SMPTE RP 56-2002 Safe Action and Safe Title Areas for 8-mm Release Prints《8 mm发行拷贝的动作安全区和字幕安全区》.pdf

《SMPTE RP 56-2002 Safe Action and Safe Title Areas for 8-mm Release Prints《8 mm发行拷贝的动作安全区和字幕安全区》.pdf》由会员分享，可在线阅读，更多相关《SMPTE RP 56-2002 Safe Action and Safe Title Areas for 8-mm Release Prints《8 mm发行拷贝的动作安全区和字幕安全区》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、SMPTE RECOMMENDED PRACTICE RP 56-2002 Revision of RP 56-1995 Safe Action and Safe Title Areas for 8-mm Release Prints Page 1 of 3 pages Introduction Early in the development of the 8-mm type S program, it was recognized that the format would be used both for direct front and rear projection system.

2、Some committee members were concerned that the usable projectable image area might be different without specific standards for the two systems. It was, therefore, decided that it would benefit producers and laboratories if safe areas were developed for the 8-mm type S and 8-mm type R formats. This c

3、oncept became more important as the image area documents changed from the concept of specifically defined areas with tolerances for size and positioning to the internationally agreed to system of developing a minimum camera area and a maximum projectable image area. When the minimum and maximum area

4、 concept was accepted, the restatement of the positioning tolerances for the width caused a slight change such that the precise ideal format of 4:3 was lost in most cases. However, during the development of the initial committee document, it was recognized that there may be future application of the

5、 8-mm type S system in television. Therefore, the need to maintain a precise 4:3 format fortelecine use is significant. To derive the most useful areas, the committee proposes to utilize the standardized maximum projectable image area height for each format as the basis for all measurements. For cla

6、rity and ease of understanding, a value of 100% for both the height and width has been established as shown in figure 1. Because an ideal format does not exist, the 100% image area height is established as the basic parameter and the 100% width is derived by a ratio multiplication of 4:3 times the h

7、eight. All other values shown in the table are percentage ratios with the exception of those in the last column, which are derived from the related American National Standards (see annex A). By applying the above principle, the document achieves maximum usefulness while losing only 2% of the standar

8、dized width which can, when needed, be available for direct projection application. 1 Scope 1.1 This practice specifies the dimensions of the nominal safe action and safe title image areas for 8-mm release prints. lhe information provided applies to the use of these prints by either direct front or

9、rear screen projection. 1.2 The specifications are also applicable to reversal original photography. 2 Definitions 2.1 The safe action image area is the area within which all significant action should take place to ensure visibility of the action in the usual projection situation. 2.2 The safe title

10、 image area is the area within which the graphic information (e.g., titles, credits, tabulations, etc.) must be confined to prevent loss of this information (cropping) in the usual projection situation. Copyright O 2002 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave W

11、hite Plains, NY 10607 (914) 761-1100 Approved July 26,2002 RP 56-2002 T 100% 3 Specifications 3.1 The dimensions shall be as given in figure 1 and table 1. 3.2 For convenience, the dimensions are also expressed as a percentage of the nominal maximum projection image height and width. 3.3 The safe ac

12、tion and safe title areas are nominally centered within the maximum projectable image area. 3.4 The dimensions of image areas are derived from the standards listed in annex A. 3.5 A format ratio of 4:3 is maintained for all areas. The maximum projectable image height is considered as the basic param

13、eter for each format. NOTE - Safe areas are centered. True centers for all areas are established by an intersection of cornerconnecting diagonal lines. Figure 1 - Maximum projectable image area Table 1 - Dimensions Maxi mum Minimum projectable area Safe action area Safe title area camera image area

14、in mm in mm in mm in mm 8-mm type S Height 0.158 4.01 O. 142 3.61 0.126 3.20 0.1 63 4.14 Width 0.21 1 5.36 0.190 4.83 O. 169 4.29 0.224 5.69 8-mm type R Height O. 130 3.30 0.117 2.97 O. 104 2.64 0.143 3.63 Width 0.173 4.39 O. 156 3.96 0.138 3.51 0.1 84 4.67 Page 2 of 3 pages RP 56-2002 Annex A (info

15、rmative) Bibliography ANSIISMPTE 154-1998, Motion-Picture Film (8-mm Type S) - Projectable Image Area and Projector Usage ANSIISMPTE 234-1998, Motion-Picture Film (8-mm Type R) - Projectable Image Area and Projector Usage SMPTE 157-1999, Motion-Picture Film (8-mm Type S) - Camera Aperture Image and Usage SMPTE 231-1999, Motion-Picture Film (8-mm Type R) - Camera Aperture Image and Usage Page 3 of 3 pages