ASTM B169 B169M-2005 Standard Specification for Aluminum Bronze Sheet Strip and Rolled Bar《铝青铜中厚板、薄板、带材和轧制棒材标准规范》.pdf

《ASTM B169 B169M-2005 Standard Specification for Aluminum Bronze Sheet Strip and Rolled Bar《铝青铜中厚板、薄板、带材和轧制棒材标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B169 B169M-2005 Standard Specification for Aluminum Bronze Sheet Strip and Rolled Bar《铝青铜中厚板、薄板、带材和轧制棒材标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 169/B 169M 05Standard Specification forAluminum Bronze Sheet, Strip, and Rolled Bar1This standard is issued under the fixed designation B 169/B 169M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification2establishes the requir

3、ements for Cop-per Alloy UNS Nos. C61300 and C61400 aluminum bronzesheet, strip, and rolled bar.1.2 The products made to this specification are commonlyused for drawing, forming, stamping, and bending applicationsand are not intended for electrical applications.NOTE 1The products produced under this

4、 general specification maybe used in many applications in which the individual requirements may betoo specific to be determined by normal physical or mechanical testing.Therefore, it may be advisable for the purchaser to submit samples ordrawings to the manufacturer to be assured that the product fu

5、rnished issuitable for the intended application.NOTE 2Refer to Specification B 171/B 171M for plate product.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall

6、 be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 The following documents in the current Book of Stan-dards form a part of this specification to the extent referencedherein:2.2 ASTM Standards:3B 171/B 1

7、71M Specification for Copper Alloy Plate andSheet for Pressure Vessels, Condensers and Heat Exchang-ersB 248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip and RolledBarB 248M Specification for General Requirements forWrought Copper and Copper-Alloy Pla

8、te, Sheet, Strip andRolled Bar MetricB 601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB 846 Terminology for Copper and Copper AlloysE8 Test Methods for Tension Testing of Metallic MaterialsE8M Test Methods for Tension Testing of Metallic Mate-rials MetricE54 Te

9、st Methods for Chemical Analysis of SpecialBrasses and Bronzes4E62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)E 290 Test Methods for Bend Testing of Material forDuctilityE 478 Test Methods for Chemical Analysis of CopperAlloys3. General Requirements3.1 The fol

10、lowing sections of Specifications B 248 orB 248M form a part of this specification:3.1.1 Terminology,3.1.2 Workmanship, Finish and Appearance,3.1.3 Sampling,3.1.4 Significance of Numerical Limits,3.1.5 Inspection,3.1.6 Rejection and Rehearing,3.1.7 Certification,3.1.8 Mill Test Reports,3.1.9 Packagi

11、ng and Package Marking,3.1.10 Supplementary Requirements.3.2 In addition, when a section with a title identical to thatreferenced in 3.1 appears in this specification, it containsadditional requirements which supplement those appearing inSpecifications B 248 or B 248M.1This specification is under th

12、e jurisdiction ofASTM Committee B05 on Copperand CopperAlloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved Oct. 1, 2005. Published November 2005. Originallyapproved in 1941. Last previous edition approved in 2001 as B 169/B 169M 01.2For A

13、SME Boiler and Pressure Vessel Code applications, see related Specifi-cation SB-169 in Section II of that code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the s

14、tandards Document Summary page onthe ASTM website.4Withdrawn.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Terminology4.1 For definitions of terms related to copp

15、er and copperalloys, refer to Terminology B 846.5. Ordering Information5.1 Orders for products under this specification shouldinclude the following information:5.1.1 ASTM designation and year of issue (for example,B 169/B 169M 05),5.1.2 Copper Alloy UNS No. (for example, C61300),5.1.3 Temper (for ex

16、ample, Section 8),5.1.4 Dimensions, thickness, and width (for example, Sec-tion 12),5.1.5 Length,5.1.6 How furnished, flat or rolls,5.1.7 Total weight, each size,5.1.8 When product is purchased for ASME Boiler andPressure Vessel Code Application, and5.1.9 When product is purchased for agencies of th

17、e U.S.government.5.2 The following options are available and should bespecified when required:5.2.1 Type of edge (for example, slit, sheared, sawed, and soforth),5.2.2 Heat identification or traceability details,5.2.3 Bend test,5.2.4 Certification, and5.2.5 Mill test report.6. Materials and Manufact

18、ure6.1 MaterialThe material of manufacture shall be fromcast slabs (also termed cakes or ingots) of Copper Alloy UNSNumbers C61300 or C61400 of such purity and soundness asto be suitable for processing into the products prescribedherein.6.2 ManufactureThe products shall be manufactured bysuch hot-wo

19、rking, cold-working, and annealing processes as toproduce a uniform wrought structure in the finished product.The product shall be hot or cold rolled to finish gage andsubsequently annealed, if required, to meet the temper proper-ties invoked.6.2.1 EdgesSlit edges shall be furnished unless otherwise

20、specified in the contract or purchase order.7. Chemical Composition7.1 The specified copper alloy shall conform to the require-ments of Table 1.7.1.1 These composition limits do not preclude the presenceof unnamed elements. Limits may be established and analysisrequired for unnamed elements by agree

21、ment between thesupplier and the purchaser.7.2 When all elements in Table 1 for the specified alloy aredetermined, the sum of the results shall be:Copper Alloy UNS No. Sum of Results % min.C61300 99.8C61400 99.58. Temper8.1 Products in both alloys are available in the followingtempers as defined in

22、Classification B 601: annealed tempersO25, O60, and hot-rolled temper M20.NOTE 3Inquiry should be made to the supplier concerning theavailability of the specific temper required.9. Mechanical Property Requirements9.1 The product furnished shall conform to the requirementsof Table 2 or Table 3 for th

23、e specified alloy, temper, anddimensions prescribed.TABLE 1 Chemical RequirementsElementComposition,%Copper Alloy UNS No.C61300AC61400Copper (including silver) remainder remainderLead, max 0.01 0.01Iron 2.03.0 1.53.5Zinc, max 0.10 0.20Aluminum 6.07.5 6.08.0Manganese, max 0.20 1.0Phosphorus, max 0.01

24、5 0.015Silicon, max 0.10 .Tin 0.200.50 .Nickel (including cobalt), max 0.15 .AWhen the product is for subsequent welding applications and is so specified bythe purchaser, chromium shall be 0.05 % max, cadmium 0.05 % max, zirconium0.05 % max, and zinc 0.05 % max.TABLE 2 Tensile Requirements (Inch-Pou

25、nd)CopperAlloyUNS No.Temper DesignationAThickness, in. Width, in.TensileStrengthmin, ksiBYield Strength at0.5 % ExtensionUnder Load,min, ksiBYield Strength at0.2 % ExtensionUnder Load,min, ksiBElongationin2in.,min,%Standard FormerC61300 O25, O60, or M20 soft12 and under all widths 75 36 34 35Over12

26、to 2, incl all widths 72 32 30 35Over 2 to 5, incl all widths 65 28 26 35C61400 O25, O60, or M20 soft12 and under all widths 72 32 30 35Over12 to 2, incl all widths 70 30 28 35Over 2 to 5, incl all widths 65 28 26 35AStandard designations defined in Classification B 601.Bksi = 1000 psi.B 169/B 169M

27、05210. Bending Requirements10.1 When specified in the contract or purchase order, thetest specimen shall withstand being bent cold perpendicular tothe direction of rolling (rightway bend) through 120 around amandrel whose radius is equal to the thickness of the product.When the outside surface of th

28、e bend is examined with anunaided eye, no sign of fracturing shall be observed.11. Purchases for U.S. Government Agencies11.1 When specified in the contract or purchase order,product purchased for agencies of the U.S. government shallconform to the special government stipulations in the Supple-menta

29、ry Requirements section of Specifications B 248 orB 248M.12. Dimensions, Mass, and Permissible Variations12.1 The dimensions and tolerances for material describedby this specification shall be as specified in the current editionof Specifications B 248 or B 248M.12.1.1 Thickness12.1.2 Width:12.1.2.1

30、Slit Metal and Slit Metal with Rolled Edges12.1.2.2 Square Sheared Metal12.1.2.3 Sawed Metal12.1.3 Length:12.1.3.1 Length Tolerances for Straight Lengths12.1.3.2 Schedule for Minimum Lengths and MaximumWeights of Ends for Specific Lengths with Ends, and StockLengths with Ends12.1.3.3 Length Toleranc

31、e for Square Sheared Metal12.1.3.4 Length Tolerances for Sawed Metal12.1.4 Straightness:12.1.4.1 Slit Metal or Slit Metal Either Straightened or EdgeRolled12.1.4.2 Square Sheared Metal12.1.4.3 Sawed Metal12.1.5 Edges:12.1.5.1 Square Edges12.1.5.2 Rounded Corners12.1.5.3 Rounded Edges12.1.5.4 Full Ro

32、unded Edges13. Number of Tests and Retests13.1 Tests:13.1.1 Chemical AnalysisComposition shall be deter-mined as the average of at least two replicate determinationsfor each element in Table 1 for the specified alloy.13.1.2 Mechanical PropertiesTensile strength, yieldstrength, and elongation shall b

33、e reported as the average ofresults from at least two specimens.13.1.3 Bending RequirementsTwo specimens shall betested and both shall pass.13.2 Retests:13.2.1 Chemical AnalysisShould the results for one ormore of the elements in the specified alloy fail to conform withthe requirements in Table 1, a

34、 retest may be made with a newcomposite made up from the pieces originally selected.13.2.2 Mechanical PropertiesShould the test results ob-tained from the specified product fail to conform to therequirements of Table 2, a retest shall be permitted on twospecimens made from the remaining pieces selec

35、ted.13.2.3 Referee (Umpire) TestsRefer to section entitled“Rejection and Rehearing” in Specifications B 248 or B 248M.14. Specimen Preparation14.1 Chemical AnalysisPreparation of the analyticalspecimen shall be the responsibility of the reporting laboratory.14.2 Mechanical Properties:14.2.1 Tensile

36、and yield test specimens shall be prepared inaccordance with Test Methods E8or E8M.14.2.1.1 The tensile test specimen shall be taken so that thelongitudinal axis is parallel to the direction of rolling.14.3 Bend TestBend test specimens shall be prepared asdirected in Test Method E 290.15. Test Metho

37、ds15.1 Chemical Analysis:15.1.1 The chemical composition shall be determined, incase of disagreement, as follows:TABLE 3 Tensile Requirements (SI)CopperAlloyUNS No.Temper DesignationAThickness, mm Width, mmTensileStrengthmin, MPaYield Strength at0.5 % ExtensionUnder Load,min, MPaYield Strength at0.2

38、 % ExtensionUnder Load,min, MPaElongationin2in.,min,%Standard FormerC61300 O25, O60, or M20 soft 12.0 and under all widths 515 250 235 35Over 12.0 to50.0, inclall widths 495 220 205 35Over 50.0 to 140inclall widths 450 195 180 35C61400 O25, O60, or M20 soft 12.0 and under all widths 495 220 205 35Ov

39、er 12.0 to50.0, inclall widths 485 205 195 35Over 50.0 to 140inclall widths 450 195 180 35AStandard designations defined in Classification B 601.B 169/B 169M 053ElementASTMMethodCopper E 478Iron E 478Lead E 478 (AA)Zinc E 478 (titrimetric)Aluminum E 478Manganese E62Phosphorus E62Silicon E 54 (sulfur

40、ic acid)Tin E 478 (photometric)Nickel E 478 (photometric)15.1.2 Test method(s) for the determination of element(s)required by contractual or purchase order agreement shall be asagreed upon between the supplier and purchaser.15.2 Other Tests:15.2.1 The product furnished shall conform with the me-chan

41、ical and other requirements enumerated in this specifica-tion when tested in accordance with the following appropriatemethod:Test MethodTensile strength E8Yield strength E8Elongation E8Bending E 29015.2.1.1 Yield strength shall be determined in accordancewith the “Extension-Under Load Method” of Tes

42、t MethodsE8.15.2.1.2 Elongation shall be determined as specified in thefirst two subsections of the section of Test Methods E8,orE8M, entitled “Elongation.”15.2.1.3 Test results are affected by variations in speed oftesting. A considerable range of testing speed is permitted. Therate of stressing to

43、 the yield strength should not exceed 100ksi/min 690 MPa/min. Above the yield strength, the move-ment per minute of the testing machine head under load shouldnot exceed 0.5 in./in 0.5 mm/mm.16. Certification16.1 When the contract or purchase order specifies theproduct to be for ASME Boiler and Press

44、ure Vessel applica-tion, certification is mandatory.17. Keywords17.1 aluminum bronze; aluminum bronze rolled bar; alumi-num bronze sheet; aluminum bronze stripSUMMARY OF CHANGESCommittee B05 has identified the location of selected changes to this standard since the last issue(B 169/B 169M 01) that m

45、ay impact the use of this standard. (Approved Oct. 1, 2005.)(1) For clarity, the table on mechanical properties (TensileRequirements) was broken up into two tables, Table 2 andTable 3. Table 2 is for the inch-pound system, and Table 3 is forthe SI system.(2) Two rationalized metric values for C61300

46、 were changedin Table 3. The 0.5 % Extension Yield Strength for “soft” 12.0and under was changed from 225 to 250 MPa. Also, 12.0 to50.0 “soft” 0.2 % Offset Yield Strength was changed from 210to 205 MPa. These values are more consistent with otherrationalized metric values in the specification.(3) Mi

47、nor editorial changes were made throughout, which donot impact the usage of this standard.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination

48、of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn

49、. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-