SAE AS 5169A-2009 FITTING PORT PLUG AND BLEEDER《舱门插头和泄放阀配件》.pdf

《SAE AS 5169A-2009 FITTING PORT PLUG AND BLEEDER《舱门插头和泄放阀配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5169A-2009 FITTING PORT PLUG AND BLEEDER《舱门插头和泄放阀配件》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, PORT PLUG AND BLEEDER AS5169Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, witho

2、ut the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REAFFIRMED 2005-06 REVISED 2009-11THIRD ANGLE PROJECTION CU

3、STODIAN: SAE G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730 AS5169 SHEET 1 OF 5 REV. A PROCUREMENT SPECIFICATION: /4/ AS4875SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, a

4、ndits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsugg

5、estions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5169ARATIONALE 1. UPDATED QML STATEMENT AND SPECIFICATION NUMBERS 2. ADDED CADMIUM NOTICE 3. ADDED NOTE /19/ INACTIVE MATERIAL NOTES AND DATES 4. ADDED S MATERIAL NOTE /1

6、/ FIGURE 1 - FITTING, PORT PLUG AEROSPACE STANDARD AS5169 SHEET 2 OF 5 REV. A FITTING, PORT PLUG AND BLEEDER TABLE 1A - DIMENSIONS BASIC NO. AS5169 /14/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A A B .010 C +.000/-.016 D .005 E .031 F 02 .125 .3125-24 UNJF .547 .542 .266 .062 .156 .0

7、05 03 .188 .3750-24 UNJF .562 .605 .266 .125 .156 .005 04 .250 .4375-20 UNJF .625 .668 .312 .171 .188 .005 05 .312 .5000-20 UNJF .625 .730 .281 .234 .188 .005 06 .375 .5625-18 UNJF .719 .792 .359 .296 .219 .005 08 .500 .7500-16 UNJF .781 .980 .359 .390 .250 .005 10 .625 .8750-14 UNJ .781 1.103 .328

8、.484 .312 .005 12 .750 1.0625-12 UNJ 1.000 1.353 .484 .609 .344 .008 16 1.000 1.3125-12 UNJ 1.000 1.603 .422 .843 .344 .008 20 1.250 1.6250-12 UNJ 1.000 1.853 .609 1.078 .344 .008 24 1.500 1.8750-12 UNJ 1.000 2.099 .609 1.312 .344 .008 28 1.750 2.2500-12 UNJ 1.000 2.474 .531 1.546 .344 .008 32 2.000

9、 2.5000-12 UNJ 1.000 2.724 .516 1.781 .344 .008 TABLE 1B - DIMENSIONS BASIC NO. AS5169 /14/ SIZE CODE G H J K M +.002/-.003 N S +.015/-.000 02 .109 .552 - 565 .219 .312 .250 .312 .063 03 .109 .615 - 628 .281 .328 .313 .375 .063 04 .109 .678 691 .344 .375 .364 .438 .075 05 .125 .740 - .753 .406 .375

10、.427 .500 .075 06 .125 .802 - .815 .469 .422 .482 .562 .083 08 .156 .990 1.003 .625 .469 .660 .750 .094 10 .156 1.113 1.128 .750 .531 .773 .875 .107 12 .188 1.363 1.380 .938 .594 .945 1.125 .125 16 .188 1.613 1.630 1.188 .594 1.195 1.375 .125 20 .234 1.863 1.880 1.500 .594 1.507 1.625 .125 24 .234 2

11、.109 2.135 1.719 .594 1.756 1.875 .125 28 .312 2.484 2.510 2.094 .594 2.131 2.250 .125 32 .328 2.734 2.760 2.344 .594 2.381 2.500 .125 INACTIVE IN PART /19/ AEROSPACE STANDARD AS5169 SHEET 3 OF 5 REV. A FITTING, PORT PLUG AND BLEEDER TABLE 1C - WEIGHTS BASIC NO. AS5169 /14/ SIZE CODE LB/EA APPROX RE

12、F AL LB/EA APPROX REF STEEL LB/EA APPROX REF TI 02 .00823 .02367 .01305 03 .0105 .03033 .01674 04 .0141 .0406 .0224 05 .0171 .0493 .0271 06 .0234 .0671 .0369 08 .0407 .117 .0646 10 .0493 .141 .0781 12 .099 .283 .156 16 .142 .407 .225 20 .181 .522 .288 24 .229 .658 .363 28 .343 .990 .544 32 .414 1.18

13、8 .657 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. DASH AS CODE LETTER - TYPE 4130 PER AMS-S-6758 OR AMS6370 OR TYPE 4140 PER AMS6349 OR AMS6382. /2/ AND /19/ b. CO

14、DE LETTER D - TYPE 2024-T6 OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 /19/. c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639. d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648. e. CODE LETTER R - TYPE 321 CORROSION

15、 RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645. f. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. g. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. h. CODE LETTER S TYPE 347 CORROSION RESISTANT STEEL BAR PER AMS-Q

16、Q-S-763, OR AMS5646. /2/ HEAT TREATMENT: a. DASH AS MATERIAL CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b. OTHER MATERIAL CODE LETTERS - NONE. AEROSPACE STANDARD AS5169 SHEET 4 OF 5 REV. A FITTING, PORT PLUG AND BLEEDER 3. FINISH: a. DASH AS MATERIAL CODE LETTER - CADMIUM

17、PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTER D 1. ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. D CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY

18、 WILL HAVE THE FINISH CODE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINSH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CLASS 3, TYPE II, WITH MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. SEE PROCUREMENT SPECIFICATION FOR ADD

19、ITIONAL REQUIREMENTS. c. MATERIAL CODE LETTERS J, K, R, AND S - PASSIVATE PER AMS 2700, TYPE 6 OR 7. d. MATERIAL CODE LETTER T - ANODIZE PER AMS2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 WITH COLOR PER PROCUREMENT SPECIFICATION. e. MATERIAL CODE LETTER W. 1. ANODIZE PER MIL-A-8625, TYPE

20、II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINSH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CLASS 3, TYPE II, WIT

21、H MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. SEE PROCUREMENT SPECIFICATION FOR ADDITIONAL REQUIREMENTS. /4/ PROCUREMENT SPECIFICATION: AS4875 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED

22、 MANUFACTURER LISTED IN THE NADCAP QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT . /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3 OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND

23、 MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS SHOWN IN TABLE 2: TABLE 2 - OPERATING PRESSURES FOR ASSOCIATED MATER

24、IAL SIZE MATERIAL PSI 02-08 ALUMINUM ALLOY 3000 10-16 ALUMINUM ALLOY 150020-28 ALUMINUM ALLOY 1000 32 ALUMINUM ALLOY 600 02-16 STEEL ALLOY 300020-32 STEEL ALLOY 1500 02-16 CORROSION RESISANT STEEL 3000 20-32 CORROSION RESISANT STEEL 1500 02-16 TITANIUM ALLOY 3000 20-32 TITANIU ALLOY 1500AEROSPACE ST

25、ANDARD AS5169 SHEET 5 OF 5 REV. A FITTING, PORT PLUG AND BLEEDER /7/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942. /8/ SUFFIX LETTER L - CODE L PARTS SHALL HAVE SAFETY WIRE HOLES AS SHOWN. 9. INTERPRETATION OF DRAWING PER ARP4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B4

26、6.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS

27、 .015, ANGULAR DIMENSIONS 030. /14/ EXAMPLE OF PART NUMBER: 15. THE CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE

28、 DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. /16/ THIS STANDARD MATES WITH PORT ENDS PER AS5202. 17 THIS STANDARD IS THE FUNCTIONAL EQUIVAL

29、ENT OF AN814 AND MS24391 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 18 TITANIUM AND CADMIUM SHALL NOT BE USED FOR OXGEN OR PORTABLE WATER SYSTEMS. /19/. INACTIVE MATERIAL CODES: a. PART NUMBERS WITH MATERIAL CODE LETTER D IS INACTIVE FOR NEW DESIGN AS OF 2009-02. USE PART NUMBERS WITH MATERIAL CODE LETTER W FOR NEW DESIGN. b. PART NUMBERS WITH MATERIAL CODE LETTER S IS INACTIVE FOR NEW DESIGN AS OF 2009-02. USE PART NUMBERS WITH MATERIAL CODE LETTER R FOR NEW DESIGN.