IEEE C37 122 4-2016 en Guide for Application and User Guide for Gas-Insulated Transmission Lines Rated 72 5 kV and Above.pdf

《IEEE C37 122 4-2016 en Guide for Application and User Guide for Gas-Insulated Transmission Lines Rated 72 5 kV and Above.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 122 4-2016 en Guide for Application and User Guide for Gas-Insulated Transmission Lines Rated 72 5 kV and Above.pdf（49页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Guide for Application and User Guide for Gas-Insulated Transmission Lines, Rated 72.5 kV and Above IEEE Std C37.122.4-2016 IEEE Power and Energy Society Sponsored by the Substations Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C37.122.4-2016 IEEE Guide for Application and Us

2、er Guide for Gas-Insulated Transmission Lines, Rated 72.5 kV and Above Sponsor Substations Committee of the IEEE Power and Energy Society Approved 15 May 2016 IEEE-SA Standards BoardAbstract: Guidance for the planning, permitting, design, equipment specification, installation, commissioning, operati

3、on, and maintenance of gas-insulated transmission lines is provided in this project. Only technical aspects are addressed in this guide. Commercial and legal issues associat- ed with gas-insulated transmission lines are not considered. This guide applies to ac transmission lines rated for maximum op

4、erating voltage of 72.5 kV and higher. Keywords: gas-insulated bus, gas-insulated cable, gas-insulated line, gas-insulated substation, gas-insulated switchgear, gas-insulated transmission line, GIB, GIC, GIL, GIS, IEEE C37.122.4 The Institute of Electrical and Electronics Engineers, Inc. 3 Park Aven

5、ue, New York, NY 10016-5997, USA Copyright 2017 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 15 May 2017. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; an

6、d quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence

7、of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought

8、about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any

9、duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropri- ate, seek the advice of a competent professional in determining th

10、e appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY , OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCURE- MENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOW

11、EVER CAUSED AND ON ANY THEORY OF LIABILITY , WHETHER IN CON- TRACT, STRICT LIABILITY , OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE

12、 WAS FORESEEABLE.4 Copyright 2017 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE stand

13、ard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a fo

14、rmal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards C

15、omments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertain- ing to IEEE Standards documents. Suggestions for changes in documents should be in the form

16、 of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concur- rence of a balance of interests. For this reason, IEEE and the member

17、s of its societies and Standards Coordi- nating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to pa

18、rticipate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should c

19、onsult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory require- ments. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE doe

20、s not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made avai

21、lable by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use an

22、d adop- tion by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2017 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any in

23、dividual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Ser- vice, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions o

24、f any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be ame

25、nded from time to time through the issuance of amendments, corri- genda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least e

26、very ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest e

27、dition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For

28、more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html.

29、 Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the exist

30、ence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Lett

31、ers of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrim- ination to applicants desiring to obtain such licen

32、ses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not re- sponsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether

33、 any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the valid- ity of any patent rights, and the risk of inf

34、ringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2017 IEEE. All rights reserved. Participants At the time this guide was submitted to the IEEE-SA Standards Board for approval, the Gas Insulated Substat

35、ions K5 Working Group had the following membership: Patrick Fitzgerald, Chair Darin Penner, Vice Chair Arun Arora George Becker Roberto Benato Philip Bolin Markus Etter Arnaud Ficheux Noboru Fujimoto David Giegel Jack Gustin Charles L. Hand Richard Jones Hermann Koch Devki Sharma Dave Solhtalab Ryan

36、 Stone The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. William Ackerman Ali Al A wazi Ficheux Arnaud Arun Arora Earle Bascom III George Becker Wallace Binder William Bloethe Gustavo Brunello William B

37、yrd Eldridge Byron Paul Cardinal Robert Christman Denis Dufournet Edgar Dullni Markus Etter Jorge Fernandez Daher Patrick Fitzgerald Frank Gerleve David Giegel Jalal Gohari Edwin Goodwin James Graham Randall Groves Charles Hand Gary Heuston Werner Hoelzl Andrew Jones Hermann Koch J Koepfinger Jim Ku

38、lchisky Chung-Yiu Lam Benjamin Lanz Hua Liu Jorge Marquez Omar Mazzoni David Mitchell Georges Montillet Arun Narang Michael Newman Carl Orde Lorraine Padden Mirko Palazzo Bansi Patel Darin Penner Douglas Proctor Larry Putman Michael Roberts Jesse Rorabaugh Bartien Sayogo Devki Sharma David Solhtalab

39、 John Spare Gary Stoedter Ryan Stone John Toth John Vergis Jane Verner Mark Waldron Mark Walton Kenneth White James Wilson Jonathan Woodworth Jian Yu Xi Zhu When the IEEE-SA Standards Board approved this guide on 15 May 2016, it had the following membership: Jean-Philippe Faure, Chair Ted Burse, Vic

40、e Chair John D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Stephen Dukes Jianbin Fan J. Travis Griffith Gary Hoffman Ronald W. Hotchkiss Michael Janezic Joseph L. Koepfinger* Hung Ling Kevin Lu Annette D. Reilly Gary Robinson Mehmet Ulema Yingli Wen Howard W

41、olfman Don Wright Yu Yuan Daidi Zhong *Member Emeritus7 Copyright 2017 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std C37.122.4-2016, IEEE Guide for Application and User Guide for Gas- Insulated Transmission Lines, Rated 72.5 kV and Above. Gas-insulated line (GIL)

42、has been manufactured starting in the early 1970s when the first gas-insulated substa- tions were introduced. IEEE has not had any standard to address any manufacturing of GIL. To address IEEE policy that IEEE standards should be harmonized with international standards whenever possible, a study was conducted by a joint task force of the Substations Committee and the International Electrotechnical Commis- sion (IEC). This included creating an IEEE Standard that generally aligned with the IEC GIL standards.