TIA-470 210-C-2004 Telecommunications Telephone Terminal Equipment Resistance and Impedance Performance Requirements for Analog Telephones《电信 电话终端设备 模拟电话的阻抗性能要求》.pdf

《TIA-470 210-C-2004 Telecommunications Telephone Terminal Equipment Resistance and Impedance Performance Requirements for Analog Telephones《电信 电话终端设备 模拟电话的阻抗性能要求》.pdf》由会员分享，可在线阅读，更多相关《TIA-470 210-C-2004 Telecommunications Telephone Terminal Equipment Resistance and Impedance Performance Requirements for Analog Telephones《电信 电话终端设备 模拟电话的阻抗性能要求》.pdf（35页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA STANDARD Telecommunications Telephone Terminal Equipment Resistance and Impedance Performance Requirements for Analog Telephones TIA-470.210-C Revision of TIA/EIA-470-B) APRIL 2004 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Elect

2、ronic Industries Alliance ANSI/TIA-470.210-C-2004 Approved: April 20, 2004 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are

3、designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The e

4、xistence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-T

5、IA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to pa

6、rties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the

7、 applicability of regulatory limitations before its use. (From Standards Proposal No. 3-4350.210-RV3, formulated under the cognizance of the TIA TR-41.3 Subcommittee on Analog and Digital Wireline Terminals.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2004 Standards and Technology Departme

8、nt 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search online at http

9、:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PLEASE! DONT VIOLATE THE LAW! This documen

10、t is copyrighted by the TIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 U.S.A

11、. or call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The doc

12、ument to which this Notice is affixed has been prepared by one or more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the

13、authors of the contents. TIA Engineering Committees are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm. TIAs function is to adminis

14、ter the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (

15、“IPR”), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN

16、ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURA

17、CY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WAR

18、RANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL

19、 OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGA

20、TION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without

21、 license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C The TR-41.3.6 Working Group acknowledges the contribution made by the following individuals i

22、n the development of this standard. Name Representing Position (If Applicable) Don McKinnon AST Technology Labs, Inc. Chair / Editor Rick Carey RadioShack Editor Dave Stenner Advent Instruments, Inc. Fred Bonhomme Atlinks Ken Macdonald Microtronix Systems Ltd. Amar Ray Sprint Al Baum Uniden Steve Wh

23、itesell VTech The TR-41.3.6 Working Group, which had the technical responsibility during the development of this standard, had the following participating members. Name Representing James Bress AST Technology Labs Jim McNeill Atlinks Jim Mazzolini Casio Communications Pierluigi Pacciardi Casio Commu

24、nications Rick White CIDCO Communications John Bareham Consultant in Electroacoustics Len Bleile ESP Berndt Martenson ETSI Harry Van Zandt ESC Technologies Ken Macdonald Microtronix Systems Steve Kropp VTech Copyright Telecommunications Industry Association Provided by IHS under license with EIANot

25、for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C i TABLE OF CONTENTS 1 SCOPE _1 2 REF

26、ERENCES_2 2.1 NORMATIVE REFERENCES _2 2.2 INFORMATIVE REFERENCES _2 3 ABBREVIATIONS, ACRONYMS, AND DEFINITIONS _3 3.1 ABBREVIATIONS AND ACRONYMS _3 3.2 DEFINITIONS _3 4 TECHNICAL REQUIREMENTS _4 4.1 CATEGORIES OF CRITERIA_4 4.2 REQUIREMENTS MODEL_4 4.3 TEST EQUIPMENT PERFORMANCE _4 4.4 DC FEED CIRCU

27、IT _5 4.5 ON-HOOK RESISTANCE _6 4.5.1 Requirements6 4.5.2 Method of Measurement 6 4.6 OFF-HOOK RESISTANCE _8 4.6.1 dc Resistance8 4.6.1.1 Requirements. 8 4.6.1.2 Method of Measurement 8 4.6.2 Simulated Open Switch Interval Recovery Time.10 4.6.2.1 Requirements. 10 4.6.2.2 Method of Measurement 10 4.

28、7 ON-HOOK IMPEDANCE _11 4.7.1 dc Current During Ringing.12 4.7.1.1 Requirements. 12 4.7.1.2 Method of Measurement 12 4.7.2 Metallic Impedance During Ringing13 4.7.2.1 Requirement 13 4.7.2.2 Method of Measurement 13 4.7.3 Longitudinal Impedance During Ringing 14 4.7.3.1 Requirements. 14 4.7.3.2 Metho

29、d of Measurement 14 4.7.4 Longitudinal Impedance for ac Power Induction from Power Lines .15 4.7.4.1 Requirements. 15 4.7.4.2 Method of Measurement 15 4.7.5 On-Hook Metallic Impedance (5 Hz to 200 Hz, 1 Vrms to 10 Vrms) .16 4.7.5.1 Requirement 16 4.7.5.2 Method of Measurement 16 4.7.6 In-Band On-Hoo

30、k Metallic Impedance (200 to 3200 Hz) .17 4.7.6.1 Requirement 17 4.7.6.2 Method of Measurement 17 4.8 OFF-HOOK METALLIC IMPEDANCE (RETURN LOSS) _18 4.8.1 Requirements18 4.8.2 Method of Measurement 18 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for Resa

31、leNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C ii 4.9 LONGITUDINAL BALANCE _ 20 4.9.1 Requirement .20 4.9.2 Method of Measurement.20 ANNEX A (INFORMATIVE) Scaled On-Hook Performance Limits Based On CPE Quantity Connected At The CI _ 21 ANNEX B (INFORMATIVE) ISO

32、R-40 Frequencies _ 22 ANNEX C (INFORMATIVE) Longitudinal Balance Method Of Measurement _ 23 Table of Figures Figure 1 One possible dc Feed Circuit .5 Figure 2 On-Hook Resistance Requirements6 Figure 3 On-Hook Resistance between Tip and Ring 7 Figure 4 On-Hook Resistance Tip-to-Ring with Ring grounde

33、d and Tip-to-Ring with Tip grounded 7 Figure 5 V vs. I Characteristic Requirements.8 Figure 6 Off-Hook Resistance test setup 9 Figure 7 Open Switch Interval test setup10 Figure 8 dc Current during Ringing Requirements 12 Figure 9 dc Current during Ringing test setup12 Figure 10 Metallic Impedance Du

34、ring Ringing Requirements.13 Figure 11 Metallic Impedance test setup 13 Figure 12 Longitudinal Impedance test setup.14 Figure 13 On-Hook Metallic Impedance Requirements.16 Figure 14 In-Band On-Hook Metallic Impedance (200 to 3200 Hz) Requirements 17 Figure 15 Return Loss Requirements .18 Figure 16 R

35、eturn Loss Test Circuit 19 Figure 17 Longitudinal Balance requirements20 Figure C.1 Example Longitudinal Balance Test Setup.23 Table of Tables Table 1 On-Hook Resistance Test Matrix 7 Table 2 Off-Hook Resistance Test Matrix9 Table 3 Simulated Ringing Test Signal Matrix 11 Table 4 ac Power Induction

36、Test Signal Matrix .15 Table 5 5 Hz to 200 Hz On-Hook Metallic Impedance Test Signal Matrix .16 Table 6 In-Band On-Hook Metallic Impedance Test Signal Matrix 17 Table A.1 Scaled On-Hook Performance From Recommended Limits .21 Table B.1 ISO R-40 Frequencies22 Copyright Telecommunications Industry Ass

37、ociation Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C 1 1 SCOPE This standard establishes criteria and procedures for evaluating the Resistance and Impedance performance of analog telephones and terminals conne

38、cted to the Public Switched Telephone Network (PSTN). The recommended on-hook requirements are written with a model of five (5) Customer Premise Equipment (CPE) attached to the Customer Interface (CI) and the minimum performance requirements are based on a model of three (3) CPE. This document propo

39、ses or references at least one measurement procedure for each technical requirement. However, these procedures are not exclusive. Any measurement procedure and equipment that can result in an identical measurement is considered valid. While the procedures may call out specific test points within the

40、 requirements, the full range of the requirements take precedent over the test method. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C 2 2 REFERENCES The following

41、 standards contain provisions, which, through reference in this text, constitute provisions of this Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possi

42、bility of applying the most recent editions of the standards indicated below. ANSI and TIA maintain registers of currently valid national standards published by them. 2.1 NORMATIVE REFERENCES 1. ANSI/TIA-968-A-2002, Telecommunications Telephone Terminal Equipment Technical Requirements for Connectio

43、n of Terminal Equipment to the Telephone Network. 2.2 INFORMATIVE REFERENCES 1. ANSI T1.401-2000, Network-to-Customer Installation Interfaces Analog Voicegrade Switched Access Lines Using Loop-Start and Ground-Start Signaling. Copyright Telecommunications Industry Association Provided by IHS under l

44、icense with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-470.210-C 3 3 ABBREVIATIONS, ACRONYMS, AND DEFINITIONS 3.1 ABBREVIATIONS AND ACRONYMS For the purposes of this Standard, the following abbreviations and acronyms apply. AWG American Wire Gauge CI Cu

45、stomer Interface CO Central Office (Used broadly to describe the telephone switch connected to a subscribers line) CPE Customer Premises Equipment ERL Echo Return Loss KSU Key System Unit RL Return Loss OSI Open Switch Interval 3.2 DEFINITIONS For the purposes of this Standard, the following definit

46、ions apply. Echo Return Loss The return loss averaged with 1/f power weighting over the log frequency band 500 Hz to 2500 Hz. Line Idle: A state of the CPE line when all connected CPE are On-Hook. Line In-Use: A state of the CPE line when at least one CPE is Off-Hook. Line State: The condition of the Tip and Ring interface. It can be ei