ASTM B483 B483M-2013 Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications《一般用途铝和铝合金拉制管材标准规格》.pdf

《ASTM B483 B483M-2013 Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications《一般用途铝和铝合金拉制管材标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B483 B483M-2013 Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications《一般用途铝和铝合金拉制管材标准规格》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B483/B483M 13Standard Specification forAluminum and Aluminum-Alloy Drawn Tube and Drawn Pipefor General Purpose Applications1This standard is issued under the fixed designation B483/B483M; the number immediately following the designation indicates the yearof original adoption or, in the

2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers aluminum and aluminum-alloydrawn tube and drawnpipe in strai

3、ght lengths and tube in coilsfor general purpose applications in the alloys (Note 2), andtempers shown in Tables 1 and 2. Coiled tubes are generallyavailable only as round tubes with a wall thickness notexceeding 0.083 in. 2.00 mm and only in non-heat-treatablealloys.NOTE 1For drawn seamless tubes,

4、see Specifications B210 andB210M, for tubes to be used in condensers and heat exchangers,Specifications B234 and B234M, and for seamless pipe, SpecificationB241/B241M. For extruded structural tube and pipe, see SpecificationB429.NOTE 2this specification use of the term alloy in the general senseincl

5、udes aluminum as well as aluminum alloy.1.2 Alloy and temper designations are in accordance withANSI H35.1/H35.1(M). The equivalent Unified Number Sys-tem alloy designations are those of Table 3 preceded byA9, forexample A91060 for aluminum 1060 in accordance withPractice E527.1.3 For acceptance cri

6、teria for inclusion of new aluminumand aluminum alloys in this specification, see Annex A2.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem may not be exact equiv

7、alents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in nonconformance with thestandard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of

8、this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a part of this specification to theextent referenced h

9、erein:2.2 ASTM Standards:2B210 Specification for Aluminum and Aluminum-AlloyDrawn Seamless TubesB210M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes (Metric)B234 Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes for Condensers and Heat Ex-changersB234M Specificatio

10、n for Aluminum and Aluminum-AlloyDrawn Seamless Tubes for Condensers and Heat Ex-changers (Metric)B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded TubeB429 Specification forAluminum-Alloy Extruded StructuralPipe and TubeB557 Test Methods for Tension Testin

11、g Wrought and CastAluminum- and Magnesium-Alloy ProductsB557M Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Products (Metric)B660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesiu

12、m ProductsB918 Practice for Heat Treatment of Wrought AluminumAlloysE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE215 Practice for Standardizing Equipment for Electromag-net

13、ic Testing of Seamless Aluminum-Alloy TubeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.03 onAluminum Alloy Wrought P

14、roducts.Current edition approved May 1, 2013. Published June 2013. Originallyapproved in 1983. Last previous edition approved in 2003 as B483/B483M-03,which was withdrawn January 2012 and reinstated in May 2013. DOI: 10.1520/B0483_B0483M-132For referenced ASTM standards, visit the ASTM website, www.

15、astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO

16、Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Tensile Property Limits, TubeA,BALLOYANDTEMPERSPECIFIEDWALLTHICKNESSin. mmTENSILE STRENGTH - ksi MPaElongation in 2 in. 50 mm or4 Diameter,Cmin, %JULTIMATEYIELDD(0.2% Offset),ksi MPaFULLSECTIONSPECIMENECut-Out SpecimenFmin. max. min.

17、max. In 50 mmIn 5 Diameter(5.65 =A)G1060F,I1060-O 0.010-0.5000.25-12.508.5 60 13.5 95 2.5 15 . . . . . . . . . .1060-H12 0.010-0.5000.25-12.5010.070 4.030 1060-H14 0.010-0.5000.25-12.5012.0 85 . . . . 10.0 70 . . . . . . . . . .1060-H18 0.010-0.5000.25-12.5016.0 110 . . . . 13.0 90 . . . . . . . . .

18、 .1060-H113K0.010-0.500.025-12.508.560 2.515 1100F,I1100-O 0.014-0.5000.36-12.5011.0 75 15.5 105 3.5 25 . . . . . . . . . .1100-H12 0.014-0.5000.36-12.5014.0 95 . . . . 11.0 75 . . . . . . . . . .1100-H14 0.014-0.5000.36-12.5016.0 110 . . . . 14.0 95 . . . . . . . . . .1100-H16 0.014-0.5000.36-12.50

19、19.0 130 . . . . 17.0 115 . . . . . . . . . .1100-H18 0.014-0.5000.36-12.5022.0 150 . . . . 20.0 140 . . . . . . . . . .1100-H113K0.014-0.5000.36-12.5011.075 3.525 3003F,I0.010-0.0240.25-0.6314.0 95 19.0 130 5.0 35 . . . . . . . . . .3003-O 0.025-0.0490.63-1.2014.0 95 19.0 130 5.0 35 . . . . 30 20 .

20、 .0.050-0.2591.20-6.3014.0 95 19.0 130 5.0 35 . . . . 35 25 . .0.260-0.5006.30-12.5014.0 95 19.0 130 5.0 35 . . . . . . 30 273003-H12 0.010-0.5000.25-12.5017.0 115 . . . . 12.0 85 . . . . . . . .0.010-0.0240.25-0.6320.0 140 . . . . 17.0 115 . . . . 3 . . . .3003-H14 0.025-0.0490.63-1.2020.0 140 . .

21、. . 17.0 115 . . . . 5 3 . .0.050-0.2591.20-6.3020.0 140 . . . . 17.0 115 . . . . 8 4 . .0.260-0.5006.30-12.5020.0 140 . . . . 17.0 115 . . . . . . . . . .0.010-0.0240.25-0.6324.0 165 . . . . 21.0 145 . . . . . . . . . .3003-H16 0.025-0.0490.63-1.2024.0 165 . . . . 21.0 145 . . . . 3 2 . .0.050-0.25

22、91.20-6.3024.0 165 . . . . 21.0 145 . . . . 5 4 . .0.260-0.5006.30-12.5024.0 165 . . . . 21.0 145 . . . . . . . . . .0.010-0.0240.25-0.6327.0 185 . . 24.0 165 . . . . 2 . . . .3003-H18 0.025-0.0490.63-1.2027.0 185 . . . . 24.0 165 . . . . 3 2 . .0.050-0.02591.20-6.3027.0 185 . . . . 24.0 165 . . . .

23、 5 3 . .0.260-0.5006.30-12.5027.0 185 . . . . 24.0 165 . . . . . . . . . .3003-H113K0.010-0.5000.25-12.5014.095 5.035 5050F,I5050-O 0.010-0.5000.25-12.7018.0 125 24.0 165 6.0 40 . . . . . . . . . .5050-H32 0.010-0.5000.25-12.7022.0 150 . . . . 16.0 110 . . . . . . . . . .5050-H34 0.010-0.5000.25-12.

24、7025.0 170 . . . . 20.0 140 . . . . . . . . . .B483/B483M 132TABLE 1 ContinuedALLOYANDTEMPERSPECIFIEDWALLTHICKNESSin. mmTENSILE STRENGTH - ksi MPaElongation in 2 in. 50 mm or4 Diameter,Cmin, %JULTIMATEYIELDD(0.2% Offset),ksi MPaFULLSECTIONSPECIMENECut-Out SpecimenFmin. max. min. max. In 50 mmIn 5 Di

25、ameter(5.65 =A)G5050-H36 0.010-0.5000.25-12.7027.0 185 . . . . 22.0 150 . . . . . . . . . .5050-H38 0.010-0.5000.25-12.7029.0 200 . . . . 24.0 165 . . . . . . . . . .5052F,I5052-O 0.010-0.4500.25-11.5025.0 170 35.0 240 10.0 70 . . . . . . . . . .5052-H2 0.010-0.4500.25-11.5031.0 215 . . . . 23.0 160

26、 . . . . . . . . . .5052-H34 0.010-0.4500.25-11.5034.0 235 . . . . 26.0 180 . . . . . . . . . .5052-H36 0.010-0.4500.25-11.5037.0 255 . . . . 29.0 200 . . . . . . . . . .5052-H38 0.010-0.4500.25-11.5039.0 270 . . . . 31.0 215 . . . . . . . . . .60616061-O 0.018-0.5000.45-12.50. . . . 22.0 150 . . .

27、. 14.0 95 15 15 130.025-0.0490.63-1.2030.0 200 . . . . 16.0 110 . . . . 16 14 . .6061-T4 0.050-0.2591.20-6.3030.0 200 . . . . 16.0 110 . . . . 18 16 . .0.260-0.5006.30-12.5030.0 200 . . . . 16.0 110 . . . . 20 18 160.025-0.0490.63-1.2030.0 200 . . . . 14.0 110 . . . . 16 14 . .6061-T42G,H0.050-0.259

28、1.20-6.3030.0 200 . . . . 14.0 110 . . . . 18 16 . .0.260-0.5006.30-12.5030.0 200 . . . . 14.0 110 . . . . 20 18 160.025-0.0490.63-1.2042.0 290 . . . . 35.0 240 . . . . 10 8 . .6061-T6 andT62G,H0.050-0.2591.20-6.3042.0 290 . . . . 35.0 240 . . . . 12 10 . .0.260-0.5006.30-12.5042.0 290 . . . . 35.0

29、240 . . . . 14 12 1060636063-O 0.018-0.5000.45-12.50. . . . 19.0 130 . . . . . . . . . . . . . .0.025-0.0490.63-1.2022.0 150 . . . . 10.0 70 . . . . 16 14 . .6063-T4 andT42G,H0.050-0.2591.20-6.3022.0 150 . . . . 10.0 70 . . . . 18 16 . .0.260-0.5006.30-12.5022.0 150 . . . . 10.0 70 . . . . 20 18 160

30、.025-0.0490.63-1.2033.0 230 . . . . 28.0 195 . . . . 12 8 . .6063-T6 andT62G,H0.050-0.2591.20-6.3033.0 230 . . . . 28.0 195 . . . . 14 10 . .0.260-0.5006.30-12.5033.0 230 . . . . 28.0 195 . . . . 16 12 106063-T83 0.025-0.2590.63-6.3033.0 230 . . . . 30.0 205 . . . . 5 . . . .6063-T831 0.025-0.2590.6

31、3-6.3028.0 195 . . . . 25.0 170 . . . . 5 . . . .6063-T832 0.025-0.0490.63-1.2041.0 285 . . . . 36.0 250 . . . . 8 5 . .0.050-0.2591.20-6.3040.0 275 . . . . 35.0 240 . . . . 8 5 . .0.051-0.5001.30-12.5050.0 345 . . . . 45.0 310 . . . . 10 8 . .62620.025-0.0490.63-1.2042.0 290 . . . . 35.0 240 . . .

32、. 10 8 . .6262-T6 andT62G,H0.050-0.2591.20-6.3042.0 290 . . . . 35.0 240 . . . . 12 10 . .0.260-0.5006.30-12.5042.0 290 . . . . 35.0 240 . . . . 14 12 10B483/B483M 133E607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen Atmosphere (With

33、drawn 2011)3E716 Practices for Sampling and Sample Preparation ofAluminum and Aluminum Alloys for Determination ofChemical Composition by Spectrochemical AnalysisE1251 Test Method for Analysis of Aluminum and Alumi-num Alloys by Spark Atomic Emission Spectrometry2.3 ANSI Standards:4H35.1/H35.1(M) Al

34、loy and Temper Designation SystemsH35.2 Dimensional Tolerances for Aluminum Mill ProductsH35.2M Dimensional Tolerances for Aluminum Mill Prod-ucts Metric2.4 Military Standard:5MIL-STD-129 Marking for Shipment and Storage2.5 Military Specifications:5AMS 2770 Heat Treatment of Wrought Aluminum AlloyPa

35、rtsAMS 2772 Heat Treatment of Aluminum Alloy Raw Mate-rials2.6 Federal Standard:5Fed. Std. No. 123 Marking for Shipment (Civil Agencies)3. Terminology3.1 DefinitionsRefer to Terminology B 881 for definitionsof product terms used in this specification.4. Ordering Information4.1 Orders for material to

36、 this specification shall include thefollowing information:3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from Standardizatio

37、n Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.TABLE 1 ContinuedALLOYANDTEMPERSPECIFIEDWALLTHICKNESSin. mmTENSILE STRENGTH - ksi MPaElongation in 2 in. 50 mm or4 Diameter,Cmin, %JULTIMATEYIELDD(0.2% Offset),ksi MPaFULLSECTI

38、ONSPECIMENECut-Out SpecimenFmin. max. min. max. In 50 mmIn 5 Diameter(5.65 =A)G6262-T9 0.025-0.3750.63-10.0048.0 330 . . . . 44.0 305 . . . . 5 4 3ASee Annex A1.BTo determine conformance to this specification each value for tensile strength and for yield strength shall be rounded to the nearest 0.1

39、ksi MPa and each value forelongation to the nearest 0.5 %, both in accordance with the rounding method of Practice E29.CElongation of full-section and cut-out sheet-type specimens is measured in 2 in.; of cut-out round specimens, in 4 specimen diameter.DYield strength to be determined only on straig

40、ht tube.ERound tube 2 inches or less in outside diameter and square tube 112 inches or less on a side are tested in full section unless the limitations of the testing machineprecludes the use of such a specimen.FFor round tube over 2 inches in diameter, for square tube over 112 inches on a side, for

41、 all sizes of tube other than round and square, or in those cases when a full sectionspecimen cannot be used, a cut-out specimen is used.GElongations in 50 mm apply for tube tested in full-section, for sheet type specimens for tubes having a flat wall, and for similar curved specimens for tubes havi

42、ng a curvedwall up to a maximum wall thickness of 12.50 mm. Elongations in 5D (5.65 =A), where D and A are diameter and cross-sectional area specimens, respectively, apply toround test specimens machined from wall thickness over 6.30 mm.HMaterial in the T42 or T62 tempers is not available from the m

43、aterial producers.IIn this alloy tube other than round is produced only in the F (as drawn) and O tempers. Properties for F temper are not specified or guaranteed.JFor specified wall thickness under 0.025 in. 0.63 mm elongation is not required.KThe H113 temper applies to other than round tube which

44、is fabricated from annealed round tube.TABLE 2 Tensile Property Limits, Drawn PipeA,B,CTemperPipe Size,DesignationTensile Strength, ksi MPaYield StrengthC(0.2% Offset),ksi MPa,minElongation, min, %min maxElongationin 2 in. or4 Diameter,Dmin, %In50 mmIn5 Diameter(5.65 =A)EAlloy 3003H18 Under 1 27.0 1

45、85 . 24.0 165 4 4 .H112 1 and over 14.0 95 . 5.0 35 25 25 22AThe basis for establishment of tensile property limits is shown in Annex A1.BFor purposes of determining conformance with this specification, each value for tensile strength and yield strength shall be rounded to the nearest 0.1 ksi, and e

46、ach valuefor elongation shall be rounded to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.CElongation of full-section and cut-out sheet-type specimens is measured in 2 in.; of round specimens, in 4 specimen diameter.DFor purposes of determining conformance with t

47、his specification, each value for ultimate strength and yield strength shall be rounded to the nearest 1 MPa, and eachvalue for elongation shall be rounded to the nearest 0.5%, both in accordance with the rounding-off method of Practice E29.EElongation in 50 mm apply for pipe tested in full-section and to sheet type specimens taken from pipes having a wall up to 12.50 mm thick. Elongation in 5D (5.65 =A)where D and A are diameter and cross-sectional area of the