ASTM D2911 D2911M-2016 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶尺寸和公差的标准规格》.pdf

《ASTM D2911 D2911M-2016 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶尺寸和公差的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2911 D2911M-2016 Standard Specification for Dimensions and Tolerances for Plastic Bottles《塑料瓶尺寸和公差的标准规格》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2911 10D2911/D2911M 16Standard Specification forDimensions and Tolerances for Plastic Bottles1This standard is issued under the fixed designation D2911;D2911/D2911M; the number immediately following the designation indicatesthe year of original adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification covers the thread configuration and dimensions for finishes for plastic bottles wit

3、h screw-type closures,having a maximum capacity of 18.9 L (5 gal) and a maximum bottle dimension of 305 mm (12 in.). Included are tolerances forbottle capacity and body dimensions.1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded as the separately as standard. The

4、valuesstated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combiningvalues from the two systems may result in non-conformance with the standard.1.3 The following precautionary caveat pertains only to the test methods portion, Section 8

5、of this specification.This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use

6、.NOTE 1There is no known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1898 Practice for Sampling of Plastics (Withdrawn 1998)33. Terminology3.1 Definitions:3.1.1 bottle finishthe configuration of the neck or opening of

7、 the bottle which serves to engage specific parts of the closurein order to securely attach it to the bottle.3.1.2 bottle heightthe maximum dimension of a bottle in a plane perpendicular to the bottle base when the bottle is settingin its normal upright position.3.1.3 bottle thicknessthe smaller dim

8、ension in a plane parallel to the bottle base.3.1.4 bottle widththe larger dimension in a plane parallel to the bottle base.4. Dimensions and Recommended Variations4.1 Recommended Variations in Overflow CapacityIn overflow capacity recommended variations of plastic bottles up to 18.9L (5 gal) in siz

9、e shall be in accordance with Table 1.4.2 Recommended Variations in Body DimensionsThe recommended variations in the body dimensions of plastic bottlescovered by this specification shall be in accordance with Table 2.4.3 Finish Dimensions and DesignThe bottle finish dimensions and design for the nin

10、e finishes covered by this specificationshall be in accordance with Figs. 1-8 and Tables 3-10.1 This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.19 on Film, Sheeting, and MoldedProducts.Current edition approved July 1

11、, 2010April 1, 2016. Published September 2010April 2016. Originally approved in 1970. Last previous edition approved in 20052010 asD2911 - 94 (2005).D2911 - 10. DOI: 10.1520/D2911-10.10.1520/D2911-16.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service

12、 at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the u

13、ser of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard

14、as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Sampling5.1 A batch or lot shall be considered as a uni

15、t of manufacture.5.2 Unless otherwise agreed upon between manufacturer and purchaser, the material shall be sampled in accordance with theprocedure described in Section 9 of Practice D1898. Adequate statistical sampling prior to packaging shall be considered anacceptable alternative.6. Conditioning6

16、.1 ConditioningCondition the test specimens at 23 6 2C (73.4 6 3.6F) and 50 6 5% relative humidity for not less than40 h prior to test in accordance with Procedure A of Practice D618 for those tests where conditioning is required. In cases ofdisagreement, the , unless otherwise specified by contract

17、 or the relevant ASTM material specification. Conditioning time isspecified as a minimum. Temperature and humidity tolerances shall be 6 1C (61.8F) and 62 % relative humidity.in accordancewith Section 7 of Practice D618, unless specified differently by contract or material specification.6.2 Test Con

18、ditionsConduct the tests in the standard laboratory atmosphere of 23 6 2C (73.4 6 3.6F) and 50 6 5 % relativehumidity,at the same temperature and humidity used for conditioning with tolerances in accordance with Section 7 of PracticeD618, unless otherwise specified in the test methods or in this spe

19、cification. In cases of disagreement, the tolerances shall be 61C(61.8F) and 62 % relative humidity. by contract or the relevant ASTM material specification.7. Apparatus7.1 For Determining Bottle Capacity:7.1.1 Balance, having an accuracy of 60.1 % or better at rated capacity (full scale).7.1.2 Pipe

20、t, Graduated Cylinder, and Beaker, as required.7.1.3 Conditioned water at 23 6 2.0C (73.46 3.6F) containing a wetting agent sufficient to flatten the meniscus and eliminateair bubbles.TABLE 1 Bottle Overflow Capacity Tolerances for Plastic BottlesFluid Ounces MillilitresBottle Overflow Capacity Tole

21、rance () Bottle Overflow Capacity Tolerance ()less than 0.75 0.05 less than 22 1.50.75 and less than 1.2 0.07 22 and less than 35 2.01.2 and less than 1.6 0.08 35 and less than 47 2.51.6 and less than 2.1 0.10 47 and less than 62 3.02.1 and less than 2.8 0.12 62 and less than 83 3.52.8 and less than

22、 3.9 0.14 83 and less than 115 43.9 and less than 5.4 0.17 115 and less than 159 55.4 and less than 7.4 0.20 159 and less than 218 67.4 and less than 9.8 0.24 218 and less than 289 79.8 and less than 13 0.30 289 and less than 384 913 and less than 18 0.37 384 and less than 531 1118 and less than 26

23、0.44 531 and less than 767 1326 and less than 37 0.51 767 and less than 1092 1537 and less than 51 0.68 1092 and less than 1505 2051 and less than 72 0.81 1505 and less than 2125 2472 and less than 98 1.01 2125 and less than 2892 3098 and less than 119 1.30 2892 and less than 3512 38119 and less tha

24、n 139 1.50 3512 and less than 4103 44139 and less than 160 1.80 4103 and less than 4723 53160 and less than 180 2.00 4723 and less than 5313 59180 and less than 210 2.20 5313 and less than 6199 65210 to 5 gallons 1 % of capacity 6199 to 18.89 litres 1 % of capacityTABLE 2 Body Dimensional ToleranceR

25、ange of Specific Dimensions Height Dimensions Width and Depth Dimensionsin. mm in. mm in. mm0 up to but not including 1 0 to 25.40 0.030 0.76 0.030 0.761 up to but not including 2 25.40 to 50.80 0.030 0.76 0.050 1.272 up to but not including 4 50.80 to 101.60 0.050 1.27 0.060 1.524 up to but not inc

26、luding 6 101.60 to 152.40 0.050 1.27 0.080 2.036 up to but not including 8 152.40 to 203.20 0.060 1.52 0.090 2.298 up to but not including 10 203.20 to 254.00 0.060 1.52 0.110 2.7910 up to but not including 12 254.00 to 304.80 0.080 2.03 0.120 3.0512 up to but not including 15 304.80 to 381.00 0.090

27、 2.29 0.150 3.8115 up to but not including 18 381.00 to 457.20 0.110 2.79 0.150 3.81D2911/D2911M 162“L” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. a b c Threads/in. a b c5 in. 0.120 0.060 0.051 5 in. 0.120 0.060 0.049mm 3.05 1.52

28、 1.30 mm 3.05 1.52 1.246 in. 0.094 0.047 0.040 6 in. 0.094 0.047 0.039mm 2.39 1.19 1.02 mm 2.39 1.19 0.998 in. 0.084 0.042 0.036 8 in. 0.084 0.042 0.035mm 2.13 1.07 0.91 mm 2.13 1.07 0.89Example Thread Nomenclature“L” Style: L28SP400“M” Style: M28SP400NOTE 1T and E dimensions are the average of two

29、measurements across the major and minor axis. The limits of ovality will be determined by thecontainer supplier and container customer, as necessary.NOTE 2Dimension H is measured from the top of the finish to the point where diameter T, extended parallel to the centerline, intersects the beador shou

30、lder.NOTE 3Contour of bead, undercut or shoulder is optional.NOTE 4Unless otherwise specified, I min applies to the full length of the opening.NOTE 5Concentricity of I min with respect to diameters T and E is not included. I min is specified for filler tube only.NOTE 6A minimum of 1 full turn of thr

31、ead shall be maintained.NOTE 7Corresponding dimensions and finish details are shown in Table 3.NOTE 8Consideration must be given to the sealing surface width for the sealing system being used.NOTE 9Many child resistant closures, etc.FIG. 1 SP 400 Finish Thread Cross SectionsD2911/D2911M 163NOTE 2It

32、is acceptable to use any liquid detergent as the wetting agent.7.1.4 Stop Watch. Watch or Comparable Timing Device.7.2 For Determining Finish and Body Dimensions:7.2.1 Micrometers, Vernier Height Gages, or Vernier CalipersVernier Calipers, or Comparable Instruments with an accuracyof 60.025 mm (60.0

33、01 in.).7.2.2 Internal Micrometers or Telescoping Gages with an accuracy of 60.025 mm (60.001 in.).7.2.3 Commercial Scale, good quality calibrated in 1-mm or 132-in. increments.“L” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. a b c

34、 Threads/in. a b c6 in. 0.094 0.047 0.040 6 in. 0.094 0.047 0.039mm 2.39 1.19 1.02 mm 2.39 1.19 0.998 in. 0.084 0.042 0.036 8 in. 0.084 0.042 0.035mm 2.13 1.07 0.91 mm 2.13 1.07 0.89Example Thread Nomenclature:“L” Style: L22SP410“M” Style: M22SP410NOTE 1Construction of neck from B to D must be held

35、within the shaded area shown.NOTE 2A minimum of 112 turns of thread shall be maintained.NOTE 3Unless otherwise specified, I min applies to the full length of the opening.NOTE 4Concentricity of I min with respect to diameters T and E is not included. I min is specified for filler tube only.NOTE 5T an

36、d E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by thecontainer supplier and container customer, as necessary.NOTE 6Consideration must be given to the sealing surface width for the sealing system being used.NOTE 7When valve

37、 style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition,it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for finishing the inside diameter.NOTE 8Corresponding dimensions and de

38、tails shown in Table 4.FIG. 2 SP 410 Finish Thread Cross SectionsD2911/D2911M 1648. Test Methods8.1 Bottle Capacity:8.1.1 Weigh the empty bottle and record the weight in grams.8.1.2 Fill the bottle to overflow capacity with conditioned water containing the wetting agent, adjusting the meniscus by us

39、e ofa pipet, if necessary, until the meniscus is tangent to the top of the finish surface. No more than 2 min shall be allowed for fillingthe bottle and no additional water shall be added after the bottle is filled to overflow and free of air bubbles.8.1.3 If the time exceeds 2 min, discard the samp

40、le and start over.“L” Style “M” StyleAll-Purpose Thread(Plastic or Metal Closures)Modified Buttress Thread(Plastic Closures)Threads/in. a b c d f Threads/in. a b c d f6 in. 0.094 0.047 0.040 0.020 0.020 6 in. 0.094 0.047 0.039 0.030 0.030mm 2.39 1.19 1.02 0.51 0.51 mm 2.39 1.19 0.99 0.76 0.768 in. 0

41、.084 0.042 0.036 0.020 0.020 8 in. 0.084 0.042 0.035 0.030 0.030mm 2.13 1.07 0.91 0.51 0.51 mm 2.13 1.07 0.89 0.76 0.7612 in. 0.045 0.030 0.011 0.015 0.005 12 in. 0.051 0.030 0.016 0.020 0.008mm 1.14 0.76 0.28 0.38 0.13 mm 1.29 0.76 0.41 0.51 0.22Example Thread Nomenclature:“L” Style: L22SP415“M” St

42、yle: M22SP415NOTE 1Construction of neck from B to D must be held within the shaded area shown.NOTE 2A minimum of 2 turns of thread shall be maintained.NOTE 3Unless otherwise specified, I min applies to the full length of the opening.NOTE 4Concentricity of I min with respect to diameters T and E is n

43、ot included. I min is specified for filler tube only.NOTE 5T and E dimensions are the average of two measurements across the major and minor axis. The limits of ovality will be determined by thecontainer supplier and container customer, as necessary.NOTE 6Consideration must be given to the sealing s

44、urface width for the sealing system being used.NOTE 7When valve style closures are used with this finish, special consideration must be given to a specific controlled inside diameter. In addition,it is acceptable to vary the dimensions indicated with asterisk (*) to ensure adequate material for fini

45、shing the inside diameter.NOTE 8Corresponding dimensions and finish details are shown in Table 5.FIG. 3 SP 415 Finish Thread Cross SectionsD2911/D2911M 165NOTE 3The capacity of the container is somewhat time-dependent in that the force of the water in the container will cause the container sides to

46、bulgewith time and additional water will be needed to adjust to overflow capacity.8.1.4 Weigh the filled bottle and record the weight in grams.8.1.5 Calculate the bottle volume as follows:Bv mL!5Bf 2Be!/0.997where:Bv = volume of bottle, mL,Bf = weight of filled bottle, g,Be = weight of empty bottle,

47、 g, and0.997 = weight of water (g/mL) at 23 6 2.0C (73.4 6 3.6F).Bv fluid oz!5Bf 2Be!/29.50where: 29.50 = weight of water (g/fluid oz) at 23 6 2.0C (73.4 6 3.6F).NOTE 1Contour of bead, undercut, or shoulder is optional.“L” Style “M” StyleAll-Purpose Thread (Plastic or Metal Closures) Modified Buttre

48、ss Thread (Plastic Closures)Threads/in. a b Threads/in. a b c12 in. 0.045 0.030 12 in. 0.051 0.030 0.016mm 1.14 0.76 mm 1.29 0.76 0.4112 in. 0.045 0.030 12 in. 0.051 0.030 0.016mm 1.14 0.76 mm 1.29 0.76 0.41NOTE 2Example Thread Nomenclature“L” Style: L15SP425 or“ M” Style M15SP425NOTE 3Corresponding

49、 dimensions and finish details are shown in Table 6.FIG. 4 SP 425 Finish Thread Cross SectionsD2911/D2911M 1668.1.6 Determine the volume in millilitres (fluid ounces) for each test specimen.8.1.7 Report the arithmetic average volume of the specimens tested as the bottle capacity of the batch or lot from which thesamples were chosen.8.2 Body Dimensions:8.2.1 Using a suitable micrometer, a vernier height gauge, or a scale, measure the height of the bottle.8.2.1.1 If the top of the finish is parallel to the base of