ISO 22555-2007 Ships and marine technology - Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf

《ISO 22555-2007 Ships and marine technology - Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf》由会员分享，可在线阅读，更多相关《ISO 22555-2007 Ships and marine technology - Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD ISO 22555 First edition 2007-09-15 Reference number ISO 22555:2007(E) ISO 2007 Ships and marine technology Propeller pitch indicators Navires et technologie maritime Indicateurs de pas du propulseurISO 22555:2007(E) ii ISO 2007 All rights reserved PDF disclaimer This PDF file

2、may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the re

3、sponsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-crea

4、tion parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.COPYRIGHT PROTECTED DOCUMENT ISO 200

5、7 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the coun

6、try of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandISO 22555:2007(E) ISO 2007 All rights reserved iii Contents Page 1 Scope 1 2 Normative references 1 3 Terms and de

7、finitions 1 4 Construction of indicator system 2 4.1 Indicator system 2 4.2 Transmitter . 2 4.3 Indicator . 2 5 Performance requirements . 3 5.1 General . 3 5.2 Calibration accuracy . 3 5.3 Damping efficiency . 3 5.4 Power supply fluctuation 3 5.5 Insulation resistance and high voltage . 3 6 Methods

8、 of testing and required test results 4 6.1 Construction 4 6.2 Environmental test 4 6.3 Calibration test 4 6.4 Damping test 4 6.5 Power supply fluctuation test 4 7 Interface 4 8 Marking . 4 9 Information . 4 Bibliography . 5ISO 22555:2007(E) iv ISO 2007 All rights reserved Foreword ISO (the Internat

9、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee

10、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand

11、ardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for

12、 voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all

13、 such patent rights. ISO 22555 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 6, Navigation.INTERNATIONAL STANDARD ISO 22555:2007(E) ISO 2007 All rights reserved 1 Ships and marine technology Propeller pitch indicators 1S c o p e This International Standar

14、d specifies the construction, performance requirements, methods of testing and required test results for the propeller pitch indicators (hereinafter referred to as “indicator system”) required by clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000). This International Standard is as

15、sociated with IMO Resolution A.694 (17) and IEC 60945. Where a requirement in this International Standard differs from IEC 60945, the requirement in this International Standard takes precedence. 2 Normative references The following referenced documents are indispensable for the application of this d

16、ocument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60945, Maritime navigational and radiocommunication equipment and systems General requirements Methods of testing and required

17、test results IEC 61162-1, Maritime navigation and radiocommunication equipment and systems Digital interfaces Part 1: Single talker and multiple listeners IEC 61162-2, Maritime navigation and radiocommunication equipment and systems Digital interfaces Part 2: Single talker and multiple listeners, hi

18、gh-speed transmission 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 propeller pitch indicator remote device capable of indicating the angular position of moving propeller blades between their maximum angular setting on either side of their

19、neutral position on the equipment to which they are mounted 3.2 indicator means by which the state of the equipment or machinery is represented to an observer NOTE An indicator shows both the sense and magnitude of the information it presents. An indicator can be analog or digital. 3.3 analog type i

20、ndicator indicator that shows the pitch angle in a continuous way, such as by means of an arrow pointer and graduated scaleISO 22555:2007(E) 2 ISO 2007 All rights reserved 3.4 digital type indicator indicator that shows the pitch angle in a discrete, alphanumeric way 3.5 calibration accuracy differe

21、nce between the angle registered by the transmitter and the angle indicated by an indicator 3.6 damping efficiency time elapsed for the indicated angle to match the angle of the transmitter shaft 4 Construction of indicator system 4.1 Indicator system 4.1.1 An indicator system should show informatio

22、n on the state of the equipment or machinery to which it is connected at locations adjacent to or remote from the equipment or machinery. At the equipment or machinery, such systems will generally comprise a sensor and transmitter; at the observers location, such systems will generally contain an in

23、dicator. In general, the system construction shall comply with the following requirements. 4.1.2 The indicator system enclosures shall be robust and constructed so as to facilitate easy adjustment and maintenance. 4.1.3 The indicator system shall be provided with an earthing terminal or shall be so

24、constructed as to be capable of being connected to an electrical earth. 4.1.4 An analog type indicator can be used as indicator(s) of the indicator system. It may be additionally provided by a digital type if fitted. 4.2 Transmitter The transmitter shall be driven by suitable means from the controll

25、able pitch propeller activating mechanism. 4.3 Indicator 4.3.1 An analog indicator shall be of a centre-zero type (preferably circular). Where a circular scale indicator is used, the zero position shall be uppermost. The direction “Ahead” or “Starboard” shall be to the right of the zero graduation;

26、the directions “Astern” or “Port” shall be to the left of the zero graduation. 4.3.2 The digital indicator shall indicate the pitch angle as readily legible digital figures preceded by a symbol or letter(s) indicating direction. The directions “Ahead” or “Starboard” shall be identified by the “plus”

27、 sign or by the letters “AH (ST)”, while “Astern” or “Port” shall be identified by a “minus” sign or by the letters “AS (PT)”. 4.3.3 The maximum angle indicated shall be the same for both Ahead/Starboard and Astern/Port and shall be no less than . 4.3.4 Scale graduations shall be no smaller than . G

28、raduation marks corresponding to increments shall be more prominent than those for intervening increments. 4.3.5 The pointer of an indicator shall be capable of being adjusted to zero. 40 1 5 ISO 22555:2007(E) ISO 2007 All rights reserved 3 4.3.6 The letters and graduations on the dial shall be such

29、 that the direction of ahead and astern can be clearly distinguished. 4.3.7 All illumination and lighting of an indicator shall be adjustable down to zero, except the control of the dimmers which shall remain readable. 4.3.8 The illumination and lighting of an indicator shall be arranged in order no

30、t to hinder an operators vision at night and in order to make the scale, pointer and letters as equally visible as possible, even in dim light or the dark. 5 Performance requirements 5.1 General The transmitter shall have the capacity to satisfy the requirements specified in 5.2, 5.3 and 5.4 when al

31、l connected indicators are operating simultaneously. The manufacturer shall clearly state the maximum number of indicator(s) or the capacity of connected indicator(s) that can be supported by a transmitter. 5.2 Calibration accuracy To calibrate the indicator system, the shaft of a transmitter is gra

32、dually rotated from the zero position to the maximum angle ahead (Starboard) or astern (Port), and the angles shown by an indicator are recorded everyof rotation. The difference between the angle of the transmitter shaft and the corresponding value shown at an indicator shall be within of the sum of

33、 the maximum angle in both directions. 5.3 Damping efficiency If a voltage is suddenly applied while the transmitter shaft is approximately at half of full-scale position and the indicator pointer is set to the zero position, the pointer shall be reset to that position within or less. 5.4 Power supp

34、ly fluctuation 5.4.1 The performance specified in 5.1 and 5.2 shall be maintained when the system is subject to the power supply fluctuations. 5.4.2 After repeated makings and breakings, the designated performance shall be demonstrated without carrying out manual adjustments. 5.4.3 When the rated vo

35、ltage and frequency are subjected to the combinations of fluctuations, as given in Table 1, the designated performance shall be demonstrated. 5.5 Insulation resistance and high voltage When insulation resistance and high voltage tests are to be carried out, IEC 60092-504 may be applied. Table 1 Fluc

36、tuation rate of the rated voltage and frequency Settled condition Voltage fluctuation Fluctuating period: Frequency fluctuation Transient condition Voltage fluctuation Fluctuating period: Frequency fluctuation 5 1,5 % 5s 10 % 600 s 5% 20 % 3s 10 %ISO 22555:2007(E) 4 ISO 2007 All rights reserved 6 Me

37、thods of testing and required test results 6.1 Construction The construction of an indicator system shall comply with the requirements specified in Clause 4. 6.2 Environmental test Unless otherwise stated in this International Standard, all the tests shall be carried out according to the requirement

38、s of IEC 60945. The manufacturer shall determine which components of the indicator system will be protected or exposed, as defined in IEC 60945. 6.3 Calibration test The calibration test shall be carried out in accordance with 5.2 and shall satisfy the requirements specified therein. 6.4 Damping tes

39、t The damping test shall be carried out in accordance with 5.3 and shall satisfy the requirements specified therein. 6.5 Power supply fluctuation test The power supply fluctuation test shall be carried out in accordance with 5.4 and shall satisfy the requirements specified therein. 7I n t e r f a c

40、e When the indicator system provides interface facilities, they shall meet the requirements of the appropriate international marine interface standards IEC 61162-1 and IEC 61162-2. 8 Marking 8.1 Each unit of an indicator system shall be marked with the following: identification of the manufacturer;

41、equipment type number or model identification number under which it was type tested; serial number of the unit. 8.2 Each unit shall be marked with the minimum safe distance from a magnetic compass at which it may be mounted (for bridge installation). The safe distance shall be measured in accordance

42、 with IEC 60945. 9 Information The manufacturer shall provide adequate equipment documentation to enable competent members of a ships crew to operate and maintain the equipment efficiently.ISO 22555:2007(E) ISO 2007 All rights reserved 5 Bibliography 1 ISO 8468, Ships and marine technology Ships bri

43、dge layout and associated equipment Requirements and guidelines 2 IEC 60092-504, Electrical installations in ships Part504: Special features Control and instrumentation 3 International Convention for the Safety of Life at Sea (SOLAS), 1974 (amended) 4 IMO Resolution A.694 (17), General requirements for shipborne radio equipment forming part of the global maritime distress and safety system (GMDSS) and for electronic navigational aidsISO 22555:2007(E) ICS 47.020.70 Price based on 5 pages ISO 2007 All rights reserved