SAE J 852-2009 Front Cornering Lamps for Use on Motor Vehicles《用于机动车辆的前拐弯灯》.pdf

《SAE J 852-2009 Front Cornering Lamps for Use on Motor Vehicles《用于机动车辆的前拐弯灯》.pdf》由会员分享，可在线阅读，更多相关《SAE J 852-2009 Front Cornering Lamps for Use on Motor Vehicles《用于机动车辆的前拐弯灯》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2009 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)

4、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SURFACE VEHICLE RECOMMENDED PRACTICE J852 MAR2009 Issued 1963-04 Revised 2009-03 Superseding J852 APR2001 Front Cornering Lamps for Use on Motor Vehicles RATIONALE This document was revised to incorporate changes to

5、the new more user-friendly photometry format balloted and approved in June 2006. There are no photometry requirements changes to this document. The current Table 1, Photometry Requirements is replaced with Figure 1, Photometry Requirements and current Figure 1, Test Point Orientation is changed to F

6、igure 2. Corresponding references to them in paragraph 6.1.5 are also changed. In the new Figure 1 the area defined by: 10U to 90U45L to 45R is now identified as Zone 1 and the Note 2 scan is shown as “A scan shall be performed in 1-degree increments both horizontally and vertically. If any point ex

7、ceeds 125 cd during the scan, a maximum of 500 cd is permissible if contained within a 2 degree conical angle.” which is the same procedure as currently in SAE J583 Front Fog Lamp. Also, the 4U, 2U, 1U and H45L to 85R are identified as Lines 1, 2, 3 and 4 respectively and Note 3 states: “All-line sc

8、ans are to be performed an lines 1, 2, 3 and 4 for maximum cd,” which is also the same note as used in SAE J583. 1. SCOPE This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for front cornering lamps intended for use on motor vehicles. 2. REFERENCES 2.1 A

9、pplicable Publications The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001

10、, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J567 Lamp Bulb Retention System SAE J575 Test Methods and Equipment for Lighting Devices and Components for Use on Vehicles Less than 2032 mm in Overall Width SAE J576 Plastic Material or Materials for Use in

11、 Optical Parts Such as Lenses and Reflex Reflectors of Motor Vehicle Lighting Devices SAE J578 Color Specification SAE J759 Lighting Identification Code Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-

12、,-SAE J852 Revised MAR2009 Page 2 of 5 3. DEFINITIONS 3.1 Front Cornering Lamps Steady burning lamps used in conjunction with the turn signal system to supplement the headlamps by providing additional illumination in the direction of turn. They may be used independent of the turn signal to ease mane

13、uvering at very low speeds. 4. IDENTIFICATION CODE DESIGNATION Front cornering lamps meeting the performance requirements of this document may be identified by the code K in accordance with SAE J759. 5. TESTS 5.1 SAE J575 is a part of this document. The following tests are applicable with the modifi

14、cations as indicated. 5.1.1 Vibration Test 5.1.2 Moisture Test 5.1.3 Dust Exposure Test 5.1.4 Corrosion Test 5.1.5 Photometry Test In addition to the test procedures in SAE J575, the following apply: 5.1.5.1 Photometry measurements shall be made with the light source of the lamp at least 3 m from th

15、e photometer. The H-V axis shall be taken as the horizontal line through the light source and perpendicular to the longitudinal axis of the vehicle. 5.1.6 Warpage Test on Device with Plastic Components 5.2 Color Test SAE J578 is a part of this document. 5.3 Plastic Materials SAE J576 is a part of th

16、is document. 6. REQUIREMENTS 6.1 Performance Requirements A device tested in accordance with the test procedure specified in Section 5 shall meet the following requirements: 6.1.1 Vibration SAE J575. 6.1.2 Moisture SAE J575. Copyright SAE International Provided by IHS under license with SAENot for R

17、esaleNo reproduction or networking permitted without license from IHS-,-,-SAE J852 Revised MAR2009 Page 3 of 5 6.1.3 Dust Exposure SAE J575. 6.1.4 Corrosion SAE J575. 6.1.5 Photometry SAE J575. The lamp shall be designed to conform to the photometry requirements contained in Figure 1. NOTE: Test poi

18、nts shown are for a lamp mounted on the left side of the vehicle L and R designations in Figure 1 should be reversed for a lamp mounted on the right side of the vehicle. Refer to Figure 2 for Test Point Orientation. 6.1.6 Warpage SAE J575. 6.1.7 Color Requirements The color of the light from a front

19、 cornering lamp shall be white to yellow as specified in SAE J578. 6.2 Material Requirements Plastic materials used in optical parts shall meet the requirements of SAE J576. 7. GUIDELINES The following guidelines apply to front cornering lamps as used on motor vehicles and should not be considered p

20、art of the requirements. 7.1 The front cornering lamps are intended for use only when the headlamps are operational. 7.2 Cornering lamp activation should coincide with turn signal activation to provide illumination in the direction of the intended turn. 7.3 Cornering lamps may be deactivated at high

21、 vehicle speed (lane change maneuver) or while stopped, to avoid discomfort to other road users. 7.4 Cornering lamp may be activated by steering angle. 7.5 Location Requirements The mounting height of the front cornering lamps shall be from 305 mm to 760 mm above the ground as measured from the opti

22、cal center of the lamp on an unloaded vehicle. 7.6 For requirements and gauges to be used in socket designs, refer to SAE J567. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J852 Revised MAR200

23、9 Page 4 of 5 FIGURE 1 - PHOTOMETRIC REQUIREMENTS LUMINOUS INTENSITY (cd) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J852 Revised MAR2009 Page 5 of 5 FIGURE 2 - TEST POINT ORIENTATION 8. NOT

24、ES 8.1 Marginal Indicia A change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revis

25、ion of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE FRONT CORNERING LAMP TASK FORCE OF THE SAE SIGNAL AND MARKING DEVICES COMMITTEE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-