ASTM D3239-1991(2011) Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry《高电离电压质谱法气油芳烃馏分芳烃类型分析的标准试验方法》.pdf

《ASTM D3239-1991(2011) Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry《高电离电压质谱法气油芳烃馏分芳烃类型分析的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3239-1991(2011) Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry《高电离电压质谱法气油芳烃馏分芳烃类型分析的标准试验方法》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3239 91 (Reapproved 2011)Standard Test Method forAromatic Types Analysis of Gas-Oil Aromatic Fractions byHigh Ionizing Voltage Mass Spectrometry1This standard is issued under the fixed designation D3239; the number immediately following the designation indicates the year oforiginal ado

2、ption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method2covers the determination by highionizing voltage, low

3、resolution mass spectrometry of 18aromatic hydrocarbon types and 3 aromatic thiophenotypes instraight run aromatic petroleum fractions boiling within therange from 205 to 540C (400 to 1000F) (corrected toatmospheric pressure). Samples must be nonolefinic, mustcontain not more than 1 mass % of total

4、sulfur, and mustcontain not more than 5 % nonaromatic hydrocarbons. Com-position data are in volume percent.NOTE 1Although names are given to 15 of the compound typesdetermined, the presence of other compound types of the same empiricalformulae is not excluded. All other compound types in the sample

5、,unidentified by name or empirical formula, are lumped into six groups inaccordance with their respective homologous series.1.2 The values stated in acceptable SI units are to beregarded as the standard. The values given in parentheses areprovided for information purposes only.1.3 This standard does

6、 not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stand

7、ards:3D2549 Test Method for Separation of Representative Aro-matics and Nonaromatics Fractions of High-Boiling Oilsby Elution ChromatographyD2786 Test Method for Hydrocarbon Types Analysis ofGas-Oil Saturates Fractions by High Ionizing VoltageMass SpectrometryE137 Practice for Evaluation of Mass Spe

8、ctrometers forQuantitative Analysis from a Batch Inlet43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Characteristic Mass Summations Classes IVII:3.1.2 Class I:(78 5 78 1 92 1 106 1 120 1 to end, polyisotopic1 91 1 105 1 119 1 to end, monoisotopic (1)3.1.3 Class II:(104 5 104

9、 1 118 1 132 1 146 1 to end, polyisotopic1 117 1 131 1 145 1 to end, monoisotopic (2)3.1.4 Class III:(129 5 130 1 144 1 158 1 172 1 to end, polyisotopic1 129 1 143 1 157 1 171 1 to end, monoisotopic (3)3.1.5 Class IV:(128 5 128 1 142 1 156 1 170 1 to end, polyisotopic1 141 1 155 1 169 1 to end, mono

10、isotopic (4)3.1.6 Class V:(154 5 154 1 168 1 182 1 196 1 to end, polyisotopic1 167 1 181 1 195 1 to end, monoisotopic (5)3.1.7 Class VI:(166 5 166 1 180 1 194 1 208 1 to end, polyisotopic1 179 1 193 1 207 1 to end, monoisotopic (6)3.1.8 Class VII:(178 5 178 1 192 1 206 1 220 1 to end, polyisotopic1

11、191 1 205 1 219 1 to end, monoisotopic (7)3.1.9 Classes, Compound Types, Empirical FormulaeSeeTable 1.4. Summary of Test Method4.1 The relative abundance of seven classes (IVII) ofaromatics in petroleum aromatic fractions is determined bymass spectrometry using a summation of peaks most charac-teris

12、tic of each class. Calculations are carried out by the use ofa 7 by 7 inverted matrix derived from published spectra of purearomatic compounds. Each summation of peaks includes the1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct

13、responsibility of SubcommitteeD02.04.0M on Mass Spectroscopy.Current edition approved Oct. 1, 2011. Published October 2011. Originallyapproved in 1973. Last previous edition approved in 2006 as D3239 91 (2006).DOI: 10.1520/D3239-91R11.2Robinson, C. J., and Cook, G. L., Analytical Chemistry (ANCHA),

14、Vol 41,1969, p. 1548.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Withdrawn. The last approved version of

15、 this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.polyisotopic homologous series that contains molecular ionsand the monoisotopic homologous series one mass unit lessthan the molec

16、ular ion series. Using characteristic summationsfound in the monoisotopic molecular ion1 series of peaks,each class is further resolved to provide relative abundances ofthree compound types: nominal (Type 0), first overlap (Type1), and second overlap (Type 2). The aromatic fraction isobtained by liq

17、uid elution chromatography (see Test MethodD2549).NOTE 2Monoisotopic peaks heights are obtained by correcting thepolyisotopic heights for naturally occurring heavy isotopes, assuming thatonly ions of CnH2n+2to CnH211are present. This is not strictly accuratefor aromatics, but the errors introduced b

18、y such assumption are trivial.5. Significance and Use5.1 Aknowledge of the hydrocarbon composition of processstreams and petroleum products boiling within the range 205 to540C (400 to 1000F) is useful in following the effect ofchanges in process variables, diagnosing the source of plantupsets, and i

19、n evaluating the effect of changes in compositionon product performance properties. This method, when usedtogether with Test Method D2786, provides a detailed analysisof the hydrocarbon composition of such materials.6. Apparatus6.1 Mass SpectrometerThe suitability of the mass spec-trometer to be use

20、d with this method shall be proven byperformance tests described both herein and in Practice E137.6.2 Sample Inlet SystemAny inlet system may be usedthat permits the introduction of the sample without loss,contamination, or change in composition. The system mustfunction in the range from 125 to 350C

21、 to provide anappropriate sampling device.6.3 Microburet or Constant-Volume Pipet.6.4 Mass Spectrum DigitizerIt is recommended that amass spectrum digitizer be used in obtaining the analysis,because it is necessary to use the heights of most of the peaksin the spectrum. Any digitizing system capable

22、 of supplyingaccurate mass numbers and peak heights is suitable.6.5 Electronic Digital ComputerThe computations forthis analysis are not practical without the use of a computer.Any computer capable of providing approximately 60 K bytesin core and capable of compiling programs written in FOR-TRAN IV

23、should be suitable.7. Reagent7.1 n-Hexadecane.(WarningCombustible-Very harm-ful.)8. Calibration8.1 Calibration equations in the computer program given inTable 2 may be used directly provided the following proce-dures are followed:8.1.1 Instrumental ConditionsRepeller settings are ad-justed to maximi

24、ze the m/e 226 ion of n-hexadecane. Amagnetic field is used that will permit a scan over the massrange from 78 to 700. An ionizing voltage of 70 eV and anionizing current in the range from 10 to 70 A is used.NOTE 3The instrument conditions and calibration equations de-scribed in this method are base

25、d on the use of a 180 magnetic-deflectiontype mass spectrometer (CEC Model 21-103). Satisfactory results havebeen obtained with some other magnetic deflection instruments. It is notknown if the equations are suitable for use on all other mass spectrometertypes.8.1.2 Computer ProgramThe FORTRAN progr

26、am givenin Table 2 contains all the equations for calculating theanalysis, including those for calculating monoisotopic peakheights. The program is compiled and linked to create acomputer load module that is available whenever needed.When the spectrum shown in Table 3 is processed, thee resultsshoul

27、d agree with those shown in Table 4.8.1.2.1 Data Input FormatThe input format suggested inthe main program may be changed to suit the needs ofindividual laboratories provided that true masses and peakheights are stored in the H(M) array.8.1.2.2 FORTRAN IV LanguageChanges in the programmay be require

28、d for compatibility with the particular comput-ing system to be used. These are permitted provided that thealtered program gives the results shown in Table 4 with theinput data of Table 3.NOTE 4The program, as shown in Table 2, has run satisfactorily onIBM System 360 computers.9. Procedure9.1 If the

29、 mass spectrometer has been in continuous opera-tion, no additional preparation is necessary before analyzingsamples. However, if the spectrometer has been turned on onlyrecently, check its operation according to the manufacturersinstructions to ensure stability before proceeding.9.2 Obtain the mass

30、 spectrum of the sample, scanning frommass 76 to the high-mass end of the spectrum.TABLE 1 Classes, Compound Types, and Empirical FormulaeClass Type FormulaI 0 alkylbenzenes, CnH2n-6I 1 benzothiophenes, CnH2n-10SI 2 naphthenephenanthrenes,CnH2n-20II 0 naphthenebenzenes, CnH2n-8II 1 pyrenes, CnH2n-22

31、II 2 unidentifiedIII 0 dinaphthenebenzenes, CnH2n-10III 1 chrysenes, CnH2n-24III 2 unidentifiedIV 0 naphthalenes, CnH2n-12IV 1 dibenzothiophenes, CnH2n-16SIV 2 unidentifiedV 0 acenaphthenes + dibenzofurans,CnH2n-14and CnH2n-16OVV12perylenes, CnH2n-28unidentifiedVI 0 fluorenes, CnH2n-16VI 1 dibenzant

32、hracenes, CnH2n-30VI 2 unidentifiedVII 0 phenanthrenes, CnH2n-18VII 1 naphthobenzothiophenes, CnH2n-22SVII 2 unidentifiedD3239 91 (2011)2TABLE 2 High Ionizing Voltage, Low Resolution Mass Spectrometric Analysis of Gas Oil Aromatic Fractions* The “end statement” designated is specific for IBM compute

33、rs. The user may modify the FORTRAN program to suit his individual needs.D3239 91 (2011)3TABLE 2 ContinuedD3239 91 (2011)4TABLE 2 ContinuedD3239 91 (2011)5TABLE 2 ContinuedD3239 91 (2011)6TABLE 2 ContinuedD3239 91 (2011)7TABLE 2 ContinuedD3239 91 (2011)8TABLE 2 ContinuedD3239 91 (2011)9TABLE 2 Conti

34、nuedD3239 91 (2011)1010. Calculations10.1 Recording Mass SpectrumRead peak heights and thecorresponding masses for all peaks in the spectrum of thesample. Use the data, along with sample identification, as inputto the computer.11. Precision and Bias11.1 The precision of this test method as obtained

35、bystatistical examination of interlaboratory test results on asample having the composition given in Table 5, is as follows:11.1.1 RepeatabilityThe difference between successivetest results obtained by the same operator with the sameapparatus under constant operating conditions on identical testmate

36、rial, would in the long run, in the normal and correctoperation of the test method, exceed the values shown in Table5 only in one case in twenty.11.1.2 ReproducibilityThe difference between two singleand independent results, obtained by different operators work-ing in different laboratories on ident

37、ical test material, would inthe long run, in the normal and correct operation of the testmethod, exceed the values shown in Table 5 only in one casein twenty.NOTE 5If samples are analyzed that differ appreciably in compositionfrom the sample used for the interlaboratory study, this precision state-m

38、ent may not apply.11.2 BiasThe quantities determined are defined by theconditions employed in this empirical method, and a statementof bias is therefore not appropriate.12. Keywords12.1 aromatic; gas oil; mass spectrometry; petroleumD3239 91 (2011)11TABLE 3 PC-69-378 Test Spectrum for Gas Oil Aromat

39、ics AnalysisD3239 91 (2011)12TABLE 4 Mass Spectral Analysis of Aromatic FractionsPC-69-378 Test Spectrum for Gas Oil Aromatics AnalysisCalc. Ion Sums Volume %Monoaromatics:AlkylbenzenesNaphthenebenzenesDinaphthenebenzenes9703.9017.9778.28498.13.312.313.438.9Diaromatics:NaphthalenesAcenaphthenes,dibe

40、nzofuransFluorenes4774.6576.7809.19158.6.59.010.726.2Triaromatics:PhenanthrenesNaphthenephenanthrenes6156.3470.9625.8.44.713.1Tetraaromatics:Pyrenes 3980.6070.5.48.390. Chrysenes 2090. 2.9Pentaaromatics:PerylenesDibenzanthracenes1293.366.1658.1.80.52.3Thiopheno Aromatics:BenzothiophenesDibenzothioph

41、enesNaphthobenzothiophenes565.968.339.1872.0.81.30.52.6Unidentified Aromatics: 6322. 8.6Class I incl withNaphthenephenanthrenesClass II 614. 0.8Class III 838. 1.1Class IV 3431. 4.7Class V 546. 0.7Class VI 281. 0.4Class VII 612. 0.8TABLE 5 Precision Summary Based on Cooperative DataVol % srsRr RAlkyl

42、benzenes 13.7 0.3 1.0 1.2 3.0Naphthenebenzenes 13.3 0.1 1.1 0.5 3.3Dinaphthenebenzenes 13.7 0.2 0.4 0.9 1.1Naphthalenes 6.7 0.2 0.8 0.9 2.3Acenaphthenes/dibenzofurans 9.0 0.1 0.2 0.5 0.5Fluorens 10.7 0.1 0.2 0.3 0.6PhenanthrenesNaphthenephenanthrenes8.64.50.10.20.30.40.20.71.01.2PyrenesChrysenes5.72

43、.80.10.20.50.40.30.51.61.1PerylenesDibenzanthracenes1.70.40.10.10.20.10.30.20.60.4Benzothiophenes 1.0 0.2 0.4 0.8 1.1Dibenzothiophenes 1.5 0.1 0.3 0.3 0.8Naphthabenzothiophenes 0.5 0.1 0.3 0.3 1.0Class II Unidentified 0.4 0.1 0.4 0.3 1.1Class III Unidentified 0.6 0.1 0.4 0.4 1.2Class IV Unidentified

44、 4.1 0.2 0.5 0.6 1.6Class V Unidentified 0.5 0.1 0.3 0.5 0.8Class VI Unidentified 0.2 0.1 0.1 0.3 0.4Class VII Unidentified 0.4 0.2 0.2 0.5 0.7sr= repeatability standard deviationsR= reproducibility standard deviationr = repeatabilityR = reproducibilityD3239 91 (2011)13ASTM International takes no po

45、sition respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibi

46、lity.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to A

47、STM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the addres

48、s shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3239 91 (2011)14