SAE AS 4317C-2015 FITTING REDUCER ADAPTER FLARED TUBE TO BOSS FOR SEAL RING.pdf

《SAE AS 4317C-2015 FITTING REDUCER ADAPTER FLARED TUBE TO BOSS FOR SEAL RING.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4317C-2015 FITTING REDUCER ADAPTER FLARED TUBE TO BOSS FOR SEAL RING.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, REDUCER, ADAPTER, FLARED TUBE TO BOSS FOR SEAL RING AS4317Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

2、recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1993-08REAFFIRMED 2001-12REVISED 201

3、5-02THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4317 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /4/ KSC-F-124SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisrep

4、ort is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SA

5、E invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4317C RATIONALE CORRECTED END 1 TO STYLE “E” IN FIGURE 1, UPDATED NOTE /4/ TO DELETE “PRI” STATEMENT AND CORRECT THE NADCAP SCOPE TO

6、AC7112, AC7112/2. FIGURE 1 - FITTING, REDUCER, ADAPTER, FLARED TUBE TO BOSS AEROSPACE STANDARD AS4317 SHEET 2 OF 3 REV. C FITTING, REDUCER, ADAPTER, FLARED TUBE TO BOSS FOR SEAL RING TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NUMBER AS4317 /15/ SIZE CODE (NOMINAL TUBE SIZE) END 1 T1 THREAD PER AS8879 CL

7、ASS 3A END 1 (NOMINALTUBE SIZE) END 2 T2 THREAD PER AS8879 CLASS 3A END 2 A +.000.063B .030C D .010E LB/EA APPROXREF ALUM LB/EAAPPROXREF CRES 0402 .250 .4375-20UNJF .125 .3125-24UNJF 1.100 .092 .452 .668 .678- .691 .0170 .0471 0403 .250 .4375-20UNJF .188 .3750-24UNJF 1.066 .073 .452 .668 .678- .691

8、.0160 .0442 0602 .375 .5625-18UNJF .125 .3125-24UNJF 1.242 .160 .457 .792 .802- .815 .0317 .0877 0603 .375 .5625-18UNJF .188 .3750-24UNJF 1.208 .141 .457 .792 .802- .815 .0298 .0826 0604 .375 .5625-18UNJF .250 .4375-20UNJF 1.335 .187 .457 .792 .802- .815 .0364 .1010 0605 .375 .5625-18UNJF .313 .5000

9、-20UNJF 1.335 .176 .457 .792 .802- .815 .0354 .0979 0802 .500 .7500-16UNJF .125 .3125-24UNJF 1.357 .167 .538 .980 .990-1.003 .0534 .148 0803 .500 .7500-16UNJF .188 .3750-24UNJF 1.323 .148 .538 .980 .990-1.003 .0503 .139 0804 .500 .7500-16UNJF .250 .4375-20UNJF 1.450 .194 .538 .980 .990-1.003 .0599 .

10、166 0805 .500 .7500-16UNJF .313 .5000-20UNJF 1.450 .183 .538 .980 .990-1.003 .0582 .161 0806 .500 .7500-16UNJF .375 .5625-18UNJF 1.445 .176 .538 .980 .990-1.003 .0568 .158 1004 .625 .8750-14UNJF .250 .4375-20UNJF 1.533 .185 .618 1.103 1.113-1.128 .0769 .213 1006 .625 .8750-14UNJF .375 .5625-18UNJF 1

11、.528 .167 .618 1.103 1.113-1.128 .0730 .202 1008 .625 .8750-14UNJF .500 .7500-16UNJF 1.567 .136 .618 1.103 1.113-1.128 .0731 .203 1204 .750 1.0625-12UNJ .250 .4375-20UNJF 1.686 .209 .703 1.353 1.363-1.380 .125 .347 1205 .750 1.0625-12UNJ .313 .5000-20UNJF 1.686 .198 .703 1.353 1.363-1.380 .121 .336

12、1206 .750 1.0625-12UNJ .375 .5625-18UNJF 1.681 .191 .703 1.353 1.363-1.380 .119 .329 1208 .750 1.0625-12UNJ .500 .7500-16UNJF 1.719 .159 .703 1.353 1.363-1.380 .115 .319 1210 .750 1.0625-12UNJ .625 .8750-14UNJF 1.816 .185 .703 1.353 1.363-1.380 .127 .351 1604 1.000 1.3125-12UNJ .250 .4375-20UNJF 1.7

13、22 .203 .741 1.603 1.613-1.630 .172 .476 1608 1.000 1.3125-12UNJ .500 .7500-16UNJF 1.809 .181 .741 1.603 1.613-1.630 .167 .464 1610 1.000 1.3125-12UNJ .625 .8750-14UNJF 1.852 .179 .741 1.603 1.613-1.630 .170 .472 1612 1.000 1.3125-12UNJ .750 1.0625-12UNJ 1.912 .175 .741 1.603 1.613-1.630 .177 .490 2

14、004 1.250 1.6250-12UNJ .250 .4375-20UNJF 1.965 .301 .778 1.853 1.863-1.880 .307 .852 2012 1.250 1.6250-12UNJ .750 1.0625-12UNJ 2.202 .296 .778 1.853 1.863-1.880 .316 .875 2016 1.250 1.6250-12UNJ 1.000 1.3125-12UNJ 2.202 .278 .778 1.853 1.863-1.880 .302 .839 2416 1.500 1.8750-12UNJ 1.000 1.3125-12UNJ

15、 2.159 .194 .878 2.099 2.109-2.135 .333 .923 2420 1.500 1.8750-12UNJ 1.250 1.6250-12UNJ 2.154 .192 .878 2.099 2.109-2.135 .340 .943 2820 1.750 2.2500-12UNJ 1.250 1.6250-12UNJ 2.373 .239 .978 2.474 2.484-2.510 .410 1.150 2824 1.750 2.2500-12UNJ 1.500 1.8750-12UNJ 2.404 .230 .978 2.474 2.484-2.510 .43

16、1 1.210 3224 2.000 2.5000-12UNJ 1.500 1.8750-12UNJ 2.529 .230 1.078 2.724 2.734-2.760 .502 1.410 3228 2.000 2.5000-12UNJ 1.750 2.2500-12UNJ 2.684 .282 1.08 2.724 2.734-2.760 .600 1.680 NOTES: /1/ MATERIAL: a. CODE LETTER D: TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS4112; OR TYPE 2024-

17、T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. b. CODE LETTER J: 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639. c. CODE LETTER K: 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648. d. CODE LETTER R: 321 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645. e. CODE LETTE

18、R S: 347 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5646. f. CODE LETTER W: TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. AEROSPACE STANDARD AS4317 SHEET 3 OF 3 REV. C FITTING, REDUCER, ADAPTER, FLARED TUBE TO BOSS FOR SEAL RING 2. H

19、EAT TREAT: a. ALL CODE LETTERS: NONE 3. FINISH: a. MATERIAL CODE LETTER D: ANODIZE PER AMS2472 OR MIL-A-8625 TYPE II, CLASS 2, DYE BLUE AND DUPLEX SEAL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS J, K, R, AND S; PASSIVATE PER AMS2700, TYPE 6 OR TYPE 7. c. MATERIAL CODE LETTER W: ANODIZE

20、PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: KSC-F-124 JOHN F KENNEDY SPACE CENTER, NASA, SPECIFICATION FOR FITTINGS (PRESSURE CONNECTIONS), FLARED TUBE. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED

21、BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURERS LIST (QML) AC7112, AC7112/2 FOR SIMILAR FLARED FITTINGS. THE QML IS AVAILABLE AT www.eAuditN. /5/ IDENTIFICATION: MARK PER AS478 CLASS C OR CLASS D; METHOD 7A

22、3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. /6/ AT THE OPTI

23、ON OF THE MANUFACTURER, THE SMALLER DIAMETER MAY BE DRILLED THRU. /7/ THE SEAL RING IS ORDERED SEPARATELY AS AN AS1097. 8. INTERPRETATION OF DRAWING PER AS4296. 9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES ARE TO BE 125 MICR

24、OINCHES Ra. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 12. DIMENSIONS IN INCHES UNLESS OTHERWISE SPECIFIED; TOLERANCES: LINEAR DIMENSIONS .016; ANGULAR DIMENSIONS 030. 13. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENI

25、ENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED I

26、N ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 14. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. 15. EXAMPLE OF PART NUMBER: AS4317 K 08 06 BASIC PART NUMBER SIZE CODE: TUBE SIZE OF END 2 IN .062 INCREMENTS MATERIAL CODE LETTER /1/ SIZE CODE: TUBE SIZE OF END 1 IN .062 INCREMENTS