BS ISO 9162-2013 Petroleum products Fuels (class F) Liquefied petroleum gases Specifications《石油产品 燃料(F类) 液化石油气 规格》.pdf

《BS ISO 9162-2013 Petroleum products Fuels (class F) Liquefied petroleum gases Specifications《石油产品 燃料(F类) 液化石油气 规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9162-2013 Petroleum products Fuels (class F) Liquefied petroleum gases Specifications《石油产品 燃料(F类) 液化石油气 规格》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 9162:2013 Petroleum products Fuels (class F) Liquefied petroleum gases SpecificationsBS ISO 9162:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9162:2013. The UK participation in its preparation was entrusted to Technica

2、l Committee PTI/15, Natural Gas and Gas Analysis. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British

3、 Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 78540 5 ICS 75.160.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 Aug

4、ust 2013. Amendments issued since publication Date Text affectedBS ISO 9162:2013 ISO 2013 Petroleum products Fuels (class F) Liquefied petroleum gases Specifications Produits ptroliers Combustibles (classe F) Gaz de ptrole liqufis Spcifications INTERNATIONAL STANDARD ISO 9162 Second edition 2013-07-

5、15 Reference number ISO 9162:2013(E)BS ISO 9162:2013ISO 9162:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or me

6、chanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749

7、 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 9162:2013ISO 9162:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Requirements 2 3.1 General . 2 3.2 Water content . 2 4 Precision and interpr

8、etation of test results . 3 5 Documentation . 3 6 Sampling 3 Annex A (informative) Evaporation residue of liquefied petroleum gases 4BS ISO 9162:2013ISO 9162:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b

9、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a

10、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are

11、described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives. Attention is drawn t

12、o the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the

13、ISO list of patent declarations received. www.iso.org/patents. Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 28, Petroleum products and lubricants, Subcommittee SC 4

14、, Classifications and specifications, WG 5, Gas turbine fuels. This second edition cancels and replaces the first edition (ISO 9162:1989), of which it constitutes a minor revision with the following changes: ISO 4260 (Wickbold sulphur determination method) has been replaced by ASTM D6667 (method for

15、 determination of total volatile sulphur); new methods for evaporation residue in liquefied petroleum gas (LPG) have been added: EN 15470, EN 15471, and EN 16423.iv ISO 2013 All rights reservedBS ISO 9162:2013INTERNATIONAL ST ANDARD ISO 9162:2013(E) Petroleum products Fuels (class F) Liquefied petro

16、leum gases Specifications HEALTH AND SAFETY WARNING The use of this International Standard involves potentially hazardous materials, operations, and equipment. This International Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the

17、user to consult the relevant safety and health regulations, determine the applicability of regulatory limitations, and establish appropriate safety and health practices prior to use. 1 Scope This International Standard specifies required characteristics and additional information to be supplied to t

18、he purchaser by the vendor of those products commonly referred to as liquefied petroleum gases (see ISO 8216-3) and is intended to apply to international transfers of commercial propane and commercial butane. This International Standard is neither intended nor expected to replace or encroach upon na

19、tional standards of any country, since each country is subject to different regulations, codes, industry practices and market utilization. NOTE National standards and safety codes might be applicable when formulating any characteristics required for specific uses. 2 Normative references The followin

20、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3993, Liquefied

21、 petroleum gas and light hydrocarbons Determination of density or relative density Pressure hydrometer method ISO 4256, Liquefied petroleum gases Determination of gauge vapour pressure LPG method ISO 4257, Liquefied petroleum gases Method of sampling ISO 4259, Petroleum products Determination and ap

22、plication of precision data in relation to methods of test ISO 6251, Liquefied petroleum gases Corrosiveness to copper Copper strip test ISO 7941, Commercial propane and butane Analysis by gas chromatography ISO 8216-3, Petroleum products Fuels (class F) Classification Part 3: Family L (Liquefied pe

23、troleum gases) ISO 8819, Liquefied petroleum gases Detection of hydrogen sulfide Lead acetate method ISO 8973, Liquefied petroleum gases Calculation method for density and vapour pressure EN 15470, Liquefied petroleum gases Determination of dissolved residues High temperature gas chromatographic met

24、hod EN 15471, Liquefied petroleum gases Determination of dissolved residues High temperature gravimetric method EN 16423, Liquefied petroleum gases Determination of dissolved residue Gas chromatographic method using liquid, on-column injection ISO 2013 All rights reserved 1BS ISO 9162:2013ISO 9162:2

25、013(E) ASTM D6667-04, Standard test method for determination of total volatile sulphur in gaseous hydrocarbons and liquefied petroleum gases by ultraviolet fluorescence 3 Requirements 3.1 General When determined in accordance with the methods given in Table 1, the properties of commercial butane and

26、 commercial propane shall be in accordance with the limiting requirements given in that table. NOTE Individual contractual agreements, national standards, national safety codes, and/or requirements of distribution systems may prescribe other limits. Table 1 Specifications for liquefied petroleum gas

27、es Character Unit Limit Commercial propane ISO-F-LP Commercial butane ISO-F-LB Test method reference Density at 15 C kg/m 3 Report Report ISO 3993 or ISO 8973 Gauge vapour pressure at 40 C kPa max 1550 a 520 a ISO 4256 bor ISO 8973 Volatility C 2hydrocarbonsC 4hydrocarbonsC 5hydrocarbons% (molar) %

28、(molar) % (molar)max maxReport c 7, 5 a 0,2 e- - 2,5 e ISO 7941 Unsaturated hydrocar- bons % (molar) Report d Report d ISO 7941 Dienes % (molar) max 0,5 e 0,5 e ISO 7941 Evaporation residue mg/kg max 60 60 EN 15470 gor EN 15471 gor EN 16423 Corrosiveness to copper max 1 1 ISO 6251 Sulphur mg/kg max

29、50 e 50 e ASTM D6667 Hydrogen sulphide Pass Pass ISO 8819 Free water content None f None f aCertain national standards and/or regulations may describe other limits. bIn case of dispute about the vapour pressure, ISO 4256 shall prevail. cPhysical limitations of transport and storage facilities shall

30、be considered for refrigerated transport; a common limit is 2 % (molar) maximum. dCertain national standards may prescribe a limitation on saturated hydrocarbons. eCertain national standards may prescribe other limits. fThe presence of water shall be determined by visual inspection. For shipments of

31、 refrigerated liquefied petroleum gases at their atmospheric boiling point, it is essential that the water content is below the saturation level at this temperature as determined by a method agreed between the buyer and the seller. gIn case of dispute about the evaporation residue, EN 15470 and EN 1

32、5471 shall prevail. 3.2 Water content Commercial butane and commercial propane shall not contain free or suspended water detectable by visual inspection.2 ISO 2013 All rights reservedBS ISO 9162:2013ISO 9162:2013(E) 4 Precision and interpretation of test results Most of the methods of test given in

33、Table 1 contain a statement of the precision, i.e. the repeatability and reproducibility, to be expected from them but, in cases of dispute, the procedure described in ISO 4259, which uses precision data in the interpretation of test results, shall be used. 5 Documentation The documentation supplied

34、 to the purchaser by the vendor shall include at least the following: a) a reference to this International Standard; b) the type of liquefied petroleum gas supplied, i.e. commercial propane or commercial butane; c) the brand name of the product; d) the ISO designation code, i.e. ISO-F-LP or ISO-F-LB

35、 (see ISO 8216-3); e) the suppliers production code and the date of production; f) precautionary and safety advice. If a transportable container is supplied with the liquefied petroleum gas, it shall also be clearly marked with this information. 6 Sampling A representative sample of non-refrigerated

36、 commercial butane or commercial propane shall be taken in accordance with the procedure given in ISO 4257. For refrigerated liquefied petroleum gases, a sampling procedure shall be agreed between the parties concerned. NOTE Proper sampling of the liquefied petroleum gases is extremely important if

37、the test results are to be significant. ISO 2013 All rights reserved 3BS ISO 9162:2013ISO 9162:2013(E) Annex A (informative) Evaporation residue of liquefied petroleum gases Liquefied petroleum gases may contain trace amounts of non-volatile residues. These contaminants can include a variety of hydr

38、ocarbons derived from the distillation process, compressor lubricating oils, valve greases, and rubber and elastomer extenders from hoses. In the majority of applications, the liquid is evaporated and the fuel is fed to the appliance in the gaseous phase. In those cases where the natural evaporation

39、 capacity of the storage tank is not sufficient to provide the required quantity of gas, vaporizers are widely used. In this case, excessive non-volatile residues can be very detrimental. A distinction can be made between industrial and automotive vaporizers and a variety of energy sources may be ap

40、plied. Automotive vaporizers use, in the majority of installations, the engine coolant as a heat source. With the engine fully warmed up, the coolant will have a temperature of about 80 C to 100 C. Taking this temperature into account as well as the more complicated construction of the automotive va

41、porizer/pressure regulator relative to the industrial installation, it can be concluded that the automotive equipment is the most sensitive with respect to the content of residual matter.4 ISO 2013 All rights reservedBS ISO 9162:2013BS ISO 9162:2013ISO 9162:2013(E) ISO 2013 All rights reserved ICS 7

42、5.160.30 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are publ

43、ished by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based soluti

44、ons. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with th

45、e knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and

46、international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are d

47、esigned to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed da

48、ily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Membe

49、rs. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supp