415 Test Method for Rubber PropertyInternationalHardnessD 1418 Practice for Rubber and Rubber LaticesNomenclatureD 2000 Classification System for Rubber Products in Auto-motive ApplicationsD 2137 Test Methods for Rubber PropertyBrittlenessPoint of Flexible

8、Polymers and Coated FabricsD 2240 Test Method for Rubber PropertyDurometerHardnessD 3183 Practice for RubberPreparation of Product Piecesfor Test Purposes from ProductsE4 Practices for Force Verification of Testing Machines3. Terminology3.1 Definitions:3.1.1 design loadthe mean compressive stress ap

9、plied tothe area of the steel laminate.3.1.2 external load platea steel plate bonded to the top orbottom elastomeric surface of a bearing, or both.3.1.3 lotunless otherwise specified in the contract orpurchase order, a lot shall consist of a single type of bearing, ofthe same design and material, su

10、bmitted for inspection at thesame time.3.1.4 plain elastomeric bearing pada bearing that con-sists only of elastomeric material.3.1.5 plain elastomeric sandwich bearinga bearing thatconsists of a single layer of elastomeric material bonded to oneor two external load plates (3.1.2).3.1.6 steel-lamina

11、ted elastomeric bearinga bearingmolded of elastomeric material with one or more steel lami-nates embedded in and bonded to it, and to which one or twoexternal load plates (3.1.2) may be bonded.4. Classification4.1 The bearings are furnished in four types as follows:4.1.1 Plain Elastomeric Bearing Pa

12、d.4.1.2 Plain Elastomeric Sandwich Bearing.4.1.3 Steel-Laminated Elastomeric Bearing.1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.32 onBridges and Structures.Current edition approved Dec. 1, 2007.

13、 Published January 2008. Originallyapproved in 1981. Last previous edition approved in 2003 as D 4014 03.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standar

14、ds Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Copyright by ASTM Intl (all rights reserved); Sun Sep 28 03:15:41 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement

15、. No further reproductions authorized.4.1.4 Steel-Laminated Elastomeric Bearing with ExternalLoad Plate(s).NOTE 2Examples of the types of elastomeric bearing construction aregiven in Fig. 1.NOTE 3The adjective elastomeric is omitted in this specificationwhen referring to bearing types.4.2 The elasto

16、mer for the manufacture of the bearing isfurnished in two types as follows:4.2.1 Type CRChloroprene rubber.4.2.2 Type NRNatural rubber.4.2.3 If none is specified then the manufacturer shall use oneof those types.NOTE 4Appendix X1 relates to elastomeric materials which do nothave fully documented in-

17、service records or sufficiently widespread use orboth.NOTE 5The abbreviations for the elastomer types are taken fromPractice D 1418.4.3 The elastomer for the manufacture of the bearing isfurnished in four grades of low-temperature properties. Thegrades and typical operating temperature conditions fo

18、r eachgrade are as follows:4.3.1 Grade 0Suitable for continuous use down to +5C.4.3.2 Grade 2Sub-zero temperatures occur at night andoccasionally persist for no more than one or two days.4.3.3 Grade 3Same as Grade 2 but occasional periods ofup to two weeks continuously below zero.4.3.4 Grade 5Sub-ze

19、ro temperatures down to 40C per-sisting for several months each year with up to two monthscontinuously below 15C.4.3.5 If a grade is not specified Grade 0 shall be furnished.An elastomer of a higher grade number may be substituted forany lower grade.NOTE 6A discussion of low-temperature properties o

20、f elastomericmaterials is given in Practice D 832.FIG. 1 Examples of the Construction of Elastomeric BearingsD 4014 03 (2007)2Copyright by ASTM Intl (all rights reserved); Sun Sep 28 03:15:41 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions author

21、ized.NOTE 7The grade numbers for the low-temperature properties corre-spond to those in Table 6 of Classification D 2000.5. Ordering Information5.1 Orders for each type of bearing under this specificationshall include the following:5.1.1 Quantity,5.1.2 Bearing design,NOTE 8An example of the design i

22、nformation required is given inAppendix X2. Working drawings may be substituted.5.1.3 Design load,5.1.4 Shear modulus of the elastomer,5.1.5 Rubber type,5.1.6 Rubber grade,5.1.7 Ozone test partial pressure, if higher than 50 mPa(formerly referred to as a concentration of 50 parts per hundredmillion

23、(pphm).6. Materials and Manufacture6.1 The elastomeric compound used in the construction of abearing shall contain only either natural rubber or chloroprenerubber as the raw polymer. No reclaimed rubber shall be used.6.2 Internal steel laminates shall be of rolled mild steel.6.3 External load plates

24、 shall conform to the requirementsof Specification A 36/A 36M unless otherwise specified in thecontract or purchase order.6.4 Plain bearing pads shall be molded individually, or cutfrom previously molded strips or slabs, or extruded and cut tolength. Cutting shall produce a smooth surface and no hea

25、tingof the elastomer.6.5 A steel-laminated bearing or a plain sandwich bearingshall be molded as a single unit under pressure and heat.6.6 All bonding of elastomer to steel laminates and toexternal load plates shall be carried out during molding. Theelastomer at the outer edges of bonds to external

26、load platesshall be shaped to avoid serious stress concentrations (see Fig.1).6.7 Internal steel laminates shall be free of sharp edges.6.8 External load plates shall be protected from rustingwhen supplied by the manufacturer.6.9 All molds shall have a standard shop-practice moldfinish.7. Dimensions

27、 and Permissible Variations7.1 All elastomeric layers, for example, plain-bearing pads,laminates, and covers, shall be of uniform thickness unlessotherwise specified in the contract or purchase order.7.2 All internal steel laminates shall be of uniform thick-ness. When specified in the contract or p

28、urchase order, thethickness of the outer steel laminates may differ if not adjacentto an external load plate (see Fig. 1).7.3 The minimum thickness of internal steel laminates shallbe 1.5 mm or 0.060 in. (16 gage) when the greater of the lengthor width of a rectangular bearing or the diameter of a c

29、ircularbearing is less than 450 mm or 18 in. In all other cases, theminimum thickness shall be 2 mm or 0.075 in. (14 gage).7.4 External load plates shall be of uniform thickness unlessotherwise specified in the contract or purchase order.7.5 Bearing dimensions and elastomer layer thicknessesshall sa

30、tisfy the tolerances in Table 1, in which D is the length,width or diameter as appropriate, and T is the total elastomerthickness.7.6 Variation from a plane parallel to a design surface shallnot exceed an average slope of 0.005 for the upper surface and0.006 for a side surface.8. Test Methods and Ac

31、ceptance Requirements8.1 Bearing Compression TestsAll bearings sampled froma lot shall be subjected to the compression tests. The cost ofreplacement bearings and of testing them shall be borne by thesupplier.8.1.1 The bearings shall be brought to a temperature of 23 66C and shall be tested at this t

32、emperature.8.1.2 Compression StiffnessLoad the bearing to the designload (3.1.1) by increments of one fifth of the design load. Foreach load increment, the loading time shall be within the rangeof 1.4 to 2.6 min. When the increment has been applied theload or deflection (depending on the type of tes

33、ting machine)shall be maintained constant for 30 s then the load anddeflection measured. From a plot of load against deflection, thecompression stiffness shall be determined as the slope of thebest straight line through the points, ignoring the first point atzero load. Record the compressive stiffne

34、ss for each bearing.8.1.3 Visual InspectionIncrease the load to 1.5 times thedesign load then maintain either load or deflection constantwhile the bearing is inspected for visual faults, as follows:8.1.3.1 If lack of elastomer to steel bond is indicated, thebearing shall be rejected.8.1.3.2 If lamin

35、ate placement faults are observed whichresult in elastomer layer thickness that exceed the tolerances in7.5, the bearing shall be rejected.8.1.3.3 If there are at least three separate surface crackswhich are each at least 2 mm wide and 2 mm deep, the bearingshall be rejected.8.1.4 Record the median

36、compressive stiffness (K)ofthebearing of median stiffness. The compressive stiffness of eachbearing tested shall not differ from (K) by more than 10 %.8.1.5 For each bearing that fails to meet the requirements in8.1, two additional bearings may be sampled and shall meet allthe requirements in 8.1 or

37、 the lot shall be rejected.8.1.6 If the lot is not rejected, the bearing of medianstiffness (K) shall be subjected to the elastomeric material testsin 8.2.TABLE 1 Tolerances for Bearing Dimensions and ElastomerLayer ThicknessesDimensionToleranceMinimum MaximumLength, width or diameter ofbearing, mm

38、(in.)0 5 (0.2) + 0.005DHeight of bearing, mm (in.) 0 2 (0.1) + 0.04TThickness of elastomercoverat top, bottom or side,mm (in.)0 3 (0.1)Thickness of internal elas-tomer laminate, %620 % of designvalueD 4014 03 (2007)3Copyright by ASTM Intl (all rights reserved); Sun Sep 28 03:15:41 EDT 2008Downloaded

39、/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions authorized.8.2 Elastomeric Material Tests:8.2.1 All test specimens used for the determination of theproperties of the vulcanized elastomeric material shall be takenfrom bearings (see Practice D 3183). Tensile and har

40、dnessspecimens for the quality control tests in 8.2.3, specimens forthe ozone resistance test in 8.2.5, and strips for the low-temperature brittleness test in 8.2.6.1, if applicable, shallinclude an outer surface of a bearing.All other specimens shallbe taken from within the middle one third of a be

41、aring.Compression set specimens shall be as specified in TestMethods D 395, Method B, Type 1.8.2.2 The temperature at which the tests shall be carried outshall be 23 6 2C except where otherwise specified in thisspecification.8.2.3 Quality Control PropertiesThe quality control prop-erties of the elas

42、tomer shall meet the requirements of Table 2for the hardness and type of rubber used.8.2.4 Shear ModulusThe shear modulus of the elastomerdetermined in accordance with Annex A1 shall not differ bymore than 615 % from the required shear modulus of theelastomer.8.2.5 Ozone ResistanceAn ozone resistanc

43、e test shall becarried out on test strips mounted in accordance with procedureA of Test Method D 518. The test shall be carried out inaccordance with Test Methods D 1149 at 20 % strain and at 406 2C for 100 h. The ozone test partial pressure shall be 50 65 mPa formerly referred to as a concentration

44、 of 50 6 5 pphmunless a higher test partial pressure has been specified. The teststrips shall be examined for cracks using a 73 magnificationlens. The elastomer has adequate ozone resistance if noperpendicular cracks are observed on that surface of the stripcorresponding to the outer surface of the

45、bearing.8.2.6 Low-Temperature Grade Tests:8.2.6.1 When Low-Temperature Grade 2, 3, or 5 is speci-fied, a low-temperature brittleness test shall be carried out inaccordance with Test Methods D 2137, Method A using fivetest strips. The temperature at which the strips shall beconditioned and tested sha

46、ll be 10C for Grade 2, 25C forGrade 3, and 40C for Grade 5. To meet the requirements ofthis specification, none shall fail.9. Sampling9.1 Unless otherwise specified in the contract or purchaseorder, sampling shall consist of the following.9.1.1 For acceptance purposes, bearing from within the lotsha

47、ll be selected at random as samples for inspection andtesting.9.1.2 A minimum of three bearings shall be taken from thelot for testing. If the number of bearings in the lot exceeds 50then for each 50, or part thereof, one additional bearing shall betaken for testing.10. Product Marking10.1 Every bea

48、ring shall be marked in indelible ink orflexible paint. The marking shall consist of the order number,lot number, bearing identification number and elastomer typeand grade reference number.10.2 Unless otherwise specified in the contract or purchaseorder, the marking should be on a side face visible

49、aftererection of the bridge.11. Precision and Bias11.1 No user is currently interested in participating in around robin test to verify precision and bias. As an alternative,two producers have agreed to run repeatability in their ownlaboratories.TABLE 2 Quality Control Properties of ElastomerRubber NR CRHardness limits (TestMethod D 1415 or TestMethod D 2240)45 to 75 45 to 75Physical properties(Test Methods D 412):Tensile strength,min, MPa (psi)15.5 (2250) 15.5 (2250)Ultimate elongation:45 to 55hardness, min, %400 40056 to 65hard