IEEE 1861-2014 en Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above《1000 kV交流电及以上的电气设备和系统调试现场验收试验指南》.pdf

《IEEE 1861-2014 en Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above《1000 kV交流电及以上的电气设备和系统调试现场验收试验指南》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1861-2014 en Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above《1000 kV交流电及以上的电气设备和系统调试现场验收试验指南》.pdf（70页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above Sponsored by the Corporate Advisory Group IEEE Substations Committee IEEE Switchgear Committee IEEE Transformers Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE-SA Board of

2、 Governors and IEEE Power and Energy Society IEEE Std 1861-2014 IEEE Std 1861-2014 IEEE Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above Sponsor Corporate Advisory Group of the IEEE Board of Governors and IEEE Substations Committee IEEE Swit

3、chgear Committee IEEE Transformers Committee of the IEEE Power and Energy Society Approved 12 June 2014 IEEE-SA Standards Board Abstract: On-site acceptance tests of ultra-high-voltage power equipment are subject to this guide. Criteria and requirements for test items, conditions, methods, and resul

4、ts are established. The stated specifications and requirements, both technical and for testing, are universally needed for acceptance tests on-site and commissioning of ultra-high-voltage power equipment, including power transformers, reactors, capacitive voltage transformers, bushing-type current t

5、ransformers, gas-insulated switchgear, air insulated grounding switches, air insulated disconnecting switches, bushings, metal-oxide surge arresters, suspension insulators, post insulators, and insulating oil, etc. It will be sufficient for most installations. Keywords: air-insulated disconnecting s

6、witch, air-insulated grounding switch, bushing, bushing-type current transformer, capacitive voltage transformer, factory test, gas-insulated switchgear, IEEE 1861, insulating oil, system commissioning, metal-oxide surge arrester, on-site acceptance test, post insulator, power transformer, reactor,

7、suspension insulator, ultra-high voltage. The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2014 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 1 August 2014. Printed in the United States o

8、f America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standard

9、s documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standar

10、d. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or renderin

11、g professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable

12、care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED

13、 TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE

14、UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version

15、 published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committee

16、s and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual r

17、ather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards document

18、s. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a

19、 balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to

20、 interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws a

21、nd regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referr

22、ing to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under U.

23、S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and

24、methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions

25、 of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy po

26、rtions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or ma

27、y be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at l

28、east every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the la

29、test edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address

30、listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata

31、/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect

32、to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Le

33、tters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licen

34、ses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether a

35、ny licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infring

36、ement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Participants At the time this IEEE guide was completed, the P1861 sub-working group of Ultra-High-Voltage AC Standards Working Group had the following membership: Bo L

37、i, Chair Hui Chao, Co-Chair Jiangbo Chen, Secretary Ying Li, Secretary Raj Ahuja Liangeng Ban Weijiang Chen Denis Dufournet Ken Edwards Jianbin Fan Francois Gallon Jian Guo Hiroyuki Hama Jing Han Fengjun He Yan He Hiroki Ito Hermann Koch Guangfan Li Liuling Li Makoto Miyashita Masatomo Ono Yukiyasu

38、Shirasaka Kyoichi Uehara Xiaogang Wang Xiaoning Wang Yang Xiao Yonghua Yin Yu Yin Bin Zheng Jian Zhang Cuixia Zhang Shuqi Zhang The Working Group gratefully acknowledges the contributions of the following entities and participants. Without their assistance and dedication, this standard would not hav

39、e been completed. The following entities submitted technical contributions or commented of the draft standard at various stages of the project development. Alstom Grid Bonneville Power Administration Hitachi, Ltd. InterNational Electrical Testing Association (NETA) Japan AE Power Systems Corporation

40、 Mitsubishi Electric Corporation Quanta Technology LLC Siemens Corporation State Grid Corporation of China (SGCC) Toshiba Corporation Waukesha Electric Systems, Inc. The following members of the entity balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or ab

41、stention. Alstom Beijing Jiaotong University Beijing Sifang Automation Co., Ltd BII Group Holdings Ltd. China Datang Corporation Hitachi, Ltd. InterNational Electrical Testing Association (NETA) Marvell Semiconductor, Inc. Mitsubishi Electric Corporation Quanta Technology LLC Siemens Corporation Sou

42、thwest Jiaotong University State Grid Corporation of China (SGCC) Toshiba Corporation Waukesha Electric Systems, Inc.Copyright 2014 IEEE. All rights reserved. vi When the IEEE-SA Standards Board approved this guide on 12 June 2014, it had the following membership: John Kulick, Chair Jon Walter Rosda

43、hl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Peter Balma Farooq Bari Ted Burse Clint Chaplin Stephen Dukes Jean-Philippe Faure Gary Hoffman Michael Janezic Jeffrey Katz Joseph L. Koepfinger* David J. Law Hung Ling Oleg Logvinov Ted Olsen Glenn Parsons Ron Petersen

44、 Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Don Wright Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Patrick Gibbons IEEE-SA Content Publishing Soo Kim IE

45、EE-SA Standards Technical Community Copyright 2014 IEEE. All rights reserved. vii Introduction This introduction is not part of IEEE Std 1861-2014, IEEE Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above. With the increase in voltage levels, t

46、he reliability and safety of high-voltage electric equipment is facing new challenges. There is a need to have consensus on a series of technical criteria and requirements for on-site acceptance tests for ultra-high-voltage (UHV) electric equipment to detect the damages or abnormal conditions that m

47、ay occur during the transportation and installation processes and to determine whether equipment can be put into operation reliably and safely for power systems. AC transmission systems of 1000 kV or greater have been established and operated with full-voltage in China and are also currently in vari

48、ous stages of development in other countries. However, there is a lack of suitable UHV transmission system commissioning procedures and technical information. Therefore, it is necessary to formulate a series of consensus technical requirements and criteria so as to facilitate the development of UHV

49、systems and help ensure their successful commissioning. This guide proposes on-site acceptance tests, relevant test items, test methods, and evaluation criteria for power transformers, reactors, capacitive voltage transformers (CVTs), bushing-type current transformers (CTs), gas-insulated switchgear, air-insulated grounding switches, air-insulated disconnecting switches, bushings, metal-oxide surge arresters (MOSAs), suspension insulators, post insulators, and insulating oil. System commissioning consists of two parts. The first part is the preparation work before commissionin