SAE AMS 2810H-2018 Identification and Packaging Elastomeric Products.pdf

《SAE AMS 2810H-2018 Identification and Packaging Elastomeric Products.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 2810H-2018 Identification and Packaging Elastomeric Products.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2018 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS2810H AEROSPACE MATERIAL SPECIFICATION AMS2810 REV. H Issued 1944-11 Revised 2018-01 Superse

5、ding AMS2810G Identification and Packaging Elastomeric Products RATIONALE This specification is being revised to add the material specification number to the packaging in order to be consistent with AMS2817 Section 5. 1. SCOPE This specification provides requirements for the identification and packa

6、ging of sheet, strip, extrusions, and molded parts made of natural rubber, synthetic rubber, reclaimed rubber, and combinations of the above with other materials such as asbestos, cork, and fabrics. AMS2817 covers preferred requirements for identification and packaging of preformed packings. 2. APPL

7、ICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced documen

8、t has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside

9、USA), www.sae.org. AS478 Identification Marking Methods ARP5316 Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959

10、, Tel: 610-832-9585, www.astm.org. ASTM D1418 Standard Practice for Rubber and Rubber Lattices Nomenclature SAE INTERNATIONAL AMS2810H Page 2 of 4 3. TECHNICAL REQUIREMENTS 3.1 Production Identification Shall be as follows: 3.1.1 Sheet 8 Inches (203 mm) and Over in Width 3.1.1.1 Sheet Ordered to Spe

11、cification Shall be marked with the specification number and its revision letter if any, manufacturers name or identification mark, compound or style number, date of cure, color if different from that required by the material specification, and nominal thickness. 3.1.1.2 Sheet Not Ordered to Specifi

12、cation Shall be marked with the manufacturers name or identification mark, compound or style number, date of cure, and nominal thickness. 3.1.2 Sheet Under 8 Inches (203 mm) in Width, Strip, Extrusions, and Molded Tubes Shall be marked with the information of 3.1.1 and the part or die number when ap

13、plicable. Tubing shall also be marked with the nominal OD or ID, as ordered, and wall thickness. 3.1.3 Molded and Fabricated Parts Shall be marked with the part number and change designation, date of cure, and the manufacturers designation. 3.2 Marking Methods and Location 3.2.1 Sheet 8 Inches (203

14、mm) and Over in Width Shall be marked in accordance with AS478, Method 30. The markings shall be applied in rows of recurring characters spaced not more than 5 inches (127 mm) apart, running either lengthwise or crosswise of the sheet, and on one face only. The characters shall be of such size as to

15、 be legible and shall not be obliterated by normal handling. 3.2.2 Sheet Under 8 Inches (203 mm) in Width, Strip, Extrusions, and Molded Tubes Shall be marked in accordance with AS478, Method 30. The markings shall appear in a row of characters recurring at intervals not greater than 3 feet (914 mm)

16、 or at each end of lengths shorter than 3 feet (914 mm). The characters shall be of such size as to be legible and shall not be obliterated by normal handling. 3.2.3 Molded and Fabricated Parts Shall be marked in accordance with AS478, Method 37, except as specified in 3.2.3.1, or as determined by a

17、 procedure agreed upon by purchaser and vendor. 3.2.3.1 When the integral symbol of AS478 appears on the drawing, parts shall be marked in accordance with AS478, Method 1A. 4. QUALITY ASSURANCE PROVISIONS Not applicable. SAE INTERNATIONAL AMS2810H Page 3 of 4 5. PREPARATION FOR DELIVERY 5.1 Packagin

18、g and Package Identification 5.1.1 The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. Packag

19、ing shall conform to carrier rules and regulations applicable to the mode of transportation. 5.1.1.1 Elastomeric products subject to deterioration by environmental factors, such as ozone and light, shall be packaged in materials which will not be degraded by, or permit transmission of, the environme

20、nt to the product. 5.1.2 Unless otherwise specified in the Purchase Order, each package shall be permanently and legibly marked with not less than the following information: MANUFACTURERS NAME AND/OR IDENTIFICATION (CAGE CODE) (This is the ID for the location where parts were manufactured.) PART NAM

21、E PART NUMBER OR FORM (as applicable) MATERIAL SPECIFICATION NUMBER (if ordered to a material specification) COMPOUND OR STYLE NUMBER CURE DATE (QUARTER AND YEAR) AND BATCH NUMBER QUANTITY OF PARTS OR PIECES (as applicable) CUSTOMERS PURCHASE ORDER NUMBER PACKAGER AND PACKAGE DATE (MONTH AND YEAR) (

22、if different than manufacturer) MATERIAL CODE PER ASTM D1418 SHELF LIFE PER ARP5316 (If required by Purchaser) 5.1.3 The elastomer products shall be packed in cartons in such a manner that the products, during shipment and storage, will not be permanently distorted and will be protected against dama

23、ge from exposure to weather or any other normal hazard. Unless otherwise specified in the Purchase Order, each carton shall be marked with not less than the following information: MATERIAL SPECIFICATION NUMBER (if ordered to a material specification) PART NUMBER COMPOUND NUMBER MANUFACTURERS IDENTIF

24、ICATION PURCHASE ORDER NUMBER QUANTITY DATE OF SHIPMENT 5.1.4 Cartons shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the elastomer products to ensure carrier ac

25、ceptance and safe delivery. Packaging shall conform to carrier rules and regulations applicable to the mode of transportation. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. SAE INTERNATIONAL AMS281

26、0H Page 4 of 4 7. NOTES 7.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title ind

27、icates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 7.2 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and pr

28、operties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 7.3 Procedures conforming to the requirements of this specification have been classified under Federal Supply Classification (FSC) 9320. PREPARED BY AMS COMMITTEE “CE”