SAE AS 1718E-2016 COUPLING BODY FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS.pdf

《SAE AS 1718E-2016 COUPLING BODY FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1718E-2016 COUPLING BODY FLEXIBLE VARIABLE CAVITY THREADED FERRULE TYPE TUBE ENDS.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD COUPLING BODY, FLEXIBLE, VARIABLE CAVITY, THREADED FERRULE TYPE TUBE ENDS AS1718Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

2、hotocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1982-05 REAFFIRMED2013-0

3、1 REVISED2016-04 THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A REV.E FEDERAL SUPPLY CLASS 4730 AS1718 SHEET 1 OF 3 REV. E PROCUREMENT SPECIFICATION: AS1710, SEE NOTE 3 SAE Technical Standards Board Rules providethat: “This reportis published bySAEto advance the state oftechnicaland engineering sciences

4、. The use of this report isentirely voluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,isthe soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,

5、orcancelled. SAE invites yourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS1718E RATIONALE CORRECT THE DRAFTING ERROR OF .500 .015 DIMENSION IN SECTION A-A. ADD GENERAL NOTE 14. CORRECT ANGULAR

6、 TOLERANCE ERROR IN NOTE 8. FIGURE 1 - BODY .500 .015 AEROSPACE STANDARD AS1718 SHEET 2 OF 3 REV. E COUPLING BODY, FLEXIBLE, VARIABLE CAVITY, THREADED FERRULE TYPE TUBE ENDS TABLE 1 - COUPLING BODY DIMENSIONS AND WEIGHTS AEROSPACE STANDARD AS1718 SHEET 3 OF 3 REV. E COUPLING BODY, FLEXIBLE, VARIABLE

7、 CAVITY, THREADED FERRULE TYPE TUBE ENDS NOTES: 1. MATERIAL: ALUMINUM ALLOY 2024-T6, 2024-T851, 2024-T8510, OR T2024-T8511 PER AMS-QQ-A-225/6 OR AMS-QQ-A-200/3. 2. FINISH: ANODIZE PER MIL-A-8625, TYPE II, CLASS 1 OR CLASS 2, COLOR OPTIONAL. /3/ COUPLING BODIES SUPPLIED TO THIS SPECIFICATION SHALL BE

8、 MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER OR SUPPLIED BY AN ACCREDITED DISTRIBUTOR LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS1710 FOR THIS STANDARD. THE QPL IS AVAILABLE AT www.eAuditN. /4/ IDENTIFICATION PER AS478 METHOD 30 INCLUDING THE

9、MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE, COMPLETE “AS” PART NUMBER, AND DATE OF MANUFACTURE IN QUARTERS (3Q95 = THIRD QUARTER 1995). SIZES 12 AND SMALLER MAY BE INDIVIDUALLY PLACED IN A PLASTIC BAG WITH A TAG CONTAINING THIS INFORMATION. /5/ THE MANUFACTURER WILL SPECIFY AND CONTROL CERTAIN SPEC

10、IFIC DIMENSIONS AND TOLERANCES AND WILL BE RESPONSIBLE TO ASSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLIANCE WITH THE PERFORMANCE REQUIREMENTS OF AS1710. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES

11、Ra MAX. 7. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 8. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2. /9/ TOLERANCE IS .005 FOR SIZES 08 THROUGH 28 AND .010 FOR SIZES 32 THROUGH 88. /10/ TOLERANCE IS +.004/-.000 FOR SIZES 08 THR

12、OUGH 36 AND +.006/-.000 FOR SIZES 40 THROUGH 88. /11/ TOLERANCE IS +.010/-.000 FOR SIZES 08 THROUGH 28 AND .010 FOR SIZES 32 THROUGH 88. 12. EXAMPLE OF PART NUMBER: 13. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICA

13、L REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 14. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION.