SAE AMS 2814G-2011 Packaging and Marking of Packages of Welding Wire Premium Quality《优质焊条的封装的包装和标记》.pdf

《SAE AMS 2814G-2011 Packaging and Marking of Packages of Welding Wire Premium Quality《优质焊条的封装的包装和标记》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 2814G-2011 Packaging and Marking of Packages of Welding Wire Premium Quality《优质焊条的封装的包装和标记》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS2814G AEROSPACE MATERIAL SPECIFICATION AMS2814 REV. G Issued 1963-01 Revised 2011-03 Reaffir

5、med 2017-08 Superseding AMS2814F Packaging and Marking of Packages of Welding Wire Premium Quality RATIONALE AMS2814G has been reaffirmed to comply with the SAE Five-Year Review policy. 1. SCOPE This specification covers spooling and packaging of bare welding wire to ensure cleanliness and freedom f

6、rom corrosion, spool sizes and weights of spooled wire, and package weights of cut lengths. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequen

7、t revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive

8、, Warrendale PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2816 Identification, Welding Wire, Tab Marking System AMS2819 Identification, Welding Wire, Direct Color Code System 2.2 American Welding Society Publication Available from American W

9、elding Society, 550 N.W. LeJeune Road, Miami, FL 33126, . AWS A5.02/A5.02M Specification for Filler Metal Standard Sizes, Packaging, and Physical Attributes 3. TECHNICAL REQUIREMENTS 3.1 Preparation Prior to winding on spools or cutting to length, wire shall be uncoiled for cleaning and shall be ren

10、dered free of dirt, grease, oil, corrosion, and other surface contamination which would interfere with welding. The cleaning method shall not introduce hydrogen to the wire. Chlorinated solvents shall not be used on titianium alloys. 3.2 Packaging shall be in accordance with AWS A5.02/A5.02M and the

11、 following: Packaging shall be performed in an atmosphere of sufficiently low humidity, depending upon the corrosion rate of the alloy, to ensure that wire will not corrode during the packaging operation. Wire, after cleaning preparatory to packaging, shall not be handled with bare hands or unclean

12、gloves. 3.2.1 Spooled Wire 3.2.1.1 Both ends of the spooled wire shall be so treated that it may be readily located for verification purposes. 3.2.1.2 Net weight of wire on spools shall be specified in Table 1 for the alloy type ordered. TABLE 1A - SPOOL WIRE WEIGHT, INCH/POUND UNITS Alloy Base Net

13、Weight Pounds Aluminum 1, 5, 10, 12-1/2, 15 Magnesium 3/4, 1, 3, 10 Titanium 1, 5, 10, 15, 20 Copper 1, 10, 25, 50 Steel, Corrosion and Heat Resistant Alloys and Refractory Alloys 1-1/2, 2-1/2, 10, 12, 15, 25, 30, 35, 44, 50, 60 TABLE 1B - SPOOL WIRE WEIGHT, SI UNITS Alloy Base Net Weight Kilograms

14、Aluminum 0.45, 2.3, 4.5, 5.7, 6.8 Magnesium 0.3, 0.5, 4.5 Titanium 0.5, 2.2, 4.5, 6.8, 9.1 Copper 0.45, 4.5, 11.3, 22.7 Steel, Corrosion and Heat Resistant Alloys and Refractory Alloys 0.7, 1.1, 4.5, 5.5, 6.8, 11.3, 13.6, 15.9, 20, 22.7, 27.2 3.2.1.3 Spooled wire shall be packaged in hermetically se

15、aled containers with a desiccant and/or a dry, inert atmosphere. When specified, the hermetically sealed containers shall be so designed that they can be used for storage after opening. 3.2.2 Cut Lengths 3.2.2.1 Envelopes shall be made of a material free from oil and other substances detrimental to

16、welding operations. Envelope material used in packaging wire which is susceptible to corrosion shall have a water vapor transmission rate lower than 0.05 grams per 100 square inches (0.775 g/m2) per 24 hours at 100 F (38 C) and 90% relative humidity. Envelopes shall be of sufficient strength to with

17、stand normal handling; ends of wires may be capped to prevent puncturing the envelope. Envelopes may be purged with inert gas and this gas maintained as the atmosphere in the envelope; desiccants may also be added for further protection against oxidation and corrosion of the wire. Envelopes in which

18、 an inert gas atmosphere is used shall be heat sealed. SAE INTERNATIONAL AMS2814G Page 2 of 5_ 3.2.2.2 Unless otherwise specified in the material specification, no package shall contain wire from more than one heat of alloy, except in the case of aluminum and magnesium alloys which are not restricte

19、d. 3.2.2.3 Not more than 40 lengths of wire shall be packaged in an envelope or in each compartment of a multiple-compartment envelope, unless otherwise specified. The weight of wire in each envelope or each compartment shall be not greater than shown in Table 2. TABLE 2A - WEIGHT OF WIRE, POUNDS PE

20、R ENVELOPE OR COMPARTMENT, INCH/POUND UNITS Alloy Type For Wire Diameters Inch Up to 0.035, incl For Wire Diameters Inch Over 0.035to 0.050, incl For Wire Diameters Inch Over 0.050to 0.080, incl For Wire Diameters Inch Over 0.080 to 0.100, incl For Wire DiametersInch Over 0.100 Aluminum, Magnesium,

21、and Titanium 1.0 1.0 2.0 2.0 5.0 All Others 1.0 2.0 5.0 10.0 10.0 TABLE 2B - WEIGHT OF WIRE, KILOGRAMS PER ENVELOPE OR COMPARTMENT, SI UNITS Alloy Type For Wire Diameter Millimeter Up to 0.89, incl For Wire Diameter Millimeter Over 0.89 to 1.27, incl For Wire Diameter Millimeter Over 1.27 to 2.03, i

22、ncl For Wire Diameter Millimeter Over 2.03 to 2.54, incl For Wire Diameter Millimeter Over 2.54 Aluminum, Magnesium, And Titanium 0.45 0.45 0.91 0.91 2.3 All Others 0.45 0.91 2.3 4.5 4.5 3.3 Packaging 3.3.1 Containers of wire shall be packaged to ensure that the wire, during shipment and storage, wi

23、ll be protected against mechanical injury, corrosion, dirt, grease, oil, and other contamination detrimental to welding. 3.3.2 Exterior containers of spooled wire shall contain the ordered multiple of standard spool net weights up to a maximum net weight of 120 pounds (54.4 kg). 3.3.3 Exterior shipp

24、ing containers of cut lengths shall contain approximately 5, 10, 25, 50, or 100 pounds (2.3, 4.5, 11.3, 22.7, or 45.3 kg), as ordered. 3.3.4 Containers shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the hand

25、ling, packaging, and transportation of the wire to ensure carrier acceptance and safe delivery. SAE INTERNATIONAL AMS2814G Page 3 of 5_ 3.4 Marking Each length of wire shall be marked in accordance with AMS2816, AMS2819 or other method acceptable to the purchaser. Interior containers of spools and c

26、ut lengths and all exterior shipping containers shall be marked as follows: 3.4.1 Interior containers shall be permanently and legibly marked with not less than the following information; for envelopes of cut lengths, the information may appear on an attached label or the label may be inserted in th

27、e envelope if the envelope is made of transparent material: WIRE, WELDING WIRE SPECIFICATION NUMBER (and revision letter if any) SIZE QUANTITY HEAT NUMBER (If applicable) MANUFACTURERS IDENTIFICATION WIRE IDENTIFICATION SPECIFICATION CODE NUMBER DO NOT HANDLE WIRE WITH BARE HANDS OR UNCLEAN GLOVES.

28、OPEN CONTAINERS (ENVELOPES) SHALL NOT BE RETURNED TO STOCKROOM. 3.4.2 Exterior Shipping Containers Shall be permanently and legibly marked with not less than the following information: WIRE, WELDING WIRE SPECIFICATION NUMBER (and revision letter if any) SIZE QUANTITY HEAT NUMBER (If applicable) PURC

29、HASE ORDER NUMBER MANUFACTURERS IDENTIFICATION PACKAGED PER AMS2814 WIRE IDENTIFICATION SPECIFICATION 4. QUALITY ASSURANCE PROVISIONS Not applicable. 5. PREPARATION FOR DELIVERY See Section 3. 6. ACKNOWLEDGMENT Not applicable. 7. REJECTIONS Wire not packaged in accordance with this specification, or

30、 with modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS2814G Page 4 of 5_ 8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the pre

31、vious issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clari

32、fied in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. PREPARED BY AMS COMMITTEE “B“ SAE INTERNATIONAL AMS2814G Page 5 of 5_