IEC 62756-1-2015 Digital load side transmission lighting control (DLT) - Part 1 Basic requirements《数字负荷端传输照明控制 (DLT) 第1部分 基本要求》.pdf

《IEC 62756-1-2015 Digital load side transmission lighting control (DLT) - Part 1 Basic requirements《数字负荷端传输照明控制 (DLT) 第1部分 基本要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 62756-1-2015 Digital load side transmission lighting control (DLT) - Part 1 Basic requirements《数字负荷端传输照明控制 (DLT) 第1部分 基本要求》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62756-1 Edition 1.0 2015-05 INTERNATIONAL STANDARD Digital load side transmission lighting control (DLT) Part 1: Basic requirements IEC 62756-1:2015-05(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specifi

2、ed, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about

3、IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch

4、Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is

5、 kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standard

6、s, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also

7、 gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.

8、org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/g

9、lossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore

10、.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62756-1 Edition 1.0 2015-05 INTERNATIONAL STANDARD Digital load side transmission lighting control (DLT) Part 1: Basic requirements INTERNATIONA

11、L ELECTROTECHNICAL COMMISSION ICS 29.140.99 ISBN 978-2-8322-2711-4 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 IEC 62756-1:2015 IEC 2015 CONTENTS FOREWORD . 5 INTRODUCTION

12、. 7 1 Scope 8 2 Normative references 8 3 Terms and definitions 8 4 General description . 10 4.1 General . 10 4.2 Master-slave structure 10 4.3 Specification overview 10 5 General requirements 10 5.1 Voltage rating . 10 5.2 Frequency rating . 11 5.3 Marking of control devices and control gear 11 6 El

13、ectrical specification . 11 6.1 General . 11 6.2 Wiring method . 12 6.3 Wiring diagram 12 6.4 Block diagram of the control gear 12 6.5 Block diagram of the control device . 13 6.6 Electrical characteristics in different periods of the mains waveform . 13 6.6.1 General . 13 6.6.2 Separation of the ha

14、lf-wave into time periods 14 6.6.3 Electrical characteristics of the supply period 14 6.6.4 Electrical characteristics of the operating period 19 6.6.5 Electrical characteristics of the data period 19 6.7 Data signal voltage range and timing 23 6.8 Power up timing 23 6.9 Electrical characteristics d

15、uring the off state of control gear 24 6.9.1 General . 24 6.9.2 Power controlled off state 24 6.9.3 Telegram controlled off state . 25 7 Data timing 25 7.1 General . 25 7.2 Information bit timing 25 7.3 Permissible frames . 25 8 Telegram structure 26 8.1 General . 26 8.2 Telegrams . 27 8.2.1 General

16、 . 27 8.2.2 Group number . 27 8.2.3 Telegram type . 27 8.2.4 Parity bit 27 8.2.5 Data for control of the control gear 27 9 Definition of telegram types . 27 9.1 Summary of telegram types 27 IEC 62756-1:2015 IEC 2015 3 9.2 Telegram type 0: Brightness . 28 9.3 Telegram type 1: Colour control 28 9.4 Te

17、legram type 2: Colour temperature control 29 9.5 Telegram type 3 29 9.6 Telegram type 4 29 9.7 Telegram type 5: commissioning: Group number assignment 29 9.8 Telegram type 6: Manufacturer specific . 30 9.9 Telegram type 7: extended telegram . 30 10 Method of operation . 30 10.1 General . 30 10.2 Bri

18、ghtness 31 10.2.1 General . 31 10.2.2 Response time . 31 10.2.3 Light output level . 31 10.2.4 Start-up . 31 10.3 Colour control . 31 10.3.1 General . 31 10.3.2 Colour (x, y) . 31 10.3.3 Response time . 32 10.3.4 Colour gamut . 32 10.3.5 Start-up . 32 10.4 Colour temperature control . 33 10.4.1 Gene

19、ral . 33 10.4.2 CCT (correlated colour temperature) . 33 10.4.3 Response time . 33 10.4.4 Start-up . 33 10.5 Telegram controlled group number assignment . 33 10.6 Manufacturer specific telegram . 34 11 Test procedures 34 11.1 General . 34 11.2 Electrical characteristics tests . 35 11.2.1 General . 3

20、5 11.2.2 Test of control device 35 11.2.3 Test of control gear . 38 11.3 Test of data timing 41 11.4 Test of telegram structure . 41 11.4.1 Test of control device 41 11.4.2 Test of control gear . 41 11.5 Test of telegram types 42 11.5.1 General . 42 11.5.2 Rejection of unsupported telegram types . 4

21、2 11.5.3 Test of telegram type 0: brightness 42 11.5.4 Test of telegram type 1: colour control . 42 11.5.5 Test of telegram type 2: colour temperature control . 43 11.5.6 Test of telegram type 5: commissioning . 43 11.5.7 Test of telegram type 6: manufacturer specific . 43 11.6 Test of method of ope

22、ration 43 11.6.1 General . 43 11.6.2 Group number operation 43 4 IEC 62756-1:2015 IEC 2015 Annex A (informative) Examples of procedures for telegram controlled group number commissioning . 47 A.1 Telegram controlled group number assignment of a new system . 47 A.2 Telegram controlled group number as

23、signment of replacement control gear . 47 A.3 Telegram controlled changing of group numbers . 48 Figure 1 Example wiring diagram . 12 Figure 2 Example of block diagram of control gear . 13 Figure 3 Example of block diagram of control device 13 Figure 4 Time periods of each half-wave 14 Figure 5 Timi

24、ng of supply period 15 Figure 6 Timing data period . 20 Figure 7 Rise time and fall time at the control interface 23 Figure 8 Transmission of “start of telegram” . 25 Figure 9 Transmission of first bit 0, second bit 0 25 Figure 10 Transmission of first bit 0, second bit 1 26 Figure 11 Transmission o

25、f first bit 1, second bit 0 26 Figure 12 Transmission of first bit 1, second bit 1 26 Figure 13 Brightness telegram . 28 Figure 14 Colour control telegram 28 Figure 15 Colour temperature telegram 29 Figure 16 Group number assignment telegram . 29 Figure 17 Manufacturer specific telegram. 30 Figure 1

26、8 The CIE 1931 colour space chromaticity diagram . 32 Figure 19 Test Circuit for testing the Control Device 35 Figure 20 Test Circuit for testing the Control Gear . 38 Figure 21 Voltage applied to control gear for test procedure 39 Table 1 Nominal mains voltage 100 V, frequency 50 Hz or 60 Hz . 17 T

27、able 2 Nominal mains voltage 120 V; frequency 50 Hz or 60 Hz . 17 Table 3 Nominal mains voltage 200 V; frequency 50 Hz or 60 Hz . 18 Table 4 Nominal mains voltage 230 V; frequency 50 Hz or 60 Hz . 18 Table 5 Nominal mains voltage 277 V; frequency 50 Hz or 60 Hz . 19 Table 6 Nominal mains voltage 100

28、 V; frequency 50 Hz or 60 Hz . 21 Table 7 Nominal mains voltage 120 V; frequency 50 Hz or 60 Hz . 21 Table 8 Nominal mains voltage 200 V; frequency 50 Hz or 60 Hz . 21 Table 9 Nominal mains voltage 230 V; frequency 50 Hz or 60 Hz . 22 Table 10 Nominal mains voltage 277 V; frequency 50 Hz or 60 Hz .

29、22 Table 11 Electrical characteristics of the data signal 23 Table 12 Currents and Voltages for control gear during the power controlled off state . 24 Table 13 Telegram types . 28 Table 14 Dimming characteristic 31 Table 15 Parameters for testing purposes 35 Table 16 Group number test telegram sequ

30、ence 44 IEC 62756-1:2015 IEC 2015 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIGITAL LOAD SIDE TRANSMISSION LIGHTING CONTROL (DLT) Part 1: Basic requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national ele

31、ctrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specif

32、ications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Internati

33、onal, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal

34、 decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for

35、international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4)

36、In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall

37、be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certific

38、ation bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury

39、, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cit

40、ed in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifyi

41、ng any or all such patent rights. International Standard IEC 62756-1 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. The text of this standard is based on the following documents: CDV Report on voting 34C/1054/CDV 34C/1081B/RV

42、C Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62756 series, published under the general title Di

43、gital load side transmission lighting control (DLT), can be found on the IEC website. 6 IEC 62756-1:2015 IEC 2015 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data rela

44、ted to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it co

45、ntains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. IEC 62756-1:2015 IEC 2015 7 INTRODUCTION This standard concerning Digital Load Side Transmission Lighting Control (DLT) describes a proto

46、col for simple control of brightness, colour, colour temperature, and other parameters for the purpose of controlling lighting sources such as CFLi, LED light engines, electronic control gear and any other light source with integrated or external control gear. This protocol uses existing wiring and

47、allows easy retrofit of standard switches, dimmers and lamps with the new devices described in this standard, with little or no configuration. The following standards contain safety requirements for control devices and control gear: IEC 60669-2-1, Switches for household and similar fixed electrical

48、installations Part 2-1: Particular requirements Electronic switches, IEC 61347, Lamp control gear, IEC 60968, Self-ballasted lamps for general lighting services Safety requirements, IEC 62560, Self-ballasted LED-lamps for general lighting services by voltage 50 V Safety specifications. 8 IEC 62756-1

49、:2015 IEC 2015 DIGITAL LOAD SIDE TRANSMISSION LIGHTING CONTROL (DLT) Part 1: Basic requirements 1 Scope This International Standard specifies a protocol, electrical interface and test procedures for control of electronic lighting equipment by digital signals over the load side mains wiring. Safety requirements are not covered by this standard. 2 Normative references The following documents, in whole or in part, are nor