ASTM D1330-2004 Standard Specification for Rubber Sheet Gaskets《橡胶薄板垫圈的标准规范》.pdf
《ASTM D1330-2004 Standard Specification for Rubber Sheet Gaskets《橡胶薄板垫圈的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D1330-2004 Standard Specification for Rubber Sheet Gaskets《橡胶薄板垫圈的标准规范》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 1330 04Standard Specification forRubber Sheet Gaskets1This standard is issued under the fixed designation D 1330; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses ind
2、icates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers gaskets cut from sheet rubberthat are intended for g
3、eneral gasket applications on water, air,and low-pressure steam. They are not intended for use with oilsand strong acids.1.2 The values stated in SI units are to be regarded as thestandard.2. Referenced Documents2.1 ASTM Standards:2D 395 Test Methods for Rubber PropertyCompressionSetD 412 Test Metho
4、ds for Vulcanized Rubber and Thermo-plastic ElastomersTensionD 573 Test Method for RubberDeterioration in an AirOvenD 865 Test Method for RubberDeterioration by Heatingin Air (Test Tube Enclosure)D 1415 Test Method for Rubber PropertyInternationalHardnessD 2240 Test Method for Rubber PropertyDuromet
5、erHardnessD 3182 Practice for RubberMaterials, Equipment, andProcedures for Mixing Standard Compounds and Prepar-ing Standard Vulcanized SheetsD 3183 Practice for RubberPreparation of Pieces for TestPurposes From Products3. Materials and Manufacture3.1 Compounds furnished under this specification sh
6、all bemanufactured from natural rubber, reclaimed rubber, syntheticrubber, or mixtures thereof, together with added compoundingmaterials. The compound shall be suitably vulcanized. Thematerial shall be of a uniform quality and thickness, and shallhave a smooth or fine fabric surface.4. Color4.1 The
7、material shall be red or black as specified.5. Physical Properties5.1 This material shall conform to the requirements as tophysical properties prescribed in Table 1. Gaskets for contactwith water shall conform to Grade I requirements, gaskets forcontact only with air shall conform to Grade II, and g
8、askets forcontact with low-pressure steam shall conform to Grade III.6. Dimensional Tolerances6.1 The material shall conform to the requirements as todimensional tolerances prescribed in Table 2.7. Workmanship, Finish, and Appearance7.1 All materials and workmanship shall be in accordancewith good c
9、ommercial practice, and the resulting stock shall befree from porous areas, air pockets, foreign matter, or otherdefects affecting serviceability.8. Sampling8.1 When proof of conformance with this specification isrequired, the samples shall be taken from the finished productwhenever possible. When t
10、he thickness of the finished productis less than 1.6 mm (116 in.), the manufacturer shall, uponrequest of the purchaser, at the time of ordering, furnish asufficient number of test slabs or blocks prepared in accordancewith Practice D 3182 for the proper performance of therequired tests. The slabs o
11、r blocks shall be prepared from abatch of compound similar to that used in the lot. In the case ofgaskets cut from sheet, the manufacturer shall furnish a305-mm (12-in.) square sample of the uncut sheet. Unlessotherwise specified, a lot shall consist of all products of thesame thickness, submitted f
12、or inspection at the same time. Allsamples shall be prepared in accordance with Practices D 3182and D 3183.1This specification is under the jurisdiction of the ASTM Committee D11 onRubber and is the direct responsibility of Subcommittee D11.36 on Seals.Current edition approved Dec. 1, 2004. Publishe
13、d December 2004. Originallyapproved in 1954. Last previous edition approved in 2000 as D 1330 85 (2000).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standard
14、s Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9. Test Methods9.1 The properties enumerated in this specification shall bedetermined in accordance with the following methods, exceptas modif
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD13302004STANDARDSPECIFICATIONFORRUBBERSHEETGASKETS 橡胶 薄板 垫圈 标准规范 PDF

链接地址:http://www.mydoc123.com/p-509650.html