ASD-STAN PREN 2413-1994 Aerospace Series Bolts Thin Hexagonal Head Close Tolerance Shank Short Thread in Alloy Steel Cadmium Plated Classification 1 100 MPa (at Ambient Temperatur.pdf

《ASD-STAN PREN 2413-1994 Aerospace Series Bolts Thin Hexagonal Head Close Tolerance Shank Short Thread in Alloy Steel Cadmium Plated Classification 1 100 MPa (at Ambient Temperatur.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 2413-1994 Aerospace Series Bolts Thin Hexagonal Head Close Tolerance Shank Short Thread in Alloy Steel Cadmium Plated Classification 1 100 MPa (at Ambient Temperatur.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、CEN PRENr2413 94 m 3404589 O062325 603 m Edition approved for publication 1994-02-28 AECMA STANDARD NORME AECMA AECMA NORM C3 Chairman M. Arena Comments should be sent within six months after the date of publication to AECMA Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Ced

2、ex - FRANCE prEN 2413 Edition P 2 February 1994 DIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - F-92138 Issy-les-Moulineaux Cedex - Tl. (I) 47.36.98.76 UDC : 621.882.21 1 : 629.7 Supersedes issue PI February 1987 Descriptors : Air

3、craft industry, aircraft equipement, hinge pin, alloy steel, cadmium, screw thread, specification, characteristic, dimension, mass, dimensional tolerance, surface treatment, designation, marking ENGLISH VERSION Aerospace series Bolts, shouldered, thin hexagonal head, close tolerance shank, short thr

4、ead, in alloy steel, cadmium plated Classification : 1 I00 MPa (at ambient temperature) / 235 OC Srie arospatiale Axes tte hexagonale basse, tige tolrance serre, filetage court, en acier alli, cadmis Classification : 1 100 MPa ( temprature ambiante) / 235 OC Luft- und Raumfahrt Sechskant-Pacchrauben

5、, kleiner Kopf, kurzes Gewinde, aus legiertem Stahl, verkadmet Klasse : 1 100 MPa (bei Raumtemperatur) / 235 OC This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for

6、the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this prestandard, the technical content shall not be changed to an extent that interchangeability is affected,

7、physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for St

8、andardization) for formal vote. CEN PRENx2413 74 W 340q589 0062326 54T W Page 2 prEN 2413 : 1994 Foreword The equivalent text of this standard was submitted for Official Services ballot until 1st July 1993. Comments received from Official Services were incorporated following decisions taken by Techn

9、ical Committee C 3 during its 65th meeting on 15th October 1993. CEN PRENd2433 9Li 3404589 0062327 4Bb Page 3 prEN 2413 : 1994 1 Scope This standard specifies the characteristics of bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in alloy steel, cadmium plated. Classific

10、ation : 1 100 MPa ) / 235 OC *) These bolts are intended to be used with washers EN 241 4 and nuts EN 241 5. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in

11、 the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred t

12、o applies. IS0 3353 IS0 5855-2 IS0 7689 IS0 791 3 EN 2000 EN 2133 EN 2137 EN 2414 EN 2415 EN 2424 EN 2442 EN 2446 EN 2475 EN 2793 EN 3042 EN 4016 TR 3775 Aerospace - Rolled threads for bolts - Lead and runout requirements Aerospace - MJ threads - Part 2 : Limit dimensions for bolts and nuts Aerospac

13、e - Alloy steel bolts with strength classification 1 100 MPa and MJ threads - Procurement specification Aerospace - Bolts and screws, metric - Tolerances of form and position Aerospace series - Quality assurance - EN aerospace products - Approval of the quality system of manufacturers Cadmium platin

14、g of steels with maximum specified tensile strength equal to or less than 1 450 MPa and copper and copper alloys - Aerospace series 3, Steel FE-PL75 - 1 1 O0 MPa I R, I 1 250 MPa - Bars De I 1 O0 mm - Aerospace series 3, Aerospace series - Washers, chamfered, with counterbore, in alloy steel, cadmiu

15、m plated 4, Nuts, hexagon, slottedlcastellated, thin, in steel, cadmium plated - Classification : 900 MPa i 235 OC - Aerospace series 3, Aerospace series - Identification marking of standard fasteners 31 Steel FE-PL71 1 - 1 100 MPa 5 R, I 1 300 MPa - Bars and wires De I 25 mm - Aerospace series 3, S

16、teel FE-PL45 - 1 100 MPa I R, I 1 300 MPa - Bars De I 25 mm - Aerospace series 3, Steel FE-PL74 - 1 1 O0 MPa I R, I 1 300 MPa - Bars De I 1 O0 mm - Aerospace series 3, Aerospace series - Phosphating of ferrous alloys Aerospace series - Quality .assurance - EN aerospace products - Qualification proce

17、dure Aerospace series - Oversized bolts 5, Aerospace series - Bolts and pins - National materials 6, 1) Minimum tensile strength of the material at ambient temperature 2) Maximum temperature that the bolt can withstand without continuous change in its original characteristics, after return to ambien

18、t temperature. The maximum temperature is determined by the surface treatment. 3) Published as AECMA Standard at the date of publication of this standard 4) Published as AECMA Prestandard at the date of publication of this standard 5) In preparation at the date of publication of this standard 6) Pub

19、lished as AECMA Technical Report at the date of publication of this standard CEN PREN*2433 94 m 3404589 O062328 332 m Page 4 prEN 241 3 : 1994 3 Required characteristics 3.1 Configuration - Dimensions - Masses See figures 1 and 2 and table 1. Dlmensions and tolerances are expressed in millimetres an

20、d apply after surface treatment. 3.2 IS0 7913 3.3 Materials EN 2137, EN 2442, EN 2446, EN 2475 Tolerances of form and position or TR 3775 (alloy steel, classification 1 100 MPa) 3.4 Surface treatment 3.4.1 External surfaces EN 2133, 6 pm to 10 pm on all surfaces which can be contacted by a 20 mm dia

21、meter ball. On all other surfaces, a continuous deposit shall be present, but no value is specified. Black colour option : code B 3.4.2 Hole 0 D3 EN 2793 class C, plus anti-corrosion priming coat at the manufacturers option CEN PRENx2433 94 3404589 0062329 259 M -3 n e Page 5 prEN 241 3 : 1994 Y- r

22、1 IS0 3353 i Values in micrometres apply prior to surface treatment. VI ?8/1 Break sharp edges 0,l to 0,4 , , Conforms io IS0 3353 r L1 - For non-quoted dimensions, see figure 2. Figure 1 - Configuration for diameter codes 050 and O60 Lq- (=LI ) c 1 hole IZI D5 Conforms to IS0 3353 w Marking r7 Figu

23、re 2 - Configuration for diameter codes 080 to 250 Page 6 prEN 241 3 : 1994 c; Q W O v) W N O r - 5 L 3 O c + W C O r Q W W Q 9 w - o i 5 ED C 01 W O c v) Q C O Q v) - 5 L 8 o W U O o 0 C W al 5 - E E E CJ O v) w C y E 2 o C ol C v) 3 C al v) O o W D .- .- CEN PRENm24L3 94 3404589 OObZL3L 907 Descri

24、ption block Page 7 prEN 2413 : 1994 Identity block 4 Designation EXAMPLE : NOTE : If necessary, the code 19005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style A (see figure 2) 6 Technical specification IS0 7689, with the following modifications : 6.1 Ap

25、proval of manufacturers EN 2000 6.2 Qualification of bolts EN 3042 6.3 Other modified requirements - Head may be manufactured by removal of material ; - In the case of forging, heat treatment shall be carried out after forging ; - Requirement for machining only concerns forged heads. 6.4 Requirements deleted - Cold rolling - Tensile strength - Double shear strength - Tension fatigue strength - Head to shank grain flow and fillet work effect 7 Oversized bolts EN 4016