IEEE C37 21-2017 en Control Switchboards.pdf

《IEEE C37 21-2017 en Control Switchboards.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 21-2017 en Control Switchboards.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Standard for Control Switchboards IEEE Std C37.21-2017 (Revision of IEEE Std C37.21-2005) IEEE Power and Energy Society Sponsored by the Switchgear Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C37.21-2017 (Revision of IEEE Std C37.21-2005) IEEE Standard for Control Switchboa

2、rds Sponsor Switchgear Committee of the IEEE Power and Energy Society Approved 23 March 2017 IEEE-SA Standards BoardAbstract: Ratings, construction, and testing of dead-front control switchboards containing, but not limited to, devices such as switches, control devices, instrumentation, metering, mo

3、nitoring, alarms, annunciators, protective and auxiliary relays, and regulating devices and accessories are covered in this standard. It includes, but is not specifically limited to, switchboards for the control and protection of apparatus used for or associated with power generation, conversion, tr

4、ansmis- sion, and distribution. Types of switchboards may include control, vertical, dead-front, enclosed, dual, or duplex switchboards. Other construction types include control desks, consoles, bench- boards, dual or duplex benchboards, fixed rack, cabinet, and swing rack cabinets. It does not appl

5、y to industrial controls, communication equipment, switchboards for use on board ships, or Class 1E switchboards for use in nuclear generating stations. Keywords: benchboard, console, control desk, control switchboard, dead-front switchboard, dual benchboard, duplex benchboard, enclosed switchboard,

6、 fixed rack cabinet, IEEE C37.21, swing rack cabinet, vertical switchboard The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2017 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 23 May 2017.

7、 Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and wo

8、rkmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related t

9、o the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEE

10、E is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment

11、 in the exercise of reasonable care in any given circumstances or, as appropri- ate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY , OR CONSEQUENTIAL D

12、AMAGES (INCLUDING, BUT NOT LIMITED TO: PROCURE- MENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY , WHETHER IN CON- TRACT, STRICT LIABILITY , OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT

13、OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard

14、 is translated, only the English version published by IEEE should be considered the approved IEEE standard.4 Copyright 2017 IEEE. All rights reserved. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be

15、 considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear

16、 that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does

17、 not provide consulting information or advice pertain- ing to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is imp

18、ortant that any responses to comments and questions also receive the concur- rence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordi- nating Committees are not able to provide an instant response to comments or questions except in those cases wher

19、e the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Through this joint effort over the many years, the switchge

20、ar assemblies standards have been of extreme value to the industry and further suggestions for improvement gained in the use of this standard will be welcomed. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 US

21、A Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory require- ments. Implementers of the standard are responsible for observing

22、 or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEE

23、E under US and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the pro- motion of engineering prac

24、tices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocop

25、y portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Ser- vice, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to

26、photocopy portions of 5 Copyright 2017 IEEE. All rights reserved. any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be supe

27、rseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corri- genda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then

28、in effect. Every IEEE standard is subjected to review at least every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users a

29、re cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ standards .i

30、eee .or g or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following

31、URL: http:/ standards .ieee .org/ findstds/ errata/ index .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this stan

32、dard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/

33、 standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unf

34、air discrim- ination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not re- sponsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the l

35、egal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determina

36、tion of the valid- ity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2017 IEEE. All rights reserved. Participants At the time this IEEE standard was complete

37、d, the SASCIEEE Standard for Control Switchboards Working Group had the following membership: Dan Hrncir, Chair Darryl Moser, Vice Chair Douglas J. Edwards Keith Flowers Lou Grahor Jose Jarque Michael Lafond Casey McCollum Jeffery Mizener Charles Morse Owen Parks Ahmad Qasem Richard Rohr Amy Rowell

38、Todd Sauve The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. William Ackerman Thomas Barnes Seth Benson William Bloethe Gustavo Brunello William Byrd Eldridge Byron Paul Cardinal Gary Donner Edgar Du

39、llni Douglas J. Edwards Dale Fredrickson Mietek Glinkowski Lou Grahor Randall Groves Thomas Hawkins Werner Hoelzl Dan Hrncir Richard Jackson Jose Jarque Yuri Khersonsky Boris Kogan Jim Kulchisky Chung-Yiu Lam William McBride John McClelland Venkatesh Minisandram Charles Morse Darryl Moser Jerry Murp

40、hy Dennis Neitzel Michael Newman Joe Nims T. W . Olsen Bansi Patel Iulian Profir Timothy Robirds Richard Rohr Thomas Rozek Ryandi Ryandi Todd Sauve Bartien Sayogo Robert Seitz Devki Sharma Xu She Jeremy Smith Jerry Smith Wayne Stec David Tepen James Van De Ligt John Vergis John Wang Kenneth White Ji

41、an Yu When the IEEE-SA Standards Board approved this standard on 23 March 2017, it had the following membership: Jean-Philippe Faure, Chair Gary Hoffman, Vice Chair John D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Tr

42、avis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Yu Yuan *Member Emeritus7 Copyright 2017 IEEE. All rights reserved. Introducti

43、on This introduction is not part of IEEE Std C37.212017, IEEE Standard for Control Switchboards. This standard has been revised to reflect changes that have been suggested since the 2005 revision of IEEE Std C37.21. The revisions in this standard include the following: Revised Switchgear Assemblies

44、Diagram, Figure a Moved “General Application Guide” and “Handling, Storage, and Installation Guide” from normative part of standard to an informative annex Aligned Usual Service Conditions with IEEE Std C37.20.1 B6 1 Revision of the rain test to use the test method in IEEE Std C37.100.1 2 Revision o

45、f the salt spray requirement for test of coatings from 200 h to 600 h, in line with revisions to other standards in the IEEE C37.20.X switchgear assemblies series of standards The following revisions reflect changes made in the 1985 edition: Modification of the use of units to conform to the latest

46、IEEE-SA policy on metrification Removal of current ratings for control switchboards Clarification of requirements for production tests Clarification of voltage and current limits for instruments and control circuits Clarification of voltage circuit protection Clarification of altitude correction fac

47、tors Expansion of nameplate requirements to include control switchboard ratings This standard includes only the requirements for control switchboards (also called control boards). These re- quirements were originally a part of IEEE Std C37.20-1969. Other types of equipment originally included in IEE

48、E Std C37.20-1969 are now incorporated in separate standards. IEEE Std C37.20-1969 for many years covered all switchgear assemblies including metal-enclosed bus and control switchboards. Standards committees of IEEE Switchgear Assemblies Subcommittee and NEMA Pow- er Switchgear Assemblies Technical

49、Committee recommended that the document be further developed and, where appropriate, the various subclauses be identified with their own standards. The Switchgear Assemblies Subcommittee of the Switchgear Committee of the IEEE Power Engineering So- ciety was responsible for this revision. This publication is one of a series covering switchgear assemblies as follows: IEEE Std C37.20.1 B6, Standard for Metal-Enclosed Low-V oltage Power Circuit Breaker Switchgear IEEE Std C37.20.2 B7, IEEE Standard for Metal-Clad Switchgear IEEE Std C37.20.3 B8, IEE