IEC 61643-312-2013 Components for low-voltage surge protective devices - Part 312 Selection and application principles for gas discharge tubes《低压浪涌保护装置的元件.第312部分 气体放电管的选择和应用原则 》.pdf

《IEC 61643-312-2013 Components for low-voltage surge protective devices - Part 312 Selection and application principles for gas discharge tubes《低压浪涌保护装置的元件.第312部分 气体放电管的选择和应用原则 》.pdf》由会员分享，可在线阅读，更多相关《IEC 61643-312-2013 Components for low-voltage surge protective devices - Part 312 Selection and application principles for gas discharge tubes《低压浪涌保护装置的元件.第312部分 气体放电管的选择和应用原则 》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61643-312 Edition 1.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Components for low-voltage surge protective devices Part 312: Selection and application principles for gas discharge tubes Composants pour parafoudres basse tension Partie 312: Principes de choix et dapplication pour les

2、tubes dcharge de gaz IEC 61643-312:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocop

3、ying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local

4、IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms,

5、 sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de

6、 rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for

7、 all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications s

8、earch - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to dat

9、e on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in Engl

10、ish and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Ser

11、vice Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le conte

12、nu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications

13、 CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille

14、les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les ter

15、mes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61643-312 Ed

16、ition 1.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Components for low-voltage surge protective devices Part 312: Selection and application principles for gas discharge tubes Composants pour parafoudres basse tension Partie 312: Principes de choix et dapplication pour les tubes dcharge de

17、gaz INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE S ICS 31.100; 33.040.99 PRICE CODE CODE PRIX ISBN 978-2-83220-740-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Ma

18、ke sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61643-312 IEC:2013 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Terms, definitions and symbols 6 3.1 Terms a

19、nd definitions 6 3.2 Symbols 10 4 Service conditions 10 4.1 General . 10 4.2 Low temperature . 10 4.3 Air pressure and altitude . 10 4.4 Ambient temperature . 10 4.5 Relative humidity . 11 5 Mechanical requirements and materials 11 5.1 General . 11 5.2 Robustness of terminations . 11 5.3 Solderabili

20、ty 11 5.4 Radiation . 11 5.5 Marking . 11 6 General 11 7 Construction . 12 7.1 Design . 12 7.2 Description 12 7.3 Fail-short (failsafe) 13 8 Function . 14 8.1 Protection principle 14 8.2 Operating mode . 14 8.3 Response behaviour 14 8.3.1 Static response behavior . 14 8.3.2 Dynamic response behavior

21、 . 14 8.4 Fail-short (failsafe) 15 9 Applications 16 9.1 Protective circuits 16 9.1.1 General . 16 9.1.2 2-point (signal line) protection . 16 9.1.3 3-point protection 17 9.1.4 5-point protection 18 9.2 Telephone/fax/modem protection . 19 9.3 Cable TV/coaxial cable protection . 19 9.4 AC line protec

22、tion 20 Bibliography 21 Figure 1 Voltage and current characteristics of a GDT . 8 Figure 2 Symbol for a two-electrode GDT 10 Figure 3 Symbol for a three-electrode GDT 10 Figure 4 Example of a two-electrode GDT . 12 61643-312 IEC:2013 3 Figure 5 Example of a three-electrode GDT 12 Figure 6 Failsafe c

23、onstruction of a three-electrode GDT using a solder pill as sensitive spacer 13 Figure 7 Failsafe construction of a three-electrode GDT, using a plastic foil as sensitive spacer 13 Figure 8 Typical response behaviour of a 230 V GDT 15 Figure 9 Spark-over voltages versus response time . 15 Figure 10

24、Current through the GDT versus response time of fail-short (failsafe) . 16 Figure 11 2-point (Signal line) protection . 17 Figure 12 3-point protection using two-electrode GDTs . 17 Figure 13 3-point protection using three-electrode GDTs 17 Figure 14 3-point protection using two-electrode GDTs with

25、fail-short . 18 Figure 15 3-point protection using three-electrode GDTs with fail-short . 18 Figure 16 5-point protection using two-electrode GDTs . 18 Figure 17 5-point protection using three-electrode GDTs 18 Figure 18 5-point protection using two-electrode GDTs with fail-short . 19 Figure 19 5-po

26、int protection using three-electrode GDTs with fail-short . 19 Figure 20 Telephone/fax/modem protection using two-electrode GDTs 19 Figure 21 Telephone/fax/modem protection using three-electrode GDTs 19 Figure 22 Cable TV/ coaxial cable protection . 20 Figure 23 AC line protection . 20 4 61643-312 I

27、EC:2013 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COMPONENTS FOR LOW-VOLTAGE SURGE PROTECTIVE DEVICES Part 312: Selection and application principles for gas discharge tubes FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising al

28、l national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Te

29、chnical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory w

30、ork. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.

31、 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recomm

32、endations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any

33、 end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publ

34、ication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by indepe

35、ndent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any p

36、ersonal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative

37、references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible

38、 for identifying any or all such patent rights. International Standard IEC 61643-312 has been prepared by subcommittee 37B: Specific components for surge arresters and surge protective devices, of IEC technical committee 37: Surge arresters. The text of this standard is based on the following docume

39、nts: FDIS Report on voting 37B/114/FDIS 37B/120/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above Table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 6164

40、3 series, under the general title Components for low-voltage surge protective devices can be found on the IEC website. 61643-312 IEC:2013 5 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/websto

41、re.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 61643-312 IEC:2013 COMPONENTS FOR LOW-VOLTAGE SURGE PROTECTIVE DEVICES Part 312: Selection and application principles for gas dischar

42、ge tubes 1 Scope This part of IEC 61643 is applicable to gas discharge tubes (GDT) used for overvoltage protection in telecommunications, signalling and low-voltage power distribution networks with nominal system voltages up to 1 000 V (r.m.s.) a.c. and 1 500 V d.c. They are defined as a gap, or sev

43、eral gaps with two or three metal electrodes hermetically sealed so that gas mixture and pressure are under control. They are designed to protect apparatus or personnel, or both, from high transient voltages. This standard provides information about the characteristics and circuit applications of GD

44、Ts having two or three electrodes. This standard does not specify requirements applicable to complete surge protective devices, nor does it specify total requirements for GDTs employed within electronic devices, where precise coordination between GDT performance and surge protective device withstand

45、 capability is highly critical. This part of IEC 61643 does not deal with mountings and their effect on GDT characteristics. Characteristics given apply solely to GDTs mounted in the ways described for the tests; does not deal with mechanical dimensions; does not deal with quality assurance requirem

46、ents; may not be sufficient for GDTs used on high-frequency (30 MHz); does not deal with electrostatic voltages; does not deal with hybrid overvoltage protection components or composite GDT devices. 2 Normative references The following documents, in whole or in part, are normatively referenced in th

47、is document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold IEC 60068-2-20, Env

48、ironmental testing Part 2-20: Tests Test T: Test methods for solderability and resistance to soldering heat of devices with leads IEC 60068-2-21, Environmental testing Part 2-21: Tests Test U: Robustness of terminations and integral mounting devices IEC 61643-311, Components for low-voltage surge pr

49、otective devices Part 311: Specification for gas discharge tubes (GDT) 3 Terms, definitions and symbols 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply: 61643-312 IEC:2013 7 3.1.1 arc current current that flows after sparkover when the circuit impedance allows a current to flow that exceeds the glow-to-arc transition cu