BS PD CEN TS 12201-7-2014 Plastics piping systems for water supply and for drainage and sewerage under pressure Polyethylene (PE) Guidance for the assessment of conformity.pdf

《BS PD CEN TS 12201-7-2014 Plastics piping systems for water supply and for drainage and sewerage under pressure Polyethylene (PE) Guidance for the assessment of conformity.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TS 12201-7-2014 Plastics piping systems for water supply and for drainage and sewerage under pressure Polyethylene (PE) Guidance for the assessment of conformity.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 7: Guidance for the assessment of conformity PD CEN/TS 12201-7:2014National foreword This Published Document is the UK implementation of CEN/TS 12201-7:2014. It sup

2、ersedes DD CEN/TS 12201-7:2003 and DD CEN/ TS 13244-7:2003, which are withdrawn. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastics piping for pressure applications. A list of organizations represented on t

3、his committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 83045

4、7 ICS 23.040.01; 91.140.60 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 March 2014. Amendments/corrigenda issued since publication Date Text affected PU

5、BLISHED DOCUMENT PD CEN/TS 12201-7:2014 TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 12201-7 February 2014 ICS 91.140.60; 23.040.01 Supersedes CEN/TS 12201-7:2003, CEN/TS 13244- 7:2003 English Version Plastics piping systems for water supply, and for drainage and se

6、werage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity Systmes de canalisations en plastique pour lalimentation en eau et pour les branchements et les collecteurs dassainissement avec pression - Polythylne (PE) - Partie 7: Guide pour lvaluation de la conformit

7、Kunststoff-Rohrleitungssysteme fr die Wasserversorgung und fr Entwsserungs- und Abwasserdruckleitungen - Polyethylen (PE) - Teil 7: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 19 August 2013 for provisional application. The period of va

8、lidity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in th

9、e same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN me

10、mbers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Port

11、ugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any f

12、orm and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 12201-7:2014 E PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 Abbreviated terms 10 5 General . 11 6 Testing and

13、inspection . 11 6.1 Grouping 11 6.1.1 General . 11 6.1.2 Size groups 11 6.1.3 Fitting groups 11 6.1.4 Fitting types . 12 6.2 Type testing . 12 6.3 Batch release tests . 21 6.4 Process verification tests 24 6.5 Audit tests . 27 6.6 Indirect tests 30 6.7 One-off products and products produced in very

14、low quantity 30 6.8 Mechanical fittings 30 6.9 Documentation 31 6.9.1 Type test results . 31 6.9.2 Test records 31 6.9.3 Technical file for certification purposes 31 A.1 General . 32 A.2 Change . 32 A.2.1 Change of base polymer 32 A.2.2 Change of grade 32 A.2.3 Change of pigment . 32 A.2.4 Change of

15、 additives other than pigments 32 A.3 Type testing required for re-evaluation 33 A.3.1 Changes A.2.1 and A.2.3.1 . 33 A.3.2 Changes A.2.2.1, A.2.2.2, A.2.2.3, A.2.3.2, A.2.4.1, A.2.4.2 and A.2.4.3 33 B.1 Grouping 34 B.2 Type tests 34 B.3 Batch release tests . 36 B.4 Process verification tests 36 B.5

16、 Audit tests . 36 Bibliography . 40 PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 3 Foreword This document (CEN/TS 12201-7:2014) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possi

17、bility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 12201-7:2003 and CEN/TS 13244-7:2003. EN 12201, Plastics piping systems for water sup

18、ply, and for drainage and sewerage under pressure Polyethylene (PE), consists of the following parts: EN 12201-1, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 1: General EN 12201-2, Plastics piping systems for water supply, and for dra

19、inage and sewerage under pressure Polyethylene (PE) Part 2: Pipes EN 12201-3, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 3: Fittings EN 12201-4, Plastics piping systems for water supply, and for drainage and sewerage under pressure P

20、olyethylene (PE) Part 4: Valves EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 5: Fitness for purpose of the system CEN/TS 12201-7, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyet

21、hylene (PE) Part 7: Guidance for the assessment of conformity This issue of CEN/TS 12201-7 takes into account the technical changes made in the revision of EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-5 and EN 12201-4, published in 2011 and respectively in 2012. Guidance for the assessment of confor

22、mity given in this document has been revised to reflect the changes made to test methods and requirements given in EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-4 and EN 12201-5. Two new types of pipe have been introduced, i.e. coextruded pipes and peelable layer pipes. The sampling procedures and sa

23、mpling frequencies for these types of pipes have been introduced into the tables for TT, BRT, PVT and AT for pipes. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium,

24、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan

25、d, Turkey and the United Kingdom. PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 4 Introduction Figure 1 and Figure 2 are intended to provide general information on the concept of testing and organization of those tests used for the purpose of the assessment of conformity. For each type of test, i.e.

26、 type testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this part of EN 12201 details the applicable characteristics to be assessed as well as the frequency and sampling of testing. A typical scheme for the assessment of conformity of compounds, pipes, fit

27、tings, valves, joints or assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of compounds, pipes, fittings, valves, joints or assemblies by manufacturers, including certificatio

28、n, is given in Figure 2. PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 5 Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 6 1 Scope This part of EN 12201 gives guidance for the assessment of conformity o

29、f compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management s

30、ystem conforms to or is no less stringent than the relevant requirements to EN ISO 9001 1. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065 5, EN ISO/IEC 17021 3 or EN ISO/IEC 17020 2, as applicable. In conjunction with Parts 1

31、to 5 of EN 12201 (see Foreword) this document is applicable to polyethylene (PE) plastics piping systems for water supply, and for drainage and sewerage under pressure. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be us

32、ed under the following conditions: a) allowable operating pressure, PFA, up to 25 bar 1) ; b) an operating temperature of 20 C as a reference temperature; c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 2 For applications ope

33、rating at constant temperature greater than 20 C and up to 40 C, see EN 12201-1:2011, Annex A. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or

34、regulations and installation practices or codes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an

35、y amendments) applies. EN 12201-1:2011, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General EN 12201-2:2011+A1:2013, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - P

36、art 2: Pipes EN 12201-3:2011+A1:2012, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings 1) 1 bar = 0,1 MPa = 10 5Pa; 1 MPa = 1 N/mm 2PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 7 EN 12201-4:2012, Plastics piping systems fo

37、r water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves EN 12201-5:2011, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system EN ISO 6259-1, Thermoplastics pipe

38、s - Determination of tensile properties - Part 1: General test method (ISO 6259-1) EN ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162) EN ISO 13477, Thermoplastics pipes for the conveyance of fluids

39、- Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477) EN ISO 13478, Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478) ISO 14236, Plastics

40、pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems ISO 17885, Plastics piping systems - Mechanical fittings for pressure piping systems - Specifications 2)ISO 21751, Plastics pipes and fittings - Decohesion test of electrofusio

41、n assemblies - Strip-bend test 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12201-1:2011, EN 12201-2:2011+A1:2013, EN 12201-3:2011+A1:2012, EN 12201-4:2012 and EN 12201-5:2011 and the following apply. 3.1 certification body impartial body, governme

42、ntal or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 5. 3.2 inspection body body that performs

43、 inspection Note 1 to entry: A body can be an organization or part of an organization. Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 2. 3.3 testing laboratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performan

44、ce of materials and products Note 1 to entry: In the context of this part of EN 12201, the materials and products can be subjected to type testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable. 2) At the time of publication of this Technical

45、Specification, this document is still in development and can be found under ISO/DIS 17885. PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 8 Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 4. 3.4 quality management system management system to direct and control an o

46、rganization with regard to quality Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 1. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type test T

47、T test performed to prove that the material, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verificatio

48、n tests are done regularly. 3.7 batch release test BRT test performed by or on behalf of the manufacturer on a batch of compound or products, which is satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on com

49、pound or products or joints or assemblies at specific intervals to confirm that type tests originally performed on the compound or products or joints or assemblies continue to be valid and the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of compound or products and are carried out as a measure of process control. 3.9 audit test AT test performed by a test laboratory