IEC 60738-1-2006 Thermistors - Directly heated positive temperature coefficient - Part 1 Generic specification《热敏电阻器.直热式正温度系数.第1部分 总规范》.pdf

《IEC 60738-1-2006 Thermistors - Directly heated positive temperature coefficient - Part 1 Generic specification《热敏电阻器.直热式正温度系数.第1部分 总规范》.pdf》由会员分享，可在线阅读，更多相关《IEC 60738-1-2006 Thermistors - Directly heated positive temperature coefficient - Part 1 Generic specification《热敏电阻器.直热式正温度系数.第1部分 总规范》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IEC60738-1QC 440000Third edition2006-04Thermistors Directly heated positive temperature coefficient Part 1: Generic specification Reference number IEC 60738-1:2006(E) Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo re

2、production or networking permitted without license from IHS-,-,-Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated v

3、ersions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publ

4、ications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Infor

5、mation on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue o

6、n the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just

7、Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance

8、, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL S

9、TANDARD IEC60738-1QC 440000Third edition2006-04Thermistors Directly heated positive temperature coefficient Part 1: Generic specification IEC 2006 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includin

10、g photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch XA For price, see current

11、cataloguePRICE CODE Commission Electrotechnique InternationaleInternational Electrotechnical Commission Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 2 60738-1 IEC:2006(E)

12、CONTENTS FOREWORD.5 1 Scope.7 2 Normative references .7 3 Terms and definitions .8 4 Units and symbols 16 5 Preferred values.17 5.1 Climatic categories17 5.2 Marking .17 5.3 Spacings .18 6 Quality assessment procedures18 6.1 General .18 6.2 Primary stage of manufacture19 6.3 Subcontracting 19 6.4 St

13、ructurally similar components.19 6.5 Qualification approval procedures .20 6.6 Rework and repair .27 6.7 Release for delivery 27 6.8 Certified test records of released lots 28 6.9 Delayed delivery28 6.10 Alternative test methods28 6.11 Manufacture outside the geographical limits of IECQ NSIs 28 6.12

14、 Unchecked parameters28 7 Test and measurement procedures.28 7.1 General .28 7.2 Standard conditions for testing 29 7.3 Drying and recovery 29 7.4 Visual examination and check of dimensions.30 7.5 Zero-power resistance.30 7.6 Temperature coefficient of resistance31 7.7 Insulation resistance (for ins

15、ulated types only) 31 7.8 Voltage proof (for insulated types only) .32 7.9 Resistance/temperature characteristic.32 7.10 Dissipation factor at Umax() .33 7.11 Response time by ambient temperature change (ta)34 7.12 Response time by power change (tp).34 7.13 Thermal time constant by ambient temperatu

16、re change (a) 35 7.14 Thermal time constant by cooling (c)35 7.15 Robustness of terminations .37 7.16 Solderability 38 7.17 Resistance to soldering heat .39 7.18 Rapid change of temperature 40 7.19 Vibration40 7.20 Bump 40 7.21 Shock41 Copyright International Electrotechnical Commission Provided by

17、IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-60738-1 IEC:2006(E) 3 7.22 Climatic sequence .41 7.23 Damp heat, steady state42 7.24 Endurance.43 7.25 Tripping current and tripping time46 7.26 Non-tripping current 47 7.27 Residual current

18、47 7.28 Surface temperature47 7.29 Inrush current48 7.30 Mounting (for surface mount thermistors only).49 7.31 Shear (adhesion) test 50 7.32 Substrate bending test 50 Annex A (normative) Interpretation of sampling plans and procedures as described in IEC 60410 for use within the IEC quality assessme

19、nt system for electronic components (IECQ) 51 Annex B (informative) Mounting for electrical measurements (except surface mount types) .52 Annex C (informative) Mounting for temperature measurements 55 Figure 1 Typical resistance-temperature characteristic and definitions for PTC thermistors (at zero

20、 power) .10 Figure 2 Typical R-TNF characteristic for PTC thermistors in sensor applications 11 Figure 3 Typical current/voltage characteristic for PTC thermistors 11 Figure 4 Iinagainst t at Udc14 Figure 5 Iinagainst t at Urms15 Figure 6 Dissipation factor test circuit 33 Figure 7 Temperature gradi

21、ent.34 Figure 8 Circuit for measurement of thermal time constant by cooling36 Figure 9 Circuit for endurance at maximum operating temperature and maximum voltage45 Figure 10 Circuit for surface temperature measurement.48 Figure 11 Measuring circuit48 Figure B.1 Example of a preferred mounting method

22、 for thermistors without wire terminations52 Figure B.2 Example of a preferred mounting method for thermistors with wire terminations53 Figure B.3 Example of a preferred mounting method for surface mount thermistors .54 Figure C.1 Example of a preferred mounting method for temperature measurement on

23、 cylindrical heating elements .55 Table 1 Creepage distances and clearances18 Table 2 Fixed sample size test schedule for qualification approval of thermistors for current limitation Assessment level EZ.22 Table 3 Fixed sample size test schedule for qualification approval of thermistors for use as h

24、eating elements Assessment level EZ.23 Table 4 Fixed sample size test schedule for qualification approval of thermistors for inrush current application Assessment level EZ .24 Table 5 Fixed sample size test schedule for qualification approval of thermistors for use as temperature sensing elements, A

25、ssessment level EZ 25 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 4 60738-1 IEC:2006(E) Table 6 Quality conformance inspection for lot-by-lot inspection 26 Table 7 Qualit

26、y conformance inspection for periodic testing.27 Table 8 Tensile force .37 Table 9 Number of cycles per climatic category .42 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6

27、0738-1 IEC:2006(E) 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ THERMISTORS DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT Part 1: Generic specification FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrot

28、echnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specificati

29、ons, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International,

30、 governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decis

31、ions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for intern

32、ational use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In ord

33、er to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be cle

34、arly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability sha

35、ll attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including leg

36、al fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this pub

37、lication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60738-1 has been prepared by IEC technical committee 4

38、0: Capacitors and resistors for electronic equipment. This third edition cancels and replaces the second edition published in 1998 and constitutes a minor revision. The changes with respect to the previous edition refer to the tables, figures and references. The text of this standard is based on the

39、 following documents: FDIS Report on voting 40/1651/FDIS 40/1730/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for R

40、esaleNo reproduction or networking permitted without license from IHS-,-,- 6 60738-1 IEC:2006(E) This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The QC number that appears on the front cover of this publication is the specification number in the IEC Quality Asses

41、sment System for Electronic Components (IECQ). IEC 60738 consists of the following parts, under the general title Thermistors Directly heated positive step-function coefficient: Part 1: Generic specification Part 1-1: Blank detail specification Current limiting application Assessment level EZ Part 1

42、-2: Blank detail specification Heating element application Assessment level EZ Part 1-3: Blank detail specification Inrush current application Assessment level EZ Part 1-4: Blank detail specification Sensing application Assessment level EZ The committee has decided that the contents of this publicat

43、ion will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of thi

44、s standard may be issued at a later date. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-60738-1 IEC:2006(E) 7 THERMISTORS DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT Pa

45、rt 1: Generic specification 1 Scope This part of IEC 60738 describes terms and methods of test for positive step-function temperature coefficient thermistors, insulated and non-insulated types typically made from ferro-electric semi-conductor materials. It establishes standard terms, inspection proc

46、edures and methods of test for use in detail specifications for Qualification Approval and for Quality Assessment Systems for electronic components. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the editio

47、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60027 (all parts), Letter symbols to be used in electrical technology IEC 60050 (all parts), International Electrotechnical Vocabulary (IEV) IEC 60062, Marking codes for res

48、istors and capacitors IEC 60068-1:1988, Environmental testing Part 1: General and guidance Amendment 1 (1992) IEC 60068-2-1:1990, Environmental testing Part 2: Tests Tests A: Cold Amendment 1 (1993) Amendment 2 (1994) IEC 60068-2-2:1974, Environmental testing Part 2: Tests Tests B: Dry heat Amendment 1 (1993) IEC 60068-2-6, Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-11, Environmental testing Part 2: Tests Test