ASTM C530-2010 Standard Specification for Structural Clay Nonloadbearing Screen Tile《结构用粘土制非承重隔墙砖的标准规范》.pdf

《ASTM C530-2010 Standard Specification for Structural Clay Nonloadbearing Screen Tile《结构用粘土制非承重隔墙砖的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C530-2010 Standard Specification for Structural Clay Nonloadbearing Screen Tile《结构用粘土制非承重隔墙砖的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C530 10Standard Specification forStructural Clay Nonloadbearing Screen Tile1This standard is issued under the fixed designation C530; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers unglazed, structural clay, non-loadbearing screen tile.1.2 The property requirements of this specification apply at

3、the time of purchase. The use of results from testing of tileextracted from masonry structures for determining conform-ance or nonconformance to the property requirements (Section5) of this specification is beyond the scope of this standard.1.3 Tile covered by this specification are manufactured fro

4、mclay, shale, or similar naturally occurring substances andsubjected to a heat treatment at elevated temperatures (firing).The heat treatment must develop sufficient fired bond betweenthe particulate constituents to provide the strength and dura-bility requirements of this specification. (See firing

5、 and firedbond in Terminology C1232).1.4 The text of this specification references notes andfootnotes which provide explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the specification.1.5 The values stated in inch-pound u

6、nits are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2C67 Test Methods for Sampling and Testing Brick andStructural Clay TileC1232 Te

7、rminology of Masonry3. Grades3.1 Three grades of screen tile, based on relative durability,are covered as follows:NOTE 1Screen walls present many more exposed surfaces than otherbrick or tile walls, the question of durability and selection of grade may bemore critical in the screen walls. For this r

8、eason, these requirements aremore conservative than for brick.3.1.1 Grade SEScreen tile exhibiting a uniformly highresistance to disintegration by weathering or by freezing orthawing in the presence of moisture.3.1.2 Grade MEScreen tile exhibiting a moderate andsomewhat nonuniform resistance to weat

9、hering. Grade ME tileexhibit good durability in areas of mild to moderate exposurebut may not be adequate for severe exposures.3.1.3 Grade NEScreen tile for interior use (no exposure torain or freezing).3.2 When the grade is not specified, the requirements forGrade ME shall govern.3.3 Grade SE tile

10、may be accepted in lieu of Grades ME orNE. Grade ME tile may be accepted in lieu of Grade NE.4. Types4.1 Two types of screen tile, based on dimensional toler-ances, are covered as follows:4.1.1 Type STXScreen tile having a high degree of me-chanical perfection and minimum size variation.4.1.2 Type S

11、TAScreen tile exhibiting characteristic archi-tectural effects resulting from a larger degree of size variationthan obtainable with Type STX.4.2 When type is not specified, the requirements for TypeSTA shall govern.5. Physical Properties5.1 DurabilityScreen tile shall meet the properties pre-scribed

12、 in Table 1 for resistance to absorption.6. Dimensions and Permissible Variations6.1 The dimensions of screen tile units shall be specified bythe purchaser.NOTE 2Since screen tile are available in numerous sizes and shapes,the purchaser must specify these items. All sizes and shapes are notnecessari

13、ly available in all parts of the United States. Therefore, thespecifier should ascertain local availability before specifying a particularunit size or pattern.6.2 No screen tile shall have greater dimensional variationthan that permitted in Table 2.1This specification is under the jurisdiction of AS

14、TM Committee C15 onManufactured Masonry Units and is the direct responsibility of SubcommitteeC15.02 on Brick and Structural Clay Tile.Current edition approved June 1, 2010. Published June 2010. Originallyapproved in 1963. Last previous edition approved in 2005 as C53099 (2005). DOI:10.1520/C0530-10

15、.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this st

16、andard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Finish7.1 Tile surfaces shall be smooth, scored, combed, orroughened as specified by the purchaser.8. Color, Texture, and Pattern8.1 Color, texture, and pattern shall be specif

17、ied by thepurchaser. The texture and color range that will be visible in thefinished wall shall conform to an approved sample of at leastfour representative units.NOTE 3Tile colors vary with clay type and degree of burning. Colordoes not indicate tile classification unless it has been related to abs

18、orptionand strength by tests.Because a multitude of individual unit patterns and wall patterns areavailable, screen-wall strength in every direction may not be related to thecompressive strength of individual units. Designers are cautioned toinvestigate each wall design thoroughly and to provide suf

19、ficient expan-sion and pressure-relieving joints to eliminate induced forces that mightcreate critical stresses in screen-wall units.9. Optional Requirements9.1 If the purchaser desires closer dimensional tolerances,restrictions on chippage or roughness, or other requirementsnot specifically contain

20、ed in this specification, he must so statein a supplemental specification.10. Sampling and Testing10.1 Sample and test tile in accordance with Test MethodsC67.11. Inspection11.1 All tile shall be reasonably free from laminations andfrom defects that impair the placement, strength, or perma-nence of

21、the construction.12. Keywords12.1 clay; masonry construction; nonloadbearing tile; physi-cal properties; screen tile; shale; tileSUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since the last issue(C530 99 (2005) that may impact the use of this standa

22、rd. (Approved June 1, 2010.)(1) A statement on units was added as 1.5.(2) Terminology C43 was replaced with Terminology C1232.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are e

23、xpressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not rev

24、ised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you m

25、ay attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United St

26、ates. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also b

27、e secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Physical PropertiesGradeMaximum Water Absorption by 1-h Boiling,percentAverage of FiveTestsIndividualSE 10 12ME 14 16NE 20 24TABLE 2 Dimensions and Permissible VariationsSpecified Dimension,in. (mm)Maximum Permissible Variations fromSpecified Dimensions, Plus or Minus,in. (mm)TypeSTXTypeSTAUp to 4, incl. (101.6)332 (2.38)432 (3.18)Over 4 to 6 (101.6 to 152.4)432 (3.18)632 (4.76)Over 6 to 8 (152.4 to 203.2)532 (3.96)832 (6.35)Over 8 to 12 (203.2 to 304.8)732 (5.56)1032 (7.94)Over 12 (304.8)932 (7.14)1232 (9.52)C530 102