SAE AS 5167A-2003 FITTING ADAPTER FLARED AIR PRESSURE GAUGE《气压表扩口适配器接头》.pdf

《SAE AS 5167A-2003 FITTING ADAPTER FLARED AIR PRESSURE GAUGE《气压表扩口适配器接头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5167A-2003 FITTING ADAPTER FLARED AIR PRESSURE GAUGE《气压表扩口适配器接头》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, ADAPTER, FLARED, AIR PRESSURE GAUGE AS5167Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or ot

2、herwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REVISED 2003-08 REAFFIRMED 2015-04THIRD ANGLE

3、 PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS5167 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: /3/ AS4841SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvolunt

4、ary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwritte

5、ncomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5167A RATIONALE AS5167A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - FITTING, ADAPTERTABLE 1 - WEIGHTSBASIC NO.AS5167/1

6、2/SIZE CODE(NOMINALTUBE SIZE)PORT#1(NOMINALTUBE SIZE)PORT#2LB/EAMAXALLB/EAMAXTI0405 .250 .312 .0907 .144AEROSPACE STANDARD AS5167 SHEET 2 OF 2 REV. A FITTING, ADAPTER, FLARED, AIR PRESSURE GAUGE NOTES:/1/ MATERIAL:a. CODE LETTER D - TYPE 2024-T6 ALUMINUM ALLOY BAR PER QQ-A-225/6 OR AMS 4112 OR TYPE

7、2024-T851 ALUMINUM ALLOY BAR PER QQ-A-225/6.b. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS 4928.c. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124.2. FINISH:a. CODE LETTER D - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE

8、BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION.b. CODE LETTER T - ANODIZE PER AMS 2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS 2486 WITH COLOR PER PROCUREMENT SPECIFICATION.c. CODE LETTER W - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION./3/ PR

9、OCUREMENT SPECIFICATION: AS4841 EXCEPT AS SPECIFIED ON THIS STANDARD. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S) OR ACCREDITED DISTRIBUTOR(S) AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE PRODUCT./4/ IDENTI

10、FICATION AT LOCATION SHOWN: MARK MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND MATERIAL CODE LETTER PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, 15B.5. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH A MAXIMUM OPERATING PRESSURE OF 3000 psi. THIS STANDARD IS THE FUNCTIONAL E

11、QUIVALENT OF AN6285-2 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD./6/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942.7. INTERPRETATION OF DRAWING PER ARP4296.8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in

12、 Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra.9. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030./12/13. THE CHANGE BAR ( l ) LOCAED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.