SANS 1183-2008 Nurses- woven uniform fabric (polyester-and-cotton)《护士用机织制服衣料(聚酯纤维和棉纤维)》.pdf

《SANS 1183-2008 Nurses- woven uniform fabric (polyester-and-cotton)《护士用机织制服衣料(聚酯纤维和棉纤维)》.pdf》由会员分享，可在线阅读，更多相关《SANS 1183-2008 Nurses- woven uniform fabric (polyester-and-cotton)《护士用机织制服衣料(聚酯纤维和棉纤维)》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21218-6 SANS 1183:2008Edition 2.1SOUTH AFRICAN NATIONAL STANDARD Nurses woven uniform fabric (polyester-and-cotton) Published by Standards

4、 South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 1183:2008 Edition 2.1 Table of changes Change No. Date Scope Amdt 1 2008 Amended to update referenced standards. Forew

5、ord This South African standard was approved by National Committee StanSA SC 5110.01B, Textiles Woven fabrics, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in June 2008. This document supersedes SANS 1183:20

6、07 (edition 2). A vertical line in the margin shows where the text has been technically modified by amendment No. 1. Annex A forms an integral part of this standard. Annexes B and C are for information only. SANS 1183:2008 Edition 2.1 1 Contents Page Foreword 1 Scope . 3 2 Normative references . 3 3

7、 Terms and definitions . 4 4 Requirements . 4 5 Sampling and compliance with the standard . 6 6 Inspection and methods of test 7 6.1 Inspection 7 6.2 Conditioning 7 6.3 Fibre composition 7 6.4 Weave . 7 6.5 Mass per area . 7 6.6 Number of threads per centimetre 7 6.7 Breaking strength 7 6.8 Resistan

8、ce to pilling 8 6.9 Recovery from creasing 8 6.10 Non-fibrous material content . 8 6.11 Dimensional changes on laundering . 8 7 Packing, labelling and marking 8 Annex A (normative) Notes to purchasers . 9 Annex B (informative) Recommended yarn linear densities 10 Annex C (informative) Quality verifi

9、cation of nurses woven uniform fabric . 10 Bibliography 10 SANS 1183:2008 Edition 2.1 2 This page is intentionally left blank SANS 1183:2008 Edition 2.1 3 Nurses woven uniform fabric (polyester-and-cotton) 1 Scope This standard specifies requirements for two types of polyester-and-cotton fabric suit

10、able for nurses uniforms. 2 Normative references The following referenced documents are indispensable for the application of this document. All normative documents are subject to revision and, since any reference to a normative document is deemed to be a reference to the latest edition of that docum

11、ent, parties to agreements based on this document are encouraged to take steps to ensure the use of the most recent editions of the normative documents indicated below. Information on currently valid national and international standards can be obtained from Standards South Africa. SANS 70, Condition

12、ing of textiles and standard temperate atmosphere for determining their physical and mechanical properties. SANS 79, Textiles Mass per unit area of conditioned fabrics. SANS 82, Width of a textile fabric in a piece or roll. SANS 84, Length of fabric in a piece or roll. SANS 960:2005, Textiles Dimens

13、ional stability during washing and drying procedures. SANS 977, Textile tolerances. SANS 1270, General requirements for woven textile piece-goods and household articles. SANS 1833-1/ISO 1833-1, Textiles Quantitative chemical analysis Part 1: General principles of testing. SANS 1833-11/ISO 1833-11, T

14、extiles Quantitative chemical analysis Part 11: Mixtures of cellulose and polyester fibres (method using sulfuric acid). SANS 2313/ISO 2313, Textile fabrics Determination of recovery from creasing of a horizontally folded specimen by measuring the angle of recovery. Amdt 1 SANS 5091, Bow and skewnes

15、s in woven textile fabrics. SANS 1183:2008 Edition 2.1 4 SANS 5114, Non-fibrous material content of textiles (method using starch-digesting enzymes). SANS 5272, Non-fibrous material content of textiles Hydrochloric acid method. SANS 5402 (SABS SM 402), Fabric recovery from creasing: angle of recover

16、y method. Amdt 1 SANS 6116, Resistance of textile fabrics to pilling and fuzzing (Random tumble method). SANS 7211-2/ISO 7211-2, Textiles Woven fabrics Construction Methods of analysis Part 2: Determination of number of threads per unit length. SANS 10004, Terms and definitions for textiles and text

17、ile merchandise. SANS 10076-1, The assessment of defects in textile piece-goods and made-up articles Part 1: Defects in woven piece-goods (cellulosic and cellulosic blends). SANS 10153, The labelling and marking of textiles and household textile articles. SANS 11108 (SABS SM 1108:1990), Washing pret

18、reatment of textile fabrics. SANS 13934-1/ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elongation at maximum force using the strip method. 3 Terms and definitions For the purposes of this document, the terms and definitions given in SANS 10004 and th

19、e following apply. 3.1 acceptable acceptable to the authority administering this standard, or to the parties concluding the purchase contract, as relevant 3.2 lot not less than 20 and not more than 300 pieces of fabric of the same type and width, woven on the same type of loom, made by one manufactu

20、rer, and submitted at any one time for inspection and testing 4 Requirements 4.1 General Nurses woven uniform fabric shall be a) uniformly made in accordance with sound manufacturing practice from clean blended yarns (see 6.1.1), b) of the required type (see table 1 and annex A), c) bleached to an a

21、cceptable white and be singed and heat-set (see 6.1.1 and annex A), and d) delivered in a clean and commercially dry condition (see 6.1.1). SANS 1183:2008 Edition 2.1 5 4.2 Colour and colour match The colour of the nurses woven uniform fabric (see 6.1.1) shall be an acceptable match, in terms of SAN

22、S 10076-1, to the bleached white required (see annex A). 4.3 Selvedges The selvedges (see 6.1.1) shall comply with the relevant requirements given in SANS 1270. 4.4 Width The width (between selvedges) of nurses woven uniform fabric, when measured in accordance with 6.1.2, subject to the relevant tol

23、erances given in SANS 977, shall be 115 cm or 150 cm, as required (see annex A). 4.5 Piece length Unless otherwise required (see annex A), the length of each piece, when measured in accordance with 6.1.2, shall be at least 55 m, subject to the relevant tolerances given in SANS 977. 4.6 Bow and skewn

24、ess of weft The mean bow and the mean skewness of the weft, when measured in accordance with 6.1.2, shall not, in either case, exceed 3 %, and neither the bow nor the skewness shall, at any part of the fabric, exceed 7 %. 4.7 Fibre composition When determined in accordance with 6.3, the fibre compos

25、ition of the nurses woven uniform fabric shall comply with the relevant requirements given in table 1. 4.8 Weave The weave of the nurses woven uniform fabric, when visually examined in accordance with 6.1.1, and determined in accordance with 6.4, shall be as given in table 1, appropriate to the type

26、 of fabric required. 4.9 Fabric When tested in accordance with 6.5 to 6.11 (inclusive), the finished nurses woven uniform fabric shall comply with the requirements given in table 1, appropriate to the type. 4.10 Freedom from defects The assessment and stringing of defects, and the deductions to be m

27、ade for strung and unstrung defects, shall be in accordance with SANS 10076-1, and shall be based on the following LAQs: a) for pieces: 10; and b) for a lot: 8. SANS 1183:2008 Edition 2.1 6 Table 1 Fabric requirements 1 2 3 4 RequirementTypea Property N65 N69 Test method subclause Fibre composition,

28、 % Polyester .Cotton 50 3 50 3 65 3 35 3 6.3 Weave . Plain 2/1 twill 6.4 Mass per area (free from non-fibrous material), g/m2, min. 160 180 6.5 Number of threads per cm bWarp, min. .Weft c.40 2545 246.6 Breaking strength, N, min. Warp Weft .800 300 900 400 6.7 Resistance to pillingd, rating, min. .

29、3-4 (i.e. slight to moderate) 6.8 Recovery from creasing, degrees, min. 120 6.9 Non-fibrous material content, %, max. 6 6.10 Dimensional changes on laundering, %, max. Warp and weft .2 6.11 aThe type number is derived from the sum of the number of warp threads and weft threads per centimetre. Design

30、ation by the type number is restricted to fabrics that comply with the above requirements. bRecommended yarn linear densities are given in annex B. cSubject to a tolerance of 10 %. dWash test specimens in accordance with SANS 11108:1990, procedure A, before testing. 5 Sampling and compliance with th

31、e standard 5.1 General This clause applies to the sampling for inspection and testing before acceptance or rejection of single lots (consignments) when no information about the implementation of quality control or testing during manufacture is available to help in assessing the quality of the lot. I

32、t is also used as the procedure for adjudicating in cases of dispute. Information on the quality verification of nurses woven uniform fabric is given in annex C. 5.2 Sampling 5.2.1 General The following sampling procedure shall be applied (after the lot has been checked for compliance with clause 7)

33、 to determine whether the lot complies with the remaining requirements of the standard, and the sample for inspection so taken shall be deemed to be representative of the lot. SANS 1183:2008 Edition 2.1 7 5.2.2 Sample for inspection From the lot, take at random 30 pieces or all the pieces (whichever

34、 is less) as the sample for inspection. 5.2.3 Laboratory samples for testing From the lot, or from the sample taken in accordance with 5.2.2, take at random five pieces. From each of the five pieces and from a position taken at random, but at least 3 m from an end of the piece, cut a full-width labo

35、ratory sample of area at least 2 m2. 5.3 Compliance The lot shall be deemed to comply with the requirements of the standard if, after inspection and testing of the laboratory samples taken in accordance with 5.2.3, the laboratory samples are found to comply with all the requirements of the standard.

36、 6 Inspection and methods of test 6.1 Inspection 6.1.1 Divide the number of pieces taken in accordance with 5.2.2 into two equal sets. Visually examine the first set for compliance with the requirements given in 4.1, 4.2, 4.3, 4.8 and 4.10. 6.1.2 Measure each piece in the second set for compliance w

37、ith the requirements given in 4.4, 4.5 and 4.6, using SANS 82, SANS 84 and SANS 5091 to measure the width, the length, and the bow and skewness of the weft respectively. 6.2 Conditioning Condition each laboratory sample (see 5.2.3) in accordance with SANS 70 and then cut from each the test specimens

38、 required for the tests given in 6.3 to 6.11 (inclusive). 6.3 Fibre composition Use SANS 1833-1 and SANS 1833-11. Check for compliance with the relevant requirements of table 1. 6.4 Weave Use visual examination (see 6.1.1) and physical analysis. Check for compliance with the relevant requirements of

39、 table 1. 6.5 Mass per area Use SANS 79. Check for compliance with the relevant requirements of table 1. 6.6 Number of threads per centimetre Use SANS 7211-2. Check for compliance with the relevant requirements of table 1. 6.7 Breaking strength Use SANS 13934-1. Check for compliance with the relevan

40、t requirements of table 1. SANS 1183:2008 Edition 2.1 8 6.8 Resistance to pilling Use SANS 6116. Wash the test specimens in accordance with SANS 11108:1990, procedure A, before testing them. Check for compliance with the relevant requirement of table 1. 6.9 Recovery from creasing Use SANS 2313. Chec

41、k for compliance with the relevant requirement of table 1. Amdt 1 6.10 Non-fibrous material content Use SANS 5114 and SANS 5272. Check for compliance with the relevant requirement of table 1. 6.11 Dimensional changes on laundering Use SANS 960:2005, washing procedure A1, drying procedure E. Check fo

42、r compliance with the relevant requirement of table 1. 7 Packing, labelling and marking 7.1 Packing 7.1.1 Unless otherwise required (see annex A), each piece shall be rolled full-width (i.e. unfolded) and face inward on a tube. 7.1.2 Only pieces of the same type and width shall be packed together in

43、 a bulk container. 7.2 Labelling and marking Pieces and bulk containers shall be labelled and marked in accordance with SANS 10153. 7.3 Additional marking When so required (see annex A), pieces or bulk containers (or both) shall bear information additional to that specified in 7.2. SANS 1183:2008 Ed

44、ition 2.1 9 Annex A (normative) Notes to purchasers A.1 In addition to data clearly describing the nurses woven uniform fabric ordered, the following requirements shall be specified in tender invitations and in each order or contract: a) the type (see 4.1); b) the colour of the bleached white fabric

45、 required (see 4.2); c) the width (see 4.4); d) the piece length, if other than as specified (see 4.5); e) the method of packing, if other than as specified (see 7.1.1); and f) additional marking, if required (see 7.3). A.2 The order or contract that specifies the requirements listed in A.1 shall be

46、 made available to inspection representatives for inspection purposes when so required. SANS 1183:2008 Edition 2.1 10 Annex B (informative) Recommended yarn linear densities Recommended yarn linear densities for nurses woven uniform fabric that complies with the requirements of this standard are giv

47、en in table B.1. Table B.1 Recommended yarn linear densities 1 2 3 Tex Type Warp Weft N65 14 x 2 17 N69 25 25 Annex C (informative) Quality verification of nurses woven uniform fabric When a purchaser requires ongoing verification of the quality of nurses woven uniform fabric, it is suggested that,

48、instead of concentrating solely on evaluation of the final product, he also direct his attention to the manufacturers quality system. In this connection it should be noted that SANS 9001 covers the provisions of an integrated quality system. Bibliography SANS 9001/ISO 9001, Quality management systems Requirements. Standards South Africa