ANSI ABMA 199-2014 Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance.pdf

《ANSI ABMA 199-2014 Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance.pdf》由会员分享，可在线阅读，更多相关《ANSI ABMA 199-2014 Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 Rolling bearings Thrust bearings Geometrical product specification (GPS) and tolerance valuesTolerances ANSI/ABMA/ISO 199-2014 Sponsor American Bearing Manufacturers Association ANSI/ABMA/ISO 199-2014 (Identical Adoption of ISO 199:2014) Copyright American Bearing Manufacturers Association, Inc. Ne

2、ither part of the printed publication, nor any part of the electronic tile may be reproduced or transmitted in any form, including transmittal by e-mail, by file transfer protocol (FTP), or by being made part of a network-accessible system, without the prior written permission of the copyright owner

3、. ABMA FOREWORD (This foreword is not part of ANSI/ABMA/ISO 199-2014.) IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of developing International Standards is carried out through IS0 technical committees.

4、Every member body interested in a subject for which a technical committee has been authorized has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. The text is approved as an International S

5、tandard if a two-thirds majority of the P (participating)-members of the TC/SC are in favor and not more than one-quarter of the total number of votes cast are negative. International Standard 199:2014 was prepared by Technical Committee ISO/TC 4, Rolling Bearings. This standard was processed and ap

6、proved for submittal to ANSI for national adoption by Accredited Standards Committee B3. Committee approval of the national adoption of this standard does not necessarily mean that all committee members voted for its adoption. Suggestions for the improvement of this standard gained through experienc

7、e with its use will be welcomed. These suggestions should be sent to: ASC B3 Secretariat American Bearing Manufacturers Association 2025 M Street, N.W., Suite 800 Washington, DC 20036 ISO 2014Rolling bearings Thrust bearings Geometrical product specification (GPS) and tolerance valuesRoulements Bute

8、s Spcification gomtrique des produits (GPS) et valeurs de tolranceINTERNATIONAL STANDARDISO199Fourth edition2014-07-15Reference numberISO 199:2014(E)Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Dow

9、nloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, elec

10、tronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. +

11、41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale

12、or distribution.ISO 199:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Symbols 15 Limit deviations and tolerance values . 75.1 General . 75.2 Tolerance class Normal 85.3 Tolerance class 6 . 105.4 Tolerance

13、 class 5 . 125.5 Tolerance class 4 . 14Annex A (informative) Symbols and terms as given in ISO 199:2005 in relationship to new descriptions given in this document .16Annex B (informative) Example of drawing indications of characteristics with specification for thrust bearings 18Annex C (informative)

14、 Illustration of ISO 1132-14and ISO 14405-1 terms and definitions .20Annex D (informative) Description with illustrations for specification modifiers of linear sizes 25Bibliography .33Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members fo

15、r further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standa

16、rds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also tak

17、e part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In par

18、ticular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of

19、this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see w

20、ww.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to t

21、he WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 4, Rolling bearings, Subcommittee SC 4, Tolerances, tolerance definitions and symbols (including GPS).This fourth edition cancel

22、s and replaces the third edition (ISO 199:2005), which has been technically revised.iv ISO 2014 All rights reservedCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for

23、 additional sale or distribution.ISO 199:2014(E)IntroductionThis International Standard is a machine element geometry standard as defined in the geometrical product specification (GPS) system as presented in master plan of ISO/TR 14638.10The fundamental rules of ISO/GPS given in ISO 80157apply to th

24、is International Standard and the default decision rules given in ISO 14253-18apply to the specifications made in accordance with this International Standard, unless otherwise indicated.The connection between functional requirements, measuring technique and measuring uncertainty is always intended t

25、o be considered. The traditionally used measuring technique is described in ISO 1132-2.5For measurement uncertainty it is intended that ISO 14253-29should be considered. ISO 2014 All rights reserved vCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to comm

26、ittee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.Copyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not

27、for additional sale or distribution.Rolling bearings Thrust bearings Geometrical product specification (GPS) and tolerance values1 ScopeThis International Standard specifies dimensional characteristics, limit deviations from nominal values, and tolerance values to define the interface (except chamfe

28、rs) of thrust rolling bearings. Nominal boundary dimensions are defined in ISO 1041.This International Standard is not applicable to certain thrust bearings (e.g. thrust needle roller bearings) or for particular fields of application (e.g. special thrust precision bearings). Tolerances for such bear

29、ings are given in the relevant International Standards.Chamfer dimension limits are given in ISO 5823.2 Normative referencesThe following documents in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

30、 applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5593, Rolling bearings VocabularyISO 14405-1, Geometrical product specifications (GPS) Dimensional tolerancing Part 1: Linear sizesISO/TS 17863, Geometrical product specification (G

31、PS) Geometrical tolerancing of moveable assemblies3 Terms and definitionsFor the purposes of this document, the terms and definitions in ISO 5593, ISO 14405-1, and ISO/TS 17863 apply.4 SymbolsTo express that the ISO/GPS system, ISO 8015 7is applied, the dimensional characteristics shall be included

32、in the technical product documentation (for example on the drawing). The dimensional specifications, associated to these characteristics, are described in Table 1 and Figures 1 to 4.Descriptions for symbols are in accordance with GPS terminology; relationships with traditional terms are described in

33、 Annex A.A tolerance value associated to a characteristic is symbolized by t followed by the symbol for characteristic, for example, tdmp.In this International Standard, the ISO default specification operator for size is in accordance with ISO 14405-1, i.e. the two-point size is valid. Some specific

34、ation modifiers are described in Annex D.The detailed definitions for terms in ISO 14405-1 and traditional terms in ISO 1132-14are not fully equal, for differences, see Annex C.INTERNATIONAL STANDARD ISO 199:2014(E) ISO 2014 All rights reserved 1Copyright by ISO. Reproduced by ANSI with permission o

35、f and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)Table 1 Symbols for nominal sizes, characteristics and specification modifiersSymbol for nominal size aSymbol for charact

36、eristic aGPS symbol and specification modifier b cDescription dSee Figured Nominal bore diameter of shaft washer, single-direction bearing1; 2dmpACSDeviation of a mid-range size (out of two-point sizes) of shaft washer bore diameter in any cross-section from its nominal size1; 2VdspACSRange of two-p

37、oint sizes of shaft washer bore diameter in any cross-section1; 2d2Nominal bore diameter of central shaft washer, double-direction bearing3; 4d2mpACSDeviation of a mid-range size (out of two-point sizes) of central shaft washer bore diameter in any cross-section from its nominal size3; 4Vd2spACSRang

38、e of two-point sizes of central shaft washer bore diameter in any cross-section3; 4D Nominal outside diameter of housing washer1; 2; 3; 4DmpACSDeviation of a mid-range size (out of two-point sizes) of housing washer outside diameter in any cross-section from its nominal size1; 2; 3; 4VDspACSRange of

39、 two-point sizes of housing washer outside diameter in any cross-section1; 2; 3; 4T Nominal assembled bearing height, single-direction bearing1; 2TsGNeDeviation of minimum circum-scribed size of assembled bear-ing height from its nominal size, single-direction bearing1; 22 ISO 2014 All rights reserv

40、edCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)Table 1 (continued)Symbol for nomi-nal sizeaSymbol for characteri

41、sticaGPS symbols and specification modifiersb cDescriptionsdSee Fig-ureT1Nominal assembled bearing height, double-direction bearing3; 4T1sGNeDeviation of minimum circum-scribed size of assembled bearing height from its nominal size, double-direction bearing3; 4Se fThrust cylindrical roller bear-ings

42、: range of two-point sizes of thickness between housing washer raceway and the back face2; 4ALSSNLSThrust ball bearings: range of minimum spherical sizes between the raceway and the opposite back face of the housing washer, obtained from any longitudinal section which includes the housing washer out

43、side surface axis1; 3Si fThrust cylindrical roller bear-ings: range of two-point sizes of thickness between shaft washer raceway and the back face2ALSSNLSThrust ball bearings: range of minimum spherical sizes between the raceway and the opposite back face of the shaft washer, obtained from any longi

44、tudinal section which includes the shaft washer bore axis1aSymbols as defined in ISO 1524112except for the format used.bSymbols as defined in ISO 14405-1.cSpecification modifier shall not be indicated on a drawing, because two-point size is the default specification modifier for size.dDescriptions b

45、ased on ISO 14405-1.esymbols for direction of gravity Gaccording to ISO/TS 17863, see Figures 1 to 4.fApplies only to thrust ball bearings with 90 contact angle and thrust cylindrical roller bearings with 90 contact angle.The indications in Figures 1 to 4 illustrate the correlation of interface dime

46、nsions and corresponding dimensional tolerance symbols.NOTE Figures 1 to 4 are drawn schematically and do not necessarily show all design details.Two examples of a real drawing indication are given in Annex B. ISO 2014 All rights reserved 3Copyright by ISO. Reproduced by ANSI with permission of and

47、under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)ACStVdsptVDspACStdmpACSd T tTsGN 1 2tDmpACSDKMGG2GG1tSet SiSN K LS ALSSN M LS ALS121 =G1 or G2=2the rolling elements shall be i

48、n contact with both shaft and housing washer racewaysKey1 housing washer2 shaft washerFigure 1 Size specification for single-direction bearing Thrust ball bearingACSt SitVDspACSACStVdsptSetdmpd ACStDmpDT tTsGN 1 2GG2GG1121 =G1 or G2=2the rolling elements shall be in contact with both shaft and housi

49、ng washer racewaysKey1 housing washer2 shaft washerFigure 2 Size specification for single-direction bearing Thrust cylindrical roller bearing4 ISO 2014 All rights reservedCopyright by ISO. Reproduced by ANSI with permission of and under license from ISO. Licensed to committee members for further standardization only. Downloaded 7/29/2014 2:18 PM. Not for additional sale or distribution.ISO 199:2014(E)112MtVDspACStVDspACST tT1sGN121tDmpACSDtDmp ACSDGG2GG1Lt ACSd 2 d2mptVd2spACS tS