BS ISO IEC 7812-1-2017 Identification cards Identification of issuers Numbering system《识别卡 发行者识别 数字标识系统》.pdf

《BS ISO IEC 7812-1-2017 Identification cards Identification of issuers Numbering system《识别卡 发行者识别 数字标识系统》.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 7812-1-2017 Identification cards Identification of issuers Numbering system《识别卡 发行者识别 数字标识系统》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO/IEC 7812-1:2017 Identification cards Identification of issuers Part 1: Numbering system BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO/IEC 7812-1:2017 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 7812-1:

2、2017. It supersedes BS ISO/IEC 7812-1:2015 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication d

3、oes not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017 ISBN 978 0 580 92934 2 ICS 35.240.15 Compliance with a British Standard cannot confer immunity fro

4、m legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO/IEC 7812-1:2017 Identification cards Identification of issuers Part 1: Num

5、bering system Cartes didentification Identification des metteurs Partie 1: Systme de numrotation INTERNATIONAL STANDARD ISO/IEC 7812-1 Reference number ISO/IEC 7812-1:2017(E) Fifth edition2017-01 ISO/IEC 2017 BS ISO/IEC 7812-1:2017ii ISO/IEC 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/

6、IEC 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written perm

7、ission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 7812-1:20

8、17(E)BS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E)Foreword iv Introduction v 1 Scope .1 2 Normative references 1 3 Terms and definitions .1 4 Numbering system 2 4.1 PAN format . 2 4.2 IIN . 3 4.2.1 IINs beginning with “00” . 3 4.2.2 IINs beginning with “80” . 3 4.2.3 IINs beginning with “89” . 3 4.2.

9、4 IINs beginning with “9” 3 4.3 Individual account number 4 4.4 Check digit. 4 Annex A (informative) National numbering systems for card issuers 5 Annex B (normative) Luhn formula for computing modulus-10 “double-add-double” check digits 6 Bibliography 7 ISO/IEC 2017 All rights reserved iii Contents

10、 PageBS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E) Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the dev

11、elopment of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governm

12、ental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Di

13、rectives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some

14、 of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent

15、declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as inform

16、ation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/IEC JTC 1, Information technology, SC 17, Cards and personal identification. T

17、his fifth edition cancels and replaces the fourth edition (ISO/IEC 7812-1:2015), which has been technically revised. Key changes made in this edition: Clause 3: added definitions for “acquirer” and “card acceptor”; Clause 3: removed the definition of “major industry identifier”; Clause 3: removed de

18、finition of “registration management group” to ISO/IEC 7812-2; Removed previous outline of major industry identifier descriptions; Clause 4: revised the length of an IIN to 8 digits (from 6 digits); Clause 4: revised the minimum length of a PAN to 10 digits (from 8 digits); Annex A: modified A.2 to

19、be the role of the registration authority (from previously being defined as role of registration management group); Annex B: revised the example to reflect an 8 digit IIN. A list of all the parts in the ISO 7812- series, can be found on the ISO website.iv ISO/IEC 2017 All rights reservedBS ISO/IEC 7

20、812-1:2017ISO/IEC 7812-1:2017(E) Introduction This document is one of a series of International Standards specifying: a numbering system for the identification of card issuers operating within an interchange environment, the format of the issuer identification number and the primary account number;

21、application and registration procedures for card issuers who operate a card program in an international interchange environment. Card issuers not operating in an international interchange environment are encouraged to contact their sponsoring authorities for a number assigned by that national standa

22、rds body, or the Registration Authority (RA) if no Sponsoring Authority (SA) exists. Use of a national IIN will avoid conflicts if the cards are used in an international interchange environment. ISO/IEC 2017 All rights reserved vBS ISO/IEC 7812-1:2017BS ISO/IEC 7812-1:2017Identification cards Identi

23、fication of issuers Part 1: Numbering system 1 Scope This document specifies a numbering system for the identification of the card issuers, the format of the issuer identification number (IIN) and the primary account number (PAN). 2 Normative references The following documents are referred to in the

24、 text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3166-1, Codes for the representation of

25、 names of countries and their subdivisions Part 1: Country codes ISO/IEC 7812-2, Identification cards Identification of issuers Part 2: Application and registration procedures ISO 8583-1, Financial transaction card originated messages Interchange message specifications Part 1: Messages, data element

26、s and code values ITU-T Recommendation E. 118,The international telecommunication charge card 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC

27、 Electropedia: available at http:/ /www.electropedia.org/ ISO Online browsing platform: available at http:/ /www.iso.org/obp 3.1 acquirer institution (or its agent) which acquires from the card acceptor the data relating to the transaction and initiates the data into an interchange system 3.2 card f

28、orm factor (physical or virtual) provided by a card issuer Note 1 to entry: For this document, this definition is not limited to ISO/IEC 7810 ID-1 card. Some examples of other card types include but are not limited to virtual, thin flexible, single-use, integrated-circuit or mobile devices. 3.3 card

29、 acceptor party accepting the card for the purpose of presenting transaction data to an acquirer or intermediary facilitating the transaction flow INTERNATIONAL ST ANDARD ISO/IEC 7812-1:2017(E) ISO/IEC 2017 All rights reserved 1BS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E) 3.4 cardholder customer ass

30、ociated with the primary account number 3.5 card issuer institution (or its agent) that issues the card to the cardholder Note 1 to entry: For institutions in the financial services industry and regulatory community, a legal entity as defined in ISO 17442, or its agent, that issues the card to the c

31、ardholder 3.6 individual account number number assigned by the card issuer for the purpose of identifying an individual account 3.7 interchange exchange of transaction data between two or more participants 3.8 issuer identification number IIN number that identifies the card issuer and that forms the

32、 first part of the primary account number 3.9 primary account number PAN number consisting of a maximum of 19 digits that identifies the card issuer and the cardholder Note 1 to entry: See 4.1 and Figure 1. 3.10 registration authority RA organization appointed by the ISO Council, responsible for ass

33、igning IINs and maintaining the ISO Register of Card Issuer Identification Numbers 4 Numbering system 4.1 PAN format The PAN of a card (see 3.9) is made up of three main components: a) the IIN, 8 numeric digits in length (see 4.2); b) the individual account number (see 4.3); and c) a check digit (se

34、e 4.4). See Figure 1 for number format. NOTE For national numbering systems, refer to Annex A.2 ISO/IEC 2017 All rights reservedBS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E) Figure 1 Composition of the Primary Account Number 4.2 IIN All IINs issued in accordance with this document shall be applied fo

35、r and registered as specified in ISO/IEC 7812-2. Applicants whose applications fulfil the criteria for approval specified in ISO/IEC 7812-2 will be assigned an IIN or, in the case of a block assignment, a block of IINs. 4.2.1 IINs beginning with “00” IINs in the range “00” have been allocated for as

36、signment to institutions other than card issuers in order to accommodate requirements in ISO 8583-1. Applicants applying for IINs commencing with “00” shall refer to ISO 8583-1, where application procedures and an application form are provided. 4.2.2 IINs beginning with “80” IINs beginning with “80”

37、 are for use by healthcare institutions. These IINs are managed by individual national registration authorities. Each national registration authority shall register with the RA so that they can be identified in the ISO Register of Card Issuer Identification Numbers. The format of the entry for the n

38、ational registration authorities shall be “80CCC”, where “80” denotes healthcare and “CCC” is the three-digit numeric country code, as specified in ISO 3166-1. The formatting and coding of the digits following “80CCC” is at the discretion of the regional healthcare authorities. Enquiries for details

39、 of national healthcare registration authorities may be made to the RA. See http:/ /www.iso. org/iso/maintenance_agencies 4.2.3 IINs beginning with “89” IINs beginning with “89” are for use by telecommunications administrations and recognized private operating agencies in accordance with ITU-T/Rec.

40、E.118. These IINs are maintained by the International Telecommunication Union, and applicants applying for IINs for use on telecommunications cards shall apply for an IIN commencing with “89”. Enquiries for IINs starting with “89” shall be made to: International Telecommunication Union, Place des Na

41、tions, 1211 Geneva 20, Switzerland, Telephone: +41 227 305 211, Fax: + 41 227 337 256. http:/ /www.itu.int/en/Pages/default.aspx 4.2.4 IINs beginning with “9” IINs beginning with “9” are reserved for use by national standards bodies, where they exist, or by the RA in the absence of a national standa

42、rds body. The format of the entry for the national standards bodies shall be “9CCC”, where “9” denotes national use and “CCC” is the three-digit numeric country code, as specified in ISO 3166-1. ISO/IEC 2017 All rights reserved 3BS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E) In the interest of interna

43、tional conformity, national standards bodies are advised to assign IINs in accordance with the recommendations given in Annex A. The RA will oversee the assignment of any 9 series IINs in any country where a national standards body does not exist, or has not implemented an IIN management function. A

44、ny 9 series IIN assigned by the RA is 9 digits in length, and will conform to the structure of 9 followed by the three-digit numeric country code, as specified in ISO 3166-1. 4.3 Individual account number The individual account number (see Figure 1) shall be assigned by the card issuer. It immediate

45、ly follows the IIN and is variable in length with a minimum of 1 and maximum of 10 digits. 4.4 Check digit The individual account number (see 4.3) shall be followed by a check digit. This digit shall be calculated on all the preceding digits of the PAN (see Figure 1) and shall be computed according

46、to the Luhn formula for modulus-10 check digit (see Annex B).4 ISO/IEC 2017 All rights reservedBS ISO/IEC 7812-1:2017ISO/IEC 7812-1:2017(E) Annex A (informative) National numbering systems for card issuers A.1 Introduction IINs beginning with 9 have been assigned for use by national standards bodies

47、 in order to establish numbering systems for card issuers. If no national numbering system exists, or if the national standards body is unable to establish a national numbering system, applicants for IINs in that country may apply through the RA. NOTE ISO maintains a listing on national numbering re

48、gistries, refer to www.iso.org A.2 Contact with the Registration Authority (RA) The RA acting on behalf of ISO/IEC JTC 1/SC 17 shall, on request, provide advice and counsel to any national standards body on the establishment and operation of a national numbering system. National standards bodies tha

49、t intend to set up national numbering systems are asked to supply the RA with details of the national procedures for the assignment of IINs, the method used to identify card issuers, and the name of the organization administering the system. A.3 Operation of national numbering systems National standards bodies are advised to establish rules by means of national standards or other methods for identifying card issuers and individual cardholders (See 4.2.4)