SAE AMS 2810G-2008 Identification and Packaging Elastomeric Products《弹性产品的识别和包装》.pdf

《SAE AMS 2810G-2008 Identification and Packaging Elastomeric Products《弹性产品的识别和包装》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 2810G-2008 Identification and Packaging Elastomeric Products《弹性产品的识别和包装》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)

4、Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS2810GAEROSPACEMATERIALSPECIFICATIONAMS2810G Issued 1944-11 Revised 2008-12 Superseding AMS2810F

5、 (R) Identification and Packaging Elastomeric Products RATIONALEAMS2810G is a Five Year Review and update of this specification. 1. SCOPE This specification provides requirements for the identification and packaging of sheet, strip, extrusions, and molded parts made of natural rubber, synthetic rubb

6、er, reclaimed rubber, and combinations of the above with other materials such as asbestos, cork, and fabrics. AMS2817 covers preferred requirements for identification and packaging of preformed packings.2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchas

7、e order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published is

8、sue of that document shall apply. 2.1 SAE Publications International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.ARP5316 Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element, Pri

9、or to Hardware Assembly AS478 Identification Marking Methods 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D 1418 Standard Practice for Rubber and Rubber Lattices Nomenclature Copy

10、right SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS2810G Page 2 of 43. TECHNICAL REQUIREMENTS 3.1 Production Identification Shall be as follows: 3.1.1 Sheet 8 Inches (203 mm) and Over in Width 3.1.1.

11、1 Sheet Ordered to Specification Shall be marked with the specification number and its revision letter if any, manufacturers name or identification mark, compound or style number, date of cure, color if different from that required by the material specification, and nominal thickness. 3.1.1.2 Sheet

12、Not Ordered to Specification Shall be marked with the manufacturers name or identification mark, compound or style number, date of cure, and nominal thickness. 3.1.2 Sheet Under 8 Inches (203 mm) in Width, Strip, Extrusions, and Molded Tubes Shall be marked with the information of 3.1.1 and the part

13、 or die number when applicable. Tubing shall also be marked with the nominal OD or ID, as ordered, and wall thickness. 3.1.3 Molded and Fabricated Parts Shall be marked with the part number and change designation, date of cure, and the manufacturers designation. 3.2 Marking Methods and Location 3.2.

14、1 Sheet 8 Inches (203 mm) and Over in Width Shall be marked in accordance with AS478, Method 30. The markings shall be applied in rows of recurring characters spaced not more than 5 inches (127 mm) apart, running either lengthwise or crosswise of the sheet, and on one face only. The characters shall

15、 be of such size as to be legible and shall not be obliterated by normal handling. 3.2.2 Sheet Under 8 Inches (203 mm) in Width, Strip, Extrusions, and Molded Tubes Shall be marked in accordance with AS478, Method 30. The markings shall appear in a row of characters recurring at intervals not greate

16、r than 3 feet (914 mm) or at each end of lengths shorter than 3 feet (914 mm). The characters shall be of such size as to be legible and shall not be obliterated by normal handling. 3.2.3 Molded and Fabricated Parts Shall be marked in accordance with AS478, Method 30, except as specified in 3.2.3.1

17、and 3.2.3.2. 3.2.3.1 When the integral symbol of AS478 appears on the drawing, parts shall be marked in accordance with AS 478, Method 1A. 3.2.3.2 If marking by AS478, Method 30, is impracticable because of the size or shape of the part and marking by AS478, Method 1A, is not specified, parts shall

18、be identified in accordance with AS478, Method 37. 4. QUALITY ASSURANCE PROVISIONS Not applicable. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS2810G Page 3 of 45. PREPARATION FOR DELIVERY

19、5.1 Packaging and Package Identification 5.1.1 The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe deli

20、very. Packaging shall conform to carrier rules and regulations applicable to the mode of transportation. 5.1.1.1 Elastomeric products subject to deterioration by environmental factors, such as ozone and light, shall be packaged in materials which will not be degraded by, or permit transmission of, t

21、he environment to the product. 5.1.2 Unless otherwise specified in the Purchase Order, each package shall be permanently and legibly marked with not less than the following information: MANUFACTURERS NAME AND/OR IDENTIFICATION (CAGE CODE) (This is the ID for the location where parts were manufacture

22、d.)PART NAME PART NUMBER OR FORM (as applicable) AMS2810GCOMPOUND OR STYLE NUMBER CURE DATE (QUARTER AND YEAR) AND BATCH NUMBER QUANTITY OF PARTS OR PIECES (as applicable) CUSTOMERS PURCHASE ORDER NUMBERPACKAGER AND PACKAGE DATE (MONTH AND YEAR) (If different than Manufacturer.)MATERIAL CODE PER AST

23、M D 1418 SHELF LIFE PER ARP5316 (If required by Purchaser.) 5.1.3 The elastomer products shall be packed in cartons in such a manner that the products, during shipment and storage, will not be permanently distorted and will be protected against damage from exposure to weather or any other normal haz

24、ard. Unless otherwise specified in the Purchase Order, each carton shall be marked with not less than the following information: AMS2810GPART NUMBERCOMPOUND NUMBER MANUFACTURERS IDENTIFICATION PURCHASE ORDER NUMBERQUANTITYDATE OF SHIPMENTCopyright SAE International Provided by IHS under license with

25、 SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS2810G Page 4 of 45.1.4 Cartons shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transp

26、ortation of the elastomer products to ensure carrier acceptance and safe delivery. Packaging shall conform to carrier rules and regulations applicable to the mode of transportation. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when

27、acknowledging purchase orders. 7. NOTES 7.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indica

28、tes a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 7.2 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and prope

29、rties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 7.3 Procedures conforming to the requirements of this specification have been classified under Federal Supply Classification (FSC) 9320. Prepared by AMS Committee “CE” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-