SAE AS 5013-1997 FITTING ADAPTER STRAIGHT FLARELESS EXTERNAL SWAGE HYDRAULIC《液压外部铸模直线无扩口适配器配件》.pdf

《SAE AS 5013-1997 FITTING ADAPTER STRAIGHT FLARELESS EXTERNAL SWAGE HYDRAULIC《液压外部铸模直线无扩口适配器配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5013-1997 FITTING ADAPTER STRAIGHT FLARELESS EXTERNAL SWAGE HYDRAULIC《液压外部铸模直线无扩口适配器配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, ADAPTER, STRAIGHT FLARELESS, EXTERNAL SWAGE, HYDRAULIC AS5013Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin

2、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-11REAFFIRMED2015-04THIRD ANG

3、LE PROJECTION CUSTODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730AS5013 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: /5/ AS4459SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andi

4、ts applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments

5、andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5013 RATIONALE AS5013 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - UNION, EXTERNAL SWAGE TO FLARELESSTABLE 1A - DIMENSIONS A-GBAS

6、IC NO.AS5013/15/SIZE CODENOMINALTUBESIZEA.015 BC.015 DF+.000.015 G03 .188 1.318 .422 .625 .195/ .198 .750 .12504 .250 1.484 .453 .730 .257/ .260 .767 .15605 .312 1.528 .453 .760 .319/ .322 .810 .15606 .375 1.530 .469 .780 .382/ .385 .845 .17008 .500 2.332 .562 1.350 .508/ .511 1.350 .25010 .625 2.35

7、7 .625 1.350 .633/ .636 1.350 .25012 .750 2.460 .688 1.350 .758/ .761 1.460 .25016 1.000 2.858 .688 1.687 1.008/1.011 1.601 .26520 1.250 3.050 .688 1.750 1.258/1.262 1.795 .35024 1.500 2.905 .688 1.750 1.513/1.517 1.828 .150AEROSPACE STANDARD AS5013 SHEET 2 OF 3 FITTING, ADAPTER, STRAIGHT FLARELESS,

8、 EXTERNAL SWAGE, HYDRAULIC NOTES:/1/ MATERIAL:a. CODE LETTER “”: 21-6-9 CRES BAR PER AMS 5656b. CODE LETTER “E”: COMMERCIALLY PURE TITANIUM BAR PER AMS 4921c. CODE LETTER “D”: 6061T6 ALUMINUM ALLOY PER QQ-A-225/8/2/ FINISH:a. MATERIAL CODE “”: PASSIVATE PER QQ-P-35 TYPE VII, PTFE COAT (COLOR GREEN)

9、BORE DIAMETER TO “V” DEPTH, OVERSPRAY ON “Y” PERMISSIBLE.b. MATERIAL CODE “E”: PTFE COAT (COLOR BLACK) EXTERIOR SURFACES AND BORE DIAMETER “V” DEPTH UNLESS OTHERWISE NOTED, SEE NOTE /15/. AA TO BE FREE OF PTFE COATING.c. MATERIAL CODE “D”: CHEMICAL FILM FINISH ENTIRE PART (INCLUDING INTERNAL DIAS) P

10、ER MIL-C-5541, CLASS 1A, PTFE COAT (GREEN) EXTERNAL SURFACE AND BORE DIAMETER TO “V” DEPTH.3. LIQUID PENETRANT INSPECT PER ASTM E 1417 TYPE 1 SENSITIVITY 2LINEAR INDICATIONS PROHIBITED, ROUNDED INDICATIONS ACCEPTABLE./4/ FILL OUTER GROOVE FOR CRES AND TITANIUM WITH SILICONE. FILL ALL GROOVES FOR ALU

11、MINUM WITH SILICONE ELASTOMER.TABLE 1B - DIMENSIONS H-AABASIC NO.AS5013/15/SIZE CODE H K LN+.000.003TTHREADCLASS 3A(MIL-S-8879)V/2/ AA03 .375 .361 .155 .275 .3750-24 UNJF .170/.220 .1304 .437 .420 .163 .338 .4375-20 UNJF .190/.240 .2205 .500 .490 .178 .413 .5000-20 UNJF .200/.250 .2206 .562 .549 .13

12、4 .480 .5625-18 UNJF .220/.270 .2208 .750 .736 .225 .655 .7500-16 UNJF .410/.435 .5010 .875 .860 .174 .787 .8750-14 UNJF .410/.435 .5012 1.062 1.048 .193 .929 1.0625-12 UNJ .365/.390 .5016 1.375 1.343 .237 1.257 1.3125-12 UNJ .325/.350 .5020 1.750 1.724 .272 1.489 1.6250-12 UNJ .325/.350 .5024 2.000

13、 1.970 .283 1.786 1.8750-12 UNJ .325/.350 .50TABLE 2- WEIGHTSSIZE CODENOMINAL TUBE SIZE03.18804.25005.31206.37508.50010.62512.750161.00201.25241.50LB/EA MAX CRES .0160 .0250 .0340 .0370 .102 .132 .187 .386 .772 .818LB/EA MAX TITANIUM .00900 .0140 .0190 .0210 .0580 .0750 .106 .219 .439 .465LB/EA MAX

14、ALUMINUM .00500 .00900 .0120 .0130 .0350 .0450 .0640 .132 .264 .279AEROSPACE STANDARD AS5013 SHEET 3 OF 3 FITTING, ADAPTER, STRAIGHT FLARELESS, EXTERNAL SWAGE, HYDRAULIC NOTES (CONTINUED):/5/ THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD

15、 ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS.6. SPECIFIC DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLI

16、ANCE WITH THE PROCUREMENT SPECIFICATIONS./7/ IDENTIFICATION: PARTS SHALL BE IDENTIFIED IN THE AREA SHOWN PER AS4459.8. INTENDED USE: PER AS4459./9/ THIS EXTERNAL AREA SHALL BE FREE OF PTFE COATING.10. INTERPRETATION OF DRAWING PER ARP4296.11. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra.12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.14. DIMENSIONS IN INCHES; UNLESS OTHERWISE SPECIFIED, TOLERANCES: DIMENSIONS LINEAR .010,ANGULAR 2./15/