AECMA PREN 2082-1-1986 Aerospace Series Aluminium Alloy Forging Stock and Forgings - Technical Specification - Part 1 - General Requirements Edition 1《航空航天系列.铝合金锻坯和锻件 技术规范.第1部分 一般要.pdf

《AECMA PREN 2082-1-1986 Aerospace Series Aluminium Alloy Forging Stock and Forgings - Technical Specification - Part 1 - General Requirements Edition 1《航空航天系列.铝合金锻坯和锻件 技术规范.第1部分 一般要.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2082-1-1986 Aerospace Series Aluminium Alloy Forging Stock and Forgings - Technical Specification - Part 1 - General Requirements Edition 1《航空航天系列.铝合金锻坯和锻件 技术规范.第1部分 一般要.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、A.E.C.M.A. STANDARD NORME A.E.C.M.A. A.E.C.M.A. NORM prEN2082 Part 1 Edition 1 September 1986 _L_? AECMA PREN2082-01 86 m 10123LL 0007672 7 mL , Y- r o - ENGL SH VERSION -erOsPace series Aluminium alloy forging stock and forgings - Technical specification - Part 1 - General requirements Srie arospat

2、iale Produits destins la forge, pices forges et pices matrices en alliages daluminium - Spcification technique - Partie 1 - Exigences gnrales Luft- und Raumfahrt Schmiedevormaterial und Schmiedestcke aus Aluminiumlegierung - Technische Lieferbedingungen - Teil 1 - Allgemeine Anforderungen This indus

3、trial standard for the aerospace sector has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on yellow paper in three equivalent versions (English, French, German). It will be submitted to CEN (European Committee for Sta

4、ndardization) as a draft European Standard. Approved by The equivalent versions in French and German languages be supplied by B.NA.E., 8, rue Moreau-Vauthier -li- I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo rep

5、roduction or networking permitted without license from IHS-,-,-prEN2082-1 Page 2 1 2 3 4 5 6 7 8 9 10 11 12 13 Contents Scope Field of application References Defini ti ons Manufacture Traceabi 1 i ty Freedom from defects Testing Marking Acceptance Inspection and testing report Packing Wording of ord

6、ers Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2082-01 6 10L2311 000767Ll O prEN2082-1 Page 3 1 Scope This standard defines the general

7、 requirements-for manufacture, inspection and testing of aluminium alloy forging stock and forgings. Particular requirements applicable to forging stock, pre-production forgings and production forgings are defined in EN2082-2 and EN2082-3 respectively. The three Standards EN2082-1, EN2082-2 and EN20

8、82-3 define the inspection level and the sampling frequencies tc.be applied unless otherwise specified on the drawing, order or inspection schedule. 2 Field of appiication Unless otherwise specified on the drawing, order or inspection schedule this standard shall be applied when referenced in the re

9、levant EN material standarcis. It is applicable to : - Forging stock (EN2082-2), - Hand forgings including forged blocks and rings, die forgings and rolled rings (EN2082-3), hereafter described as “forgings“. By agreement between the purchaser and the manufacturer, it may also be applied to other ma

10、terials or delivery conditions not covered by EN standards. The agreements shall be formalized by reference to this standard on the drawing, order or inspection schedule. 3 References .EN2078, Definitions of manufacturing schedule inspection schedule and inspection report - General-definitions - Aer

11、ospace series EN2082-2, Aerospace series - Aluminium alloy forging stock and forgings - Technical specification - Part 2 - Forging stock EN2082-3, Aerospace series - Aluminium alloy forging stock and forgings - Technical specification - Part 3 - Pre-production and production forgings. Copyright Asso

12、ciation Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,- AECMA PREN2082-01 8b 1012311 0007675 2 W prEN2082-1 Page 4 Def i ni ti ons 4.1 Manufacturer Company producing the f

13、orging stock or the forgings in the form and condition which it is supplied to the purchaser. 42 Purchaser Company which orders and purchases the-forgings or the forging stock. 4.3 Cast n 4.3.1 Metal taken from the same melt in a furnace or crucible or from several melts mixed in the same furnace or

14、 crucible before pouring. 4.3.2 metal taken from the furnace before the next following charge. Where a continuous melting process is used, a cast may be defined as 4.4 Batch A batch consists of forging stock or forgings : - Of the same form and nominal dimensions or having the same drawing number an

15、d - From the same cast and - In the same heat treatment condition and - From the same heat treatment charge for an air furnace or from the same heat treatment run for a salt bath furnace. The heat treatment charge and run for a salt bath furnace shall be defined in the manufacturing schedule. . 4.5

16、Pre-production forgings Forgings produced to a particular design which qualify the method ofmanufacture and equipment configuration and which demonstrate that the requirements of the purchaser can be met. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under

17、 license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2082-O1 6 1012311 0007676 4 * O a a prEN2082-1 Page 5 4.6 Inspection schedule Se.e .EN2078. 4.7 Manufacturng schedule See EN2078. 4.8 Inspection and testing report See EN2078. 4.9 “Capabi

18、lity clause“ Reference to capability signifies that sufficient evidence of a statistical nature with respect.to the properties under consideration can be submitted io show that the requirements of the relevant standard will be met on the basis of a reduced amount of testing. Such action in no way re

19、duces the obligations of the manufacturer to fulfil all requirements, If subsequent testing indicates that a product does not comply with the requirements the batch shall be rejected. 5 Manufacture 5.1 Forgings shall be made- from forging stock compTying with the relevant EN material standard and EN

20、2082-2. . 5.2 Unless otherwise specified, thre method of manufacture to be employed shall be at the discretion of the manufacturer. 5.3 Conformance with the requirements of the purchaser shall be demonstrated by the manufacture and inspection and testing of pre-production forgings as required by EN2

21、082-3. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN20Z-OL 6 LOL23LL 0007677 6 prEW082-I Page 6 5.4 The prohcrcts shall be supplied in he

22、 heat treatmen, condition specif,zd in the material standard. If otherwise agreed, or if there are more than one heat treatment condition in the material standard, the condition of supply shall be specified on the order or on the drawing. If a specific heat treatment temperature (value and tolerance

23、) is stated, that temperature shall be mandato.ry. If a heat treatment temperature range is stated, a temperature w reduced by the furnace tolerances shall be selected. Unless otherwise specified, the charge shall be maintained at subject to the tolerance of - + 5”C, for the period stated. thin that

24、 range the temperature 6 Traceability Each product shall be identifiable to its cast and batch at all stages of manufacture and delivery. 7 Freedom from defects The products shall be free from harmful defects and notwithstanding previous acceptance of products complying with this standard; any produ

25、ct that is found, at a later stage, to contain such defects may be rejected. 8 Testing The tests required by the “material standard, the order, the inspection schedule or the drawing shall be made in accordance with the requirements of the appropriate test standard. If a test standard does not exist

26、, the method shall be agreed between the manufacturer and the purchaser. The frequency of testing shall be as specified in EN2082-2 or EN2082-3,unless otherwise specified on the drawing, order, or inspection schedule. 8.1 Chemical composition 8.1.1 The chemical composition of the delivered product s

27、hall comply with the requirements of the relevant material standard. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2082-OL b L0123LL 00076

28、78 E . 8. .2 The chem,ial compos prEN2082-1 Page 7 tion of each cast shall be determined. The samples taken for analysis purposes shall be representative of the cast. The method of analysis shall be selected by the manufacturer, but in case of dispute, the method set out in the relevant IS0 standard

29、 shall be used. If no .IS0 standard exists a fundamental method of chemical analysis shall be used. 8.2 8.2.1 Test samples for the tests required by the material standard shall be obtained bv one or more of the following methods as agreed between the Preparation of test samples and test pieces manuf

30、acturr and the purchaser and indicated on schedule : a) b) Test samples cut from forgings, Test samples forged integrally with the forg the drawing or the inspection c) Test samples forged separately from the same batch of forging stock as the forgings they represent. 8.2.2 The test samples and test

31、 pieces shall be marked in such a manner that their identity and orientation with respect to the product and the batch is maintained. 8.2.3 Test samples removed from finished forgings shall not be further worked. The preparation of test samples for the release of forging stock shall be carried out i

32、n accordance with EN2082-2. 8.2.4 ShouTd the test samples be taken as described in clause 8.2.1 a), the purchaser shall specify the number of forgings to be cut up and shall define in the drawing or inspection schedule the location from which the test samples are to be taken. 8.2.5 Dimensions of tes

33、t samples and test pieces representing forgings to be agreed between manufacturer and purchaser and shall be stated on draw order or inspection schedule. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction o

34、r networking permitted without license from IHS-,-,-: AECMA PREN2082-OL b H 10L23Ll 0007b79 T II prEN2082-1 Page 8 8.3 Heat treatment of test samples 8.3.1 condition shall be heat treated with the batch of .forgings they represent. Test samples representing forgings to be supplied in any heat treate

35、d .Unless otherwise agreed between manufacturer and purchaser samples shall not be cut from forgings before heat treatment. 8.3.2 Test samples cut from forgings in the finally heat treated condition shall not be further heat treated. 8.3.3 For forgings supplied in other than the finally heat treated

36、 condition the test samples required for proving the characteristics of this condition shall be re-heat treated in accordance with the requirements of the materials standard. 8.4 Re-tests If any inspection or test fails to meet the. requirements, re-tests shall be carried out as follows : 8.4.1 Tens

37、ile tests If the test procedure or the test piece preparation is faulty, testing shall be re-appl ied at the original frequency after identification of the original cause of fai 1 Ure. When failure cannot be attributed to a faulty test procedure or to test piece Preparation, additional identical tes

38、t samples shall be. selected at twice the original frequency. At least one of the re-tests shall be from the products or forgings on which the incorrect result was obtained (unless already rejected by the manufacturer after suitable identification of the cause of the failure). If all re-test results

39、 are satisfactory, the batch shall be accepted. If one or more re-test results are unsatisfactory, the batch shall be either : - rejected, or - re-heat treated and tested as a completely new batch. -3 - Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under l

40、icense with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2082-01 b 1012311 0007b80 b prEN2082-1 Page 9 c- 8.4.2 Other tests For other tests specific to a product the re-test procedure shall be as defined in the order, drawing, or inspection sched

41、ule. 8.5 Re-heat treatment No product or test sample shall be re-solution-heat treated more than once without the agreement of the purchaser. 9 Marking Products shall be marked in accordance with EN2082-2 for forging stock and EN2082-3 for forgings. 10 Acceptance If required by the order, the manufa

42、cturer shall inform the purchaser or his chosen agent of the planned dates for the extraction of samples and acceptance testing, in order that these operations may be witnessed. 11 Inspection and testing report The supplier shall furnish with each delivery of forging stock, pre-production and produc

43、tion forgings a form of certificate conforming to requirements Of EN2078 stating the following : - Manufacturers name and address, - Contract and/or order number, - Material standard number, - Description of supplies, including drawing number, - Quantity, - Cast and batch numbers, - Delivery conditi

44、on, . Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-:AECMA PREN2082-01 86 = 1012311 0007b81 8 prEN2082-1 Page 10 Batch and/or test samples heat trea

45、tment, if appropriate, Inspectors stamp, Results of the mandatory tests, re-tests and chemjcal analys s, carried out , A certification clause signed for and on behalf of the manufacturer. Packing If the purchaser does not specify any particular requirements, the manufacturer shall apply suitable pro

46、tective treatment to ensure that the products are information : delivered in a satisfactory condition. The exterior of the packing shall bear the following .- Name of purchaser, - Weight , - Order number and sufficient information to enab documentation. related to the relevant 13 Wording of orders T

47、he orders shall clearly ind cate : - Quantities to be supplied, - Dates of delivery, - Material standard number, - Delivery condition, e the contents to be - Dimensions and tolerances of products, or drawing number defining the forging, with the applicable issue number, address , - Forwarding - Manufactur - Nature and ng and inspection schedule references, type of packing, if required. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-