SANS 51395-3-2009 Thermal spraying - Acceptance inspection of thermal spraying equipment Part 3 Arc spraying《热喷涂 热喷涂设备验收检查 第3部分 电弧喷涂》.pdf

《SANS 51395-3-2009 Thermal spraying - Acceptance inspection of thermal spraying equipment Part 3 Arc spraying《热喷涂 热喷涂设备验收检查 第3部分 电弧喷涂》.pdf》由会员分享，可在线阅读，更多相关《SANS 51395-3-2009 Thermal spraying - Acceptance inspection of thermal spraying equipment Part 3 Arc spraying《热喷涂 热喷涂设备验收检查 第3部分 电弧喷涂》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22403-5 SANS 51395-3:2009 Edition 1 EN 1395-3:2007 Edition 1SOUTH AFRICAN NATIONAL STANDARD Thermal spraying Acceptance inspection of ther

4、mal spraying equipment Part 3: Arc spraying This national standard is the identical implementation of EN 1395-3:2007 and is adopted with the permission of CEN, rue de Strassart 36, B-1050 Brussels. WARNING Can only be used in conjunction with SANS 51395-1. Published by SABS Standards Division 1 Dr L

5、ategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 51395-3:2009 Edition 1 EN 1395-3:2007 Edition 1 Table of changes Change No.

6、 Date Scope National foreword This South African standard was approved by National Committee SABS TC 107, Metallic and other inorganic coatings, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in Apri

7、l 2009. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN13953 January2007 ICS25.220.20 SupersedesEN1395:1996 EnglishVersion ThermalsprayingAcceptanceinspectionofthermalspraying equipmentPart3:Arc

8、spraying ProjectionthermiqueContrledacceptationdumatriel deprojectionthermiquePartie3:Projectionlarc ThermischesSpritzenAbnahmeprfungenfrAnlagen zumthermischenSpritzenTeil3:Lichtbogenspritzen ThisEuropeanStandardwasapprovedbyCENon23December2006. CENmembersareboundtocomplywiththeCEN/CENELECInternalRe

9、gulationswhichstipulatetheconditionsforgivingthisEuropean Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcerningsuchnational standardsmaybeobtainedonapplicationtotheCENManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialver

10、sions(English,French,German).Aversioninanyotherlanguagemadebytranslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCENManagementCentrehasthesamestatusasthe officialversions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Bulgaria,Cyprus,CzechRepublic,Denmark,Eston

11、ia,Finland, France,Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Romania,Slovakia,Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG Manage

12、mentCentre:ruedeStassart,36B1050Brussels 2007CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN13953:2007:EThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 2 Contents Page Forew

13、ord3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principles of acceptance inspection4 5 Procedure of acceptance inspection.5 6 Designation 5 7 Inspection report5 Annex A (informative) Inspection report for arc spraying equipment (initial test/retest)6 Bibliography 8 This standard

14、 may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 3 Foreword This document (EN 1395-3:2007) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN. This

15、 European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2007, and conflicting national standards shall be withdrawn at the latest by July 2007. This document together with EN 1395-1, 1395-2, 1395-4, 1395

16、-5, 1395-6 and 1395-7 supersedes EN 1395:1996. EN 1395 consists of the following Parts, under the general title Thermal spraying Acceptance inspection of thermal spraying equipment: Part 1: General requirements; Part 2: Flame spraying including HVOF; Part 3: Arc spraying; Part 4: Plasma spraying; Pa

17、rt 5: Plasma spraying in chambers; Part 6: Manipulator systems; Part 7: Powder feed systems. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Rep

18、ublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. This standard may only be used and printed by approved

19、 subscription and freemailing clients of the SABS. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 4 1 Scope This European Standard specifies requirements for the acceptance inspection of thermal spraying equipment, in this c

20、ase arc spraying, used to produce thermally sprayed coatings of reproducible quality. This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures. 2 Normative references The following referenced documents are indispensable for the applic

21、ation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 657:2005, Thermal spraying Terminology, classification EN ISO 14919:2001, Thermal spraying Wires, rods and cords

22、for flame and arc spraying Classification Technical supply conditions (ISO 14919:2001) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 apply. 4 Principles of acceptance inspection 4.1 General The following clauses reveal state of the art tech

23、nology in thermal spraying equipment and the minimum requirements concerning a stable parameter setting and maintenance as given in Annex A. 4.2 Atomising gas The atomising gas hoses and the control device shall be designed in such a manner that an undisturbed operation is ensured. 4.3 Arc spraying

24、nozzle The nozzle system (contact tubes and air nozzle) shall permit a constant arc to be maintained and provide atomisation without causing deposits that might disturb the operation. 4.4 Spraying wire feed unit A continuously controllable and reproducible feed of the wires shall be provided. A prec

25、ondition for this is an adequate constant air pressure and supply of electrical power. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 5 5 Procedure of acceptance inspection 5.1 General Spraying equipment shall be deemed to h

26、ave been properly supplied for all suitable spraying applications and for use with all suitable spraying materials required for the spraying process if it complies with the following requirements: 5.2 Electrical power and wire feed unit Proof of the power rating required for continuous operation and

27、 of compliance of the feed unit with the requirements as specified in 4.4 shall be deemed to have been provided if: no deviations of the adjusted electrical values of more than 5 % or other disturbances due to an increased thermal loading occur; and system is operating at a maximum capacity for 10 m

28、in with a coating material with a suitable diameter: 1) anti-corrosion arc spraying system: zinc aluminium alloy, thermal spray material according to EN ISO 14919:2001, 2.3, or 2) engineering application arc spraying system: pure copper, thermal spray material according to EN ISO 14919:2001, 4.1. 5.

29、3 Atomising gas The equipment shall be deemed to comply with the requirements of 4.2 if the atomising gas pressure indication does not deviate by more than 5 % from the set point over a 10 min period of spraying. 5.4 Arc spraying nozzle The nozzle system shall be deemed to comply with the requiremen

30、ts given in 4.3 if, after testing according to 4.4, no disturbances occur in the arc and no disturbing deposits have been built up on the nozzle system by more or less molten spraying material. 6 Designation Acceptance inspection of the thermal spraying equipment for arc spraying shall be designated

31、 as follows: Acceptance inspection according to EN 1395-3. 7 Inspection report An example for the inspection report is given in Annex A. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 6 Annex A (informative) Inspection repor

32、t for arc spraying equipment (initial test/retest) The initial test/retest fulfils the requirements of the acceptance inspection according to EN 1395-3. User:. Manufacturer:. Year of manufacture: . Type of equipment: Type of spraying gun: . Spraying wire used for testing . Diameter: mm CE-documentat

33、ion complete: yes / no Change after 10 minute continuous testing Evaluation actual value Item tested, where applicable Full scale Set point min. max. maximum deviation in % Limit in % passed failed Current A 5 Electrical power Voltage V 5 Pressure bar 5 Atomising gas Flow Nl/min 1 ) 5 Wire feed Spee

34、d m/min 5 Flow l/min 10 Cooling water temperature to spraying gun C 10 C 1)Referred to temperature 0 C and normal pressure (1 013,25 hPa). This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007 (E) 7 Deposits: yes / no Nozzle disturbanc

35、e: yes / no Time needed for stabilisation: . Automatic energy shutdown: Lack of gas: yes / no Lack of cooling water: yes / no Excessive variations in feed: yes / no Limits of error of measuring instruments: % of set point (max. 5 %) Class 2,5 2) : yes / no Comments: . The thermal spraying equipment

36、has been accepted: yes / no Date: Inspectors signature: Date: Customers signature:. Date: Suppliers signature: 2)Maximum permissible error expressed by percentage of measuring span. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 1395-3:2007

37、 (E) 8 Bibliography 1 EN 1395-1, Thermal spraying Acceptance inspection of thermal spraying equipment Part 1: General requirements SABSThis standard may only be used and printed by approved subscription and freemailing clients of the SABS. This page has been left blank intentionally This standard ma

38、y only be used and printed by approved subscription and freemailing clients of the SABS. SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of

39、2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensure that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and wo

40、uld therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual noti

41、fication service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and intern

42、ational standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Inform

43、ation Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive no

44、tification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Un

45、less exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary deta

46、ils such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za This standard may only be used and printed by approved subscription and freemailing clients of the SABS.