EN 15694-2009 en Agricultural and forestry tractors - Passenger seat - Requirements and test procedures (Incorporates Amendment A1 2015)《农业和林业拖拉机 客椅的要求和测试程序》.pdf

《EN 15694-2009 en Agricultural and forestry tractors - Passenger seat - Requirements and test procedures (Incorporates Amendment A1 2015)《农业和林业拖拉机 客椅的要求和测试程序》.pdf》由会员分享，可在线阅读，更多相关《EN 15694-2009 en Agricultural and forestry tractors - Passenger seat - Requirements and test procedures (Incorporates Amendment A1 2015)《农业和林业拖拉机 客椅的要求和测试程序》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BSEN15694:2009ICS65.060.10NOCOPYINGWITHOUTBSIPERMISSIONEXCEPTASPERMITTEDBY COPYRIGHTLAWBRITISHSTANDARDAgriculturalandforestrytractorsPassengerseatRequirementsandtestprocedures+A1:2015This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 28 February2010

2、BS EN 15694:2009+A1:2015National forewordThe UK participation in its preparation was entrusted to TechnicalCommittee AGE/6, Agricultural tractors and forestry machinery.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport

3、to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations. The British StandardsInstitution 2015. Published byBSI Standards Limited 2015ISBN 978 0 580 84330 3This British Sta

4、ndard is the UK implementation of EN 15694:2009+A1:2015. It supersedes BS EN 15694:2009 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text al

5、tered by CEN amendment A1 is indicated by !“.Amendments/corrigenda issued since publicationDate Comments 31 October 2015 Implementation of CEN amendment A1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15694:2015+A1 November 2015 ICS 65.060.10 Supersedes EN 15694:2009English Version Agric

6、ultural and forestry tractors - Passenger seat - Requirements and test procedures Tracteurs agricoles et forestiers - Sige du passager - Prescriptions et modes opratoires dessai Land- und forstwirtschaftliche Traktoren - Beifahrersitz - Anforderungen und Prfverfahren This European Standard was appro

7、ved by CEN on 20 May 2009 and includes Amendment 1 approved by CEN on 12 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lis

8、ts and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

9、 the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

10、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPE

11、N DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15694:2015+A1:2015 EEN 15694:2009+A1:2015 (E) 2 Contents Page E

12、uropean foreword . 4 Introduction 5 1 Scope 6 2 Normative references 6 3 Terms and definitions . 6 4 Requirements . 7 4.1 Location and mounting . 7 4.2 Seat dimensions . 7 4.3 Seat cushion 7 4.4 Seat belt 8 4.5 Foot rest and handles 8 4.6 Roll-over protection . 8 5 Test procedures . 8 6 Operators ma

13、nual 8 Annex A (normative) Standards to be used for testing the roll-over protective structure (see 4.6.1 and 5.1) 9 Annex B (normative) Deflection limiting volume, sequence of tests and acceptance criteria for the passenger seat (see 5.2) 10 B.1 Passenger Deflection Limiting Volume (PDLV) . 10 B.2

14、Passenger seat index point (SIPp) . 12 B.3 Allowable interference . 12 B.3.1 General . 12 B.3.2 Interference evaluation procedure . 14 B.3.3 Reversible drivers position . 15 B.4 ROPS test . 17 B.4.1 General . 17 B.4.2 Sequence of tests 17 B.4.2.1 Longitudinal loading . 17 B.4.2.2 First crushing test

15、 17 B.4.2.3 Loading from the side . 17 B.4.2.4 Second crushing test . 17 B.4.2.5 Second longitudinal loading . 17 B.4.3 Horizontal loading tests from the rear, front and side . 18 B.4.3.1 General provisions . 18 BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 3 B.4.3.2 Longitudinal loading . 18 B.

16、4.3.3 Side loading . 18 B.4.4 Crushing tests . 19 B.4.4.1 Crushing at the rear . 19 B.4.4.2 Crushing at the front 19 B.4.5 Second longitudinal loading test . 19 B.4.6 Interference measuring apparatus 20 B.4.7 Conditions for acceptance . 21 B.4.7.1 General . 21 B.4.7.2 Description of the overload tes

17、t 22 Annex C (normative) Rules and directions . 23 C.1 General . 23 C.2 Apparatus 24 C.3 Test conditions 24 C.4 Extension to other tractor models 25 C.4.1 General . 25 C.4.2 Extension of the structural test results to other models of tractors 25 C.4.3 Extension of the structural test results to modi

18、fied models of the protective structure 25 Bibliography . 27 BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 4 European foreword This document (EN 15694:2009+A1:2015) has been prepared by Technical Committee CEN/TC 144 “Tractors and machinery for agriculture and forestry”, the secretariat of which

19、 is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be withdrawn at the latest by May 2016. Attention is drawn to the possibility

20、that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1 approved by CEN on 2015-09-12. This document supersedes EN 15694:2009. The start and fini

21、sh of text introduced or altered by amendment is indicated in the text by tags !“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN/CENELEC Internal Regulations, the national standards organizations

22、of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne

23、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 5 Introduction Agricultural and forestry tractors are often equipped with a passenger seat to allow the safe, short-term and

24、occasional transport of a person from the farm to the field. The tractor and cab design is defined by and optimized for various functions and operating conditions. The passenger transport is not a main request and less comfortable conditions are accepted by the market for the benefit of the main pur

25、poses. Roll-over protective structures (ROPS) were introduced to improve the safety of the tractor driver during field operations. To allow the protection of the passenger, to consider the specific conditions of tractor design, its intended use and all risks including the risk of roll-over, the stan

26、dard should satisfy especially the following conditions: to specify requirements to be applied to all tractors respectively all operations and requirements depending on the intended use respectively operations taking into account the normal use; to specify performance based requirements correspondin

27、g to the state of art and minimizing the necessary changes in tractor design; to ensure a high level of occupational safety for both the driver and passenger during the individual operations; not to reduce the protection of the driver or passenger against other risks; to refer to available specifica

28、tions or standards; to provide repeatable and reproducible test procedures. BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 6 1 Scope This standard is applicable to agricultural and forestry tractors on which provision is made for carrying one person in addition to the driver. It specifies minimum

29、 requirements for space and support, specifies roll-over protective structures (ROPS) test procedures and seat belt requirements, by reference to other standards. It also specifies the information to be provided by the tractor manufacturer. 2 Normative references The following referenced documents a

30、re indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3463, Tractors for agriculture and forestry Roll-over protective structures (ROPS

31、) Dynamic test method and acceptance conditions ISO 3776-1, Tractors and machinery for agriculture Seat belts Part 1: Anchorage location requirements ISO 3776-2, Tractors and machinery for agriculture Seat belts Part 2: Anchorage strength requirements !ISO 5353:1995, Earth-moving machinery, and trac

32、tors and machinery for agriculture and forestry Seat index point“ ISO 5700, !Tractors for agriculture and forestry Roll-over protective structures Static test method and acceptance conditions“ ISO 12003-1, Agricultural and forestry tractors Roll-over protective structures on narrow-track wheeled tra

33、ctors Part 1: Front-mounted ROPS ISO 12003-2, Agricultural and forestry tractors Roll-over protective structures on narrow-track wheeled tractors Part 2: Rear-mounted ROPS 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 passenger seat structu

34、re which may or may not be integral with the tractor structure, complete with cushion, intended to seat and transport one adult person ! 3.2 passenger seat index point (SIPp) point located in the central longitudinal plane of the apparatus for determination when installed in the passenger seat BS EN

35、 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 7 3.3 passenger deflection-limiting volume (PDLV) volume which is defined in relation to the reference planes and the passenger seat index point (SIPp) and serving to set limits and deflections permissible when performing laboratory evaluations of the pro

36、tective structure 3.4 reference planes vertical planes being longitudinal and transversal to the tractor and passing through the passenger seat index point; these reference planes are assumed to move horizontally with the seat during loading but to remain perpendicular to the tractor or the floor of

37、 the roll-over protective structure 3.5 interference zone portion of the operator clearance zone (OCZ) where a defined maximum interference with PDLV is allowed“ 4 Requirements 4.1 Location and mounting 4.1.1 Each seat shall be so placed that the passenger is in no danger and creates no impediment t

38、o driving the tractor. 4.1.2 There shall be a vertical clearance of at least 920 mm above the surface of the passenger seat. However, where a tractor satisfies the requirements relating to the drivers protection and seating, but its construction does not allow for such a vertical clearance for the p

39、assenger, the clearance may be reduced to 800 mm, provided that adequate padding is provided immediately above the passenger seat at the level of the roof. The upper part of the vertical clearance allowed for the passenger may be limited at the rear and sides, only by a radius not exceeding 300 mm.

40、The vertical clearance is the vertical open space between the front edge of the seat and the roof of the tractor. 4.1.3 The passenger seat shall not add to the overall width of the tractor. 4.1.4 Each seat shall be firmly fixed and properly attached according to the type of tractor, to a structural

41、member of the tractor chassis, roll-over protective structure, platform, etc. The structural member concerned shall be sufficiently strong to support a laden passenger seat. 4.2 Seat dimensions 4.2.1 Each seat shall be at least 400 mm wide and at least 300 mm deep. 4.2.2 Each seat shall incorporate

42、a lateral support for position-maintenance purposes and be fitted with a back rest that is at least 200 mm high. NOTE The lateral support and/or the backrest may also be provided by parts of the cab and/or the roll-over protective structure. 4.3 Seat cushion The seat cushion shall be either padded o

43、r made from elastic materials (e.g. plastics). BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 8 4.4 Seat belt A restraint system shall be provided. The restraint system shall be in accordance with the ISO 3776- series or other applicable standards. 4.5 Foot rest and handles 4.5.1 A suitable foot

44、rest for the passengers feet shall be provided. 4.5.2 Suitable grab handles shall be provided in order to facilitate the access to the passenger seat and to help him to remain in position on it. 4.6 Roll-over protection 4.6.1 If the intended use of the passenger seat allows the transport of passenge

45、rs during field operations, the passenger shall be protected by the roll-over protective structure provided for the drivers protection or by an additional structure. 4.6.2 If the intended use of the passenger seat only allows the transport of passengers on public roads and not during field operation

46、s, a safety sign with the information that the passenger seat shall not be used during field operations shall be provided on or near to the passenger seat. In addition, this information shall be provided in the operators manual. 4.6.3 To allow the same specifications for road and field operations in

47、 the future, specific test procedure(s) and acceptance criteria are needed (see 5.2) 5 Test procedures 5.1 The roll-over protective structure provided for the protection of the driver and/or the additional structure, if provided (see 4.6.1), shall be tested in accordance with Annex A. 5.2 Annex B in

48、cludes the outline for a specific provisional test procedure and acceptance criteria (see 4.6.3). !deleted text“ 5.3 The requirements and dimensions specified in 4.1 to 4.5 shall be verified by inspection and/or measurement. 6 Operators manual The operators manual shall provide the following informa

49、tion: a) the intended use of the passenger seat; b) the obligation for the passenger to use the seat belt; c) that it is forbidden to use the passenger seat during field operations, if this use is excluded from the intended use. BS EN 15694:2009+A1:2015EN 15694:2009+A1:2015 (E) 9 Annex A (normative) Standards to be used for testing the roll-over protective structure (see 4.6.1 and 5.1) Table A.1 specifies the relevant ISO standards and shows equivalent other documents. Table A.1 ISO standards and equivalent documents ISO stan